Assessment Test

Your inside locals are not being translated to the inside global address. Which of the ff commands will show you if your inside globals are allowed to use the NAT pool? ip nat pool Corp 198.18.41.129 198.18.41.134 netmask 255.255.255.248 ip nat inside source list 100 int pool Corp overload

Show access-list

Which router command allows you to view the entire contents of all access lists?

Show access-lists

Which command allows you to view the technology options and licenses that are supported on your router along with several status variables?

Show license feature

What's the default QoS queue for a WLAN?

Silver

What are the two main types of access control lists (ACLs)?

Standard Extended

Which QoS mechanism will drop traffic if a session1 uses more than the allotted bandwidth?

Policing

Which of the ff is the valid host range for the subnet on which the IP address 192.168.168.188.255.255.255.192 resides?

192.168.168.129-190

When do two adjacent routers enter the 2WAY state?

After both routers have received the Hello information

What command do you use to lookup a module in Ansible?

Ansible-Playbook

The protocol date unit (PDU) encapsulation is completed in which order?

Data, segments, packets, frames, bits

If you wanted to delete the configuration stored in NVRA, chose the best answer for the Cisco objective

Erase startup

You have four RSTP PVST+ links between switches and want to aggregate the bandwidth. What solution will you use?

Ether Channel

IPv6 unicast routing is running on the Corp router. Which of the following addresses would show up with the show ipv6 int brief command? Corp#sh int f0/0 FastEthernet0/0 is up, line protocol is up Hardware is AmdFE, address is 000d.bd3b.0d80 (bia 000d.bd3b.0d80) [output cut]

FE80::3c3d:2d:bdff:fe3b:0d80

Which statement about GRE is not true?

GRE has security

What can the Code Preview feature be used for?

Generates a sample code snippet to call the Restful API resource in the scripting language to your choice.

You are using the code preview feature. Which of the following is this used for?

Generates a sample code snippet to call the restful

You have 2 OSPF directly configured routers that are not forming an adjacency. What should you check?

Hello and dead timers, Area and IP address/subnet mask

Which one of the ff is true regarding VLANs?

You need to have a trunk link configured between switches in order to send information about more than one VLAN down the link.

What command is used to create a backup configuration?

copy running-config startup-config

On which interface do you configure an IP address for a switch?

int vlan 1

Which of the ff commands will allow you to set your Telnet password on a Cisco router?

line vty 0 4

Which two of the ff commands will place network 10.2.3.0/24 into area 0?

router ospf 10 network 10.2.3.0 0.0.0.255 area 0

Which command is used to determine if an access list is enabled on a particular interface?

show ip interface

Which of the following commands provides the product ID and serial number of a router?

show license udi

If routers in a single area are configured with the same priority value, what value does a router use for the OSPF router ID in the absence of a loopback interface?

The highest IP address of any physical interface

An IPv6 ARP entry is listed as with a status of REACH. What can you conclude about the IPv6-t0-MAC address mapping?

The interface has communicated with the neighbor address and the mapping is current.

Which two statements describe the IP address 10.16.3.65/23?

The lowest host address in the subnet is 10.16.2.1 255.255.254.0 The broadcast address of the subnet is 10.16.3.255 255.255.254.0

What configuration parameters must be configured the same between switches for LACP to form a channel?

Port Speeds, Duplex, and Allowed VLAN information

___ is a Ruby-based configuration management tool that uses custom manifest files to configure devices

Puppet

Which configuration management solution require agents?

Puppet and Chef

You want to use the Command Runner. What is this used for?

Pushing Show commands and viewing the results

You need to look at past network data in DNA Center. How long can you look back into the DNA snapshot?

1 week

How many collision domains are created when you segment a network with a 12-port switch?

12

Each field in an IPv6 address is how many bits long?

16

To enable OSPFv3, which of the following would you use?

Router (config-if)#ipv6 ospf 1- area 0.0.0.0

What does the command routerA(config)#line cons 0 allow you to perform next?

Set your console password

What command is used to view the IPv6-to-MAC-address resolution table on a Cisco?

Show IPv6 neighbors

What protocols are used to configure trunking on a switch?

802.1q ISL

1000Base-T is which IEEE standard?

802.3ab

What class of IP address provides 15 bits for subnetting?

A

What does a VLAN do?

Breaks up broadcast domains in a layer 2 switch internetwork

What DNS record do you need to create for APs to automatically discover the WLC?

CISCO-CAPWAP-CONTROLLER

-- is a Ruby-based configuration management tool that uses cookbooks to apply configuration

Chef

Which of the ff choices best defines a token in Restful API?

How you authenticate to the Restful API service

Which protocol is used to send a destination network unknown message back to originating hosts?

ICMP

Which of the ff statements is true with regard to ISL and 802.1q?

ISL encapsulates the frame with control information; 802.1q inserts a 802.1q field along with tag control information

Which of the ff is considered to be the inside host's address after translation?

Inside Global

What is the sys-id-ext field in a BPDU used for?

It's a 12-bit field inserted into an Ethernet frame to define VLAN's in an STP instance.

What type of switching is done in a network fabric?

Layer 3

Which AP modes serve wireless traffic?

Local FlexConnect

You want to send a console message to a syslog serer, but you only want to send status messages of 3 and lower. Which of the following commands will you use?

Logging trap errors

A host sends a type of NDP message providing the MAC address that was requested. Which type of NDP was sent?

NA

Your boss read about WPA3 and wants you to explain it to him. What replaced the default open authentication with which of the ff enhancements?

OWE

Where is a hub specified in the OSI model?

Physical Layer

Which port does TACACs+ use for accounting?

TCP 49

You reload a router with a configuration register setting of 0x2101. What will the router do when it reloads?

The Router boots the mini-IOS in ROM.

Which of the ff best describes a Resource in Restful API?

The specific path to the resource you're trying to access through the API

You need to connect to remote IPv6 server in your virtual server farm. You can connect the IPv4 servers, but not the IPv6 servers you desperately need. Based on the following output, what could your problem be? C:\>ipconfig Connection-specific DNS Suffix . : localdomain IPv6 Address . . . . . . .. . . . . . .. . .: 2001:db8:3c4d:3:ac3b:2ef:1823:8938 Temporary IPv6 Address. . . .. . : 2001:db8:3c4d:3:2f33:44dd:211:1c3d Link-Local IPv6 Address. . . .. . .: fe80:ac3b:2ef:1823:8938%11 IPv4 Addres . . . .. . .. . . .. . . .. .. . .:10.1.1.10 Subnet Mask . .. . .. . . . .. . . .. . . .. :255.255.255.0 Default Gateway . . .. . .. .. .. .. .. ...: 10.1.1.10

There is no IPv6 default gateway listed

Based on the configuration shown below, what statement is true? S1(config)#ip routing S1(config)#int vlan 10 S1(config-if)#ip address 192.168.10.1 255.255.255.0 S1(config-if)#int vlan 20 S1(config-if)#ip address 192.168.20.1 255.255.255.0

This is a multilayer switch.

Which protocol does DHCP use at the Transport layer?

UDP