1-1

The sixth lesson of the third unit in the second year would be numbered ____?

2-3-6

To look up the federal safety regulations for construction work, you would refer to ____?

29 CFR 1910

Guardrail systemsmust be constructed with a rail height of (plus or minus three inches) to meet the requirement of fall protection.

42"

........ Anchor point, when using the rescue block method, should be located on the boom ______ from the basket.

8 1/2'

How far should a climber keep his/her knees away from the pole while climbing?

8"

According to the "Code of Federal Regulations" while working on a wood structure you should wear _____?

A body belt and fall protection device

This apprenticeship program is designed to mold you into a competent, qualified craftsman with skill, knowledge, and ____?

Ability

OHSA mandates that every lineman must be trained in pole top rescue and the lineman's rescue ski must be reviewed _______?

Annually

Apprenticeship comes with responsibilities; ou acknowledged and accepted these responsibilities when you signed both the _____ and the _____.

Application / apprenticeship agreement

When working around a bucket truck, everyone on the crew should know how to operate the lower bucket/ boom controls which are normally located _____?

At the base of the lower boom on the turntable

What is the name of this tool?

Auger bit

What is the name of this tool?

Block and tackle

a(n)_____ stores electrical energy

Capacitor

The OSH Act authorizes OSHA to conduct work place inspections. Under the OSHA inspection system, which type of inspection causes the highest priority?

Catastrophes and fatal accidents

What is the name of this tool?

Chain hoist

Two early leaders in the electrical contracting industry worked diligently to bring about the industry's first "National Labor Agreement" Who were they?

Charles Ford and L.K. Comstock

A _____point on a gaff causes the gaff to keep penetrating into the wood

Chisel

Climber cutouts are listed under five general headings. Which item listed is considered a climber cutout heading?

Clothing

Apparel worn by electrical workers while working in close proximity to energized lines and equipment should be made from ____?

Cotton

How often should a student read and/or study for his or her apprenticeship?

Daily

Small tools carried in body belts should be placed so that they present the least likelihood of coming in accidental contact with _____?

Energized parts

An apprentice can be dismissed from apprenticeship for unsatisfactory performance during on-the-job training, or_____?

Failure to meet AJATC standards during related instruction

A sharpening stone should be used for ____?

Final gaff finishing or honing

Foremen shall insist that all persons under their supervision keep their belts, spurs, and straps _____?

In good condition

All tools used on energized equipment should be ______

Insulated

When performing a pole top rescue, what is the first thing you should look for when evaluating the situation from the ground?

Is the victim still in contact with the line?

Five things that should be checked when inspecting the gaffs of your climbers are: gaff tip, tip contour, width, thickness, and ____?

Length

Three factors that determine the extent of injury from an electrical shock are amount of current, path of current through the body, and ___?

Length of time current is applied

The proper procedure for descending a pole (in sequence) is _ and _ all your weight on each leg on the way down the pole.

Lock/Aim/Drop

If your safety instructions state that something SHALL be done, this means it is ____?

Mandatory

What two key elements require successful performance by the apprentice during this apprenticeship?

On-the-job training and related academic instruction

A system that utilizes a body belt or body harness rigged in a manner that permits the employee to be supported on an elevated vertical surface and work with both hands free is the ______system?

Personal fall arrest

The proper method for answering questions in your workbook is to ______?

Read and study the reference material, then attempt to answer the questions

a(n) _____ is a device that is used to raise or lower the primary voltage of a line to ensure its optimal voltage range.

Regulator

You and other apprentices were chosen by the AJATC to participate in this program because you displayed positive qualities of aptitude, _______, motivation, and personality.

Responsibility

The ever-changing electrical trade is preparing to master and profit from technological advances in work methods, equipment, and _____?

Safety

The United States is currently experiencing a ______ shortage

Skilled labor

When climbing or descending a pole, you should always support your weight by ______?

Straightening your leg and locking your knee

Who has the responsibility of observing climbing activities and bringing unsafe practes to the climber's attention?

The Foreman

When a person bridges himself of herself across an open point in a circuit, he or she is exposed to of the circuit and all the current the voltage is able to drive throu his or her body.

The full line voltage

The causes of accidents fall into three categories; acts of nature, defective equipment/ inadequate protective devices, and ______?

The human element

Who has the responsibility for inspecting, maintaining, and rejecting unsafe climbing equipment?

The person using the climbing equipment

When an injured climber is conscious and insists on climbing down the pole without assistance, what should the rescuer do?

The rescuer should insist on rigging the handline as you would for a rescue and maintain tension on the line during the descent

Leather parts of your climbing equipment should be cleaned and dressed

Three times per year

To secure a line clearance on a line means ?

To have the line de-energized

Which of the following areas is a major part of the OSHA Fall Protection Stndard? a. Fall protection system criteria and practices

Training requirements

a(n)_____ is used to step the voltage up or down in an electrical system

Transformer

For surface preservation of wooden tools, such as ladders, pike poles, switch sticks, and insulating platforms, _______ preservatives shall only be used

Transparent

Who is responsible for your apprenticeship?

You