Chapter 6,7, and 8 test review Billy Jones!!!!!!
You have a private network connected to the internet. Your routers will not share routing information about your private network with internet routers. Which of the following best describes the type of routing protocol you would use?
IGP
You have a router that is configured as a firewall. The router is a Layer 3 device only. Which of the following does the router use for identifying allowed or denied packets?
IP address
You have a router that is configured as a firewall. The router is a Layer 3 device only. Which of the following does the router use for identifying allowed or denied packets?
IP address
Under which of the following circumstances might you implement BGP on your company network and share routes with Internet routers?
If the network is connected to the Internet using multiple ISPs.
You manage a local area network with several switches. A new employee has started today so you connect her workstation to a switch port. Which of the following is the most likely cause of the problem?
Incorrect VLAN assignment
Which of the following are reasons to configure VLANs on a switch as opposed to using switches without VLANs? Select two
Increased number of broadcast domains Increased security
You would like to control internet access based on users, time of day, and websites visited. How can you do this?
Install a proxy server. Allow internet access only through the proxy server.
A switch running STP is in the listening state. A message destined for a different network segment arrives at the switch. Which of the following best describes what the switch will do?
It does not record address or segment information. It does not forward the message.
A switch is running the STA as the learning starts. A message arrives at the switch destined for a different network segment. Which of the following best describes what the switch will do?
It uses the source mac address and network segment information to build its bridge database, but does not forward the message
Switches running the STP are in the process of exchanging BPDUs and defining their roles. In what state are the switches?
Listening
You manage a network with multiple subnets connected to the internet. A user reports that she can't access the internet. You investigate the problem and find that she can access all hosts on the private network, but no hosts on the internet. Which of the following is likely the cause of the problem?
Missing default route on a router
You need to configure spanning tree on a Cisco switch. You'd like to use a protocol that conforms to the 802.1w standards. Which protocol should you use?
Rapid PVST +
Based on the diagram, which type of proxy server is handling the client's request?
Reverse proxy server
You define VLAN 1 and VLAN 2 on each switch. A device on the first switch in VLAN 1 needs to communicate with a device on the second switch also in VLAN 1. What should you configure to allow communication between these two devices through the switches?
Routing
A switch receives a frame addressed to the MAC address FF:FF:FF:FF:FF:FF. What will the switch do with the frame?
Send it out to all ports except the port it was received on
You are monitoring network traffic on your network, and you see traffic between two network hosts on port 1720. What is the source of this network traffic?
Someone is using voice over IP (VoIP) to make a telephone call.
Which of the following features are common functions of an all-in-one security appliance? Select two
Spam filtering Bandwidth shaping
Which of the following would you implement to eliminate switching loops?
Spanning Tree
Which of the following statements accurately describes a VLAN ID?
Switches append a VLAN ID to the header of each frame to identify the virtual network it belongs to
Which of the following statements describe how VLANs affect broadcast traffic within a network? Select two
Broadcast traffic is transmitted only within a VLAN Devices on the same VLAN have the same subnet address
Which of the following are true about reverse proxy? (Select two.)
Handles requests from the internet to a server in a private network. Can perform load balancing, authentication, and caching.
You have been given a laptop to use for work. You connect the laptop to your company network, use it from home, and use it while traveling. You want to protect the laptop from internet-based attacks. Which solution should you use?
Host-based firewall
You have just installed a packet filtering firewall on your network. Which options will you be able to set on your firewall? (Select all that apply.)
- Destination address of a packet - Port number - Source address of a packet
You have used firewalls to create a demilitarized zone. You have a webs server that needs to be accessible to internet users. The web server must communicate with a database server for retrieving product, customer, and order information. How should you place devices on the network to best protect the servers? (Select two.)
- Put the database server on the private network - Put the web server inside the DMZ.
Which of the following is a characteristic of static routing when compared to dynamic routing?
-All routes must be manually updated on the router.
You want to maintain tight security on your internal network, so you restrict access to the network through certain port numbers. If you want to allow users to use DNS, which port should you enable?
53
Haley configures a website using Windows Server 2016 default values. What are the HTTP port and SSL port settings?
80 for HTTP; 443 for SSL
select the statement that best describes a broadcast storm.
A Broadcast storm occurs when there are so many broadcast messages on the network that they approach or exceed the network bandwidth..
You connect your computer to a wireless network available at the local library. You find that you can access all the websites you want on the internet except for two. What might be causing the problem?
A proxy server is blocking access to the websites.
An all-in-one security appliance is best suited for which type of implementation?
A remote office with no on-site technician.
Which of the following associates a port number with a host on a private network?
PAT
Which of the following is a firewall function?
Packet filtering
You recently installed a new all-in-one security appliance in a remote office. You are in the process of configuring the device. You need to: *Increase the security of the device *Enable remote management from the main office *Allow users to be managed through Active Directory You want to configure the device so you can access it from the main office. You also want to make sure the device is as secure as possible. Which of the following tasks should you carry out?
-Configure the device's authentication type to use Active Directory -Change the default name and password
You have just installed a packet filtering firewall on your network. Which options will you be able to set on your firewall? (Select all that apply.)
-Destination address of a packet -Port number -Source address of a packet
A router is connected to network 192.168.1.0/24 and network 192.168.2.0/24. The router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24. There is no default route configured on the router.
-Drop the packet
A router is connected to network 192.168.1.0/24 and network 192.168.2.0/24. The router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24. The router is also configured with a static route of 0.0.0.0 with a mask of 0.0.0.0.
-Forward the packet to the next hop router specified by the route to the network 0.0.0.0.
Which statements accurately describe the port stages of both Bridges and Switches? select two
-In the learning state, the Mac address table can be opened, but frames are not forwarded; -Ports in a blocked state still receive BPDUs
When multiple routes to a destination exist, what is used to select the best possible route?
-Metric
What info does the next hop entry in a routing table identify.
-The first router in the path to the destination network.
Which of the following tasks do routers perform? (select 2)
-maintain info about paths through internetwork. -route data based on logical network addresses
You have a computer that is connected to the internet through a NAT router. You want to use a private addressing scheme for your computer. Which of the following IP addresses could you assign to the computer? (Select all that apply.)
10.0.12.15 192.168.12.253 172.18.188.67
You have recently installed a new Windows Server 2016 system. To ensure the accuracy of the system time, you have loaded an application that synchronizes the hardware clock on the server with an external time source on the internet. Now, you must configure the firewall on your network to allow time synchronization traffic through. Which of the following ports are you most likely to open on the firewall?
123
Which of the following IP addresses is a valid IP address for a host on a public network?
142.15.6.1
Which of the following is not one of the ranges of IP addresses defined in RFC 1918 that are commonly used behind a NAT server?
169.254.0.1 - 169.254.255.254
You have two switches connected as shown in the following diagram. How many broadcast domains?
2
Which of the following routing protocols uses paths, rules, and policies instead of a metric for making routing decisions?
BGP
A switch running STP is a backup bridge. What state is it in?
Blocking
Which of the following describes how access lists can be used to improve network security?
An access list filters traffic based on the IP header information such as source or destination IP address, protocol, or socket numbers.
Assuming the default configuration, which switch will become the root bridge?
B
Which of the following routing protocols is used by routers on the internet for learning and sharing routes?
BGP
When designing a firewall, what is the recommended approach for opening and closing ports?
Close all ports; open only ports required by applications inside the DMZ.
Match each type of switch on the left with its corresponding characteristics on the right. Each switch type may be used once, more than once, or not at all.
Commonly sold at retail stores. -Unmanaged switch Provides port security features. -Managed switch Supports VLANs. -Managed switch Provides very few configuration options. -Unmanaged switch Can be configured over a network connection. -Managed switch Can be configured over a dedicated communication channel. -Managed switch
Match each switch management method on the left with its corresponding characteristics on the right. Each method may be used once, more than once, or not at all.
Competes with normal network traffic for bandwidth. -In-band management Uses a dedicated communication channel. -Out-of-band management Must be encrypted to protect communications from sniffing. -In-band management Does not compete with normal network traffic for bandwidth. -Out-of-band management Affected by network outages. -In-band management
Computers A and B are on the same VLAN and are separated by two switches, as shown in the exhibit. Computer A sends a Frame to Computer B. Which of the following best describes the composition of the frame as it travels from A to B?
Computer A sends a normal frame. The first switch appends a VLAN ID to the frame. The second switch removes the VLAN ID before forwarding it to computer B
How can you guarantee that switch c becomes the root bridge?
Configure switch c with a lower priority value
What does the ip address dhcp command allow you to do?
Configure the switch to obtain an IP address from a DHCP server.
Match the Cisco device password type on the left with its function on the right.
Controls the ability to log on through a LAN or WAN interface configured on the device. -VTY Controls the ability to connect to the device using a web browser using HTTPS. -SDM Controls the ability to connect to the device using a direct connection. -Console
You have a network configured to use the OSPF routing protocol. Which of the following describes the state when all OSPF routers have learned about all other routes in the network?
Convergence
How can you force switch c to become the root bridge?
Create a priority of 4096 for switch c
You have just connected a new computer to your network. The network uses static IP addressing. You find that the computer can communicate with host on the same subnet, but not with hosts on a different subnet. No other computers are having a problem. Which of the configuration values would you most likely need to change?
Default gateway
Match the EtherChannel protocol on the left with its characteristics on the right. Each protocol may be used once, more than once, or not at all.
Desirable mode places the port in a negotiating state. -Port Aggregation Protocol (PAgP) Based on the 802.3ad standard. -Link Aggregation Control Protocol (LACP) Passive mode places the port into a passive negotiating state. -Link Aggregation Control Protocol (LACP) Auto mode places the port into a passive negotiating state. -Port Aggregation Protocol (PAgP) Active mode places the port in a negotiating state. -Link Aggregation Control Protocol (LACP)
Which of the following best describes the concept of a VLAN?
Devices on the same network logically grouped as if they were on separate networks
In the output of the netstat command, you notice that a remote system has made a connection to your Windows Server 2016 system using TCP/IP port 21. Which of the following actions is the remote system most likely performing?
Downloading a file
A user reports that network access from her workstation is very slow. The problem does not seem to be affecting any other users. Which of the following conditions is the most likely cause?
Duplex mismatch
You want to connect your small company network to the internet. Your ISP provides you with a single IP address that is to be shared between all hosts on your private network. You do not want external hosts to be able to initiate connections to internal hosts. What type of network address translation (NAT) should you implement?
Dynamic
Which of the following routing protocols is classified as a hybrid routing protocol?
EIGRP
You manage a network with multiple switches. You find that your switches are experiencing heavy broadcast storms. Which of the following will help reduce the effects of a broadcast storm?
Enable spanning tree on the switches
You need to disable the FastEthernet 0/0 interface on a switch. Drag the command on the left to the appropriate configuration step on the right. It is possible that not all of the commands are required.
Enter global configuration mode. conf t Enter interface configuration mode. int fa0/0 Disable the interface. shutdown Verify that the interface is disabled. show ip interface brief
The FastEthernet 0/0 interface on a switch is currently disabled. You need to enable it so a workstation can be connected to it. Drag the command on the left to the appropriate configuration step on the right. It is possible that not all commands are required.
Enter global configuration mode. conf t Enter interface configuration mode. int fa0/0 Enable the interface. no shut Verify that the interface is enabled. show interface status
You need to configure the FastEthernet 0/1 interface on a switch to automatically detect the appropriate link speed and duplex setting by negotiating with the device connected to the other end of the link. Drag the command on the left to the appropriate configuration step on the right. It is possible that not all of the commands are required.
Enter global configuration mode. conf t Enter interface configuration mode. int fa0/1 Set the speed of the interface. speed auto Set the duplex setting for the interface. duplex auto
You want to allow users to download files from a server running the TCP/IP Protocol. You want to require user authentication to gain access to specific directories on the server. Which TCP/IP protocol should you implement to provide this capability?
FTP
Which of the following is likely to be located in a DMZ?
FTP server
You manage a network with multiple subnets connected to the internet. A user reports that she can't access the new server used in the accounting department. You check the problem and find out that her computer cannot access any server on that subnet. However, the computer does access other computers on other subnets as well as the internet. Which of the following is most likely the cause of the problem?
Missing route on the default gateway router
Your company has a connection to the internet that allows users to access the internet. You also have a web server and an email server that you want to make available to internet users. You want to create a DMZ for these two servers. Which type of device should you use to create the DMZ?
Network-based firewall
You are configuring a switch so that you can manage it using PUTTY. Will this configuration work?
No, the shutdown command needs to be entered
Which of the following routing protocols divides the network into areas, with all networks required to have an area 0 (area 0 identifying the backbone area)?
OSPF
Which of the following routing protocols uses relative link cost as the metric?
OSPF
Which of the following best describes OSPF?
OSPF is a classless link state routing protocol.
What are the main differences between the OSPF and IS-IS routing protocols?
OSPF requires an area 0, while IS-IS does not.
To test this theory, you enter the ping FS23 -f -l 1500 command on your workstation. The ping command returns the following command for each ping packet sent: "Packet needs to be fragmented but DF set" What does this mean?
One of the intermediate routers is an MTU black hole.
After blocking a number of ports to secure your server, you are unable to send email. To allow email service, which of the following needs to be done?
Open port 25 to allow SMTP service.
Match the firewall type on the left with its associated characteristics on the right. Each firewall type may be used once, more than once, or not at all.
Operates at Layer 2 - Virtual firewall Operates at Layer 3 - Routed firewall Counts as a hop in the path between hosts. - Routed firewall Does not count as a hop in the path between hosts. - Virtual firewall Each interface connects to a different network. - Routed firewall Each interface connects to the same network segment. - Virtual firewall
Match the firewall type on the right with the OSI layer at which it operates. Each OSI Layer may be used once, more than once, or not at all.
Packet filtering firewall - OSI Layer 3 Circuit-level proxy - OSI Layer 5 Application-level gateway - OSI Layer 7 Routed firewall - OSI Layer 3 Transparent firewall - OSI Layer 2
Which of the following techniques allows incoming traffic addressed to a specific port to move through a NAT router and be forwarded to a specific host?
Port forwarding
You have a small network at home that is connected to the internet. On your home network, you have a server with the IP address of 192.168.55.199/16. All computers on your home network can connect to the internet. From your work office, you try to access your home computer using its IP address, but are unable to communicate with the server. You are able to connect to other hosts on the internet. Why can't you access the server?
Private addresses are not accessible through the internet
Your computer has an IP address of 161.13.5.15. Your computer is on a:
Public Network
Which of the following protocols has a limit of 15 hops between any two networks?
RIP
Which of the following statements about RIP is true?
RIP uses hop counts as the cost metric.
Which dynamically places switch ports in blocking or forwarding states?
Spanning tree
You manage a network that uses multiple switches. You want to provide multiple paths between switches so that if one link goes down, an alternate path is available. Which feature should your switch support?
Spanning tree
You manage a single subnet with three switches. The switches are connected to provide redundant paths between the switches. Which feature prevents switching loops and ensures there is only a single active path between any two switches?
Spanning tree
Which of the following are characteristics of a circuit-level gateway? (Select two.)
Stateful Filters by session
You are the network administrator for a small company that implements NAT to access the internet. You recently acquired five servers that must be accessible from outside your network. Your ISP has provided you with five additional registered IP addresses to support these new servers, but you don't want the public to access these servers directly. You want to place these servers behind your firewall on the inside network, yet still allow them to be accessible to the public from the outside. Which method of NAT translation should you implement for these five servers?
Static
You have a small network at home that is connected to the internet. On your home network, you have a server with the IP address of 192.168.55.199/16. You have a single public address that is shared by all hosts on your private network. You want to configure the server as a web server and allow internet hosts to contact the server to browse a personal website. What should you use to allow access?
Static NAT
Which of the following connectivity hardware is used to create a VLAN?
Switch
You can create a vlan using which of the following?
Switch
You want to reduce collisions by creating separate collision domains and virtual LANs. Which of the following devices should you choose?
Switch
When you configure VLANS on a switch, which of the following is used to identify a device's VLAN membership?
Switch Port
You administer a web server on your network. The computer has multiple IP addresses. They are 192.168.23.8 to 192.168.23.17. The name of the computer is www.westsim.com. You configured the website as follows: Users complain that they can't connect to the website when they type www.westsim.com. What is the most likely source of the problem?
The HTTP port should be changed to 80.
Which kind of network traffic uses this port?
The MGCP protocol is generating traffic, which VoIP uses to send voice data over a network.
Which of the following are true regarding using multiple VLANs on one switch? Select two
The number of broadcast domains increases the number of collision domains remains the same
While viewing the status of the interfaces on a Cisco switch, you see abnormally large or oversized ethernet frames being received on one interface. This interface is connected to a workstation located on the 2nd floor. What could be causing this to happen?
The workstation's network board is jabbering
When configuring VLANs on a switch, what type of switch ports are members of all VLANs defined on the switch?
Trunk Ports
You manage a network with two switches. The switches are connected together using their Gigabit ethernet uplink ports. You define vlan1 and vlan2 on each switch. A device on the first switch needs to communicate with a device on the second switch in vlan1. What should you configure?
Trunking
You manage a single subnet with three switches. The switches are connected to provide redundant paths between the switches. Which feature allows the switches to pass VLAN traffic between the switches?
Trunking
You run a small network for your business that has a single router connected to the Internet and a single switch. You keep sensitive documents on a computer that you would like to keep isolated from other computers on the network. Other hosts on the network should not be able to communicate with this computer through the switch, but you still need to access the network through the computer. What should you use for this situation?
VLAN
You run a small network for your business that has a single router connected to the internet and a single switch. You keep a sensitive doc. What should you use for this situation?
VLAN
You would like to make sure your computers are isolated from computers used by other companies. Which feature should you request be implemented?
VLAN
In the lobby of your building there are three rj45 ports connected to the switch. You want to allow visitors to plug into these ports to gain internet access, but they should not have access to other devices on your private network. Employees connected throughout the rest of your building should have both private and internet access. Which feature should you implement?
VLANs
You manage a network that uses a single switch. All ports within your buildings connect through a single switch . Which feature should you implement?
VLANs
You need to keep all users in other departments from accessing the servers used by the finance department. Which of these technologies should you use to logically isolate the network?
VLANs
Which of the following are true of a circuit proxy filter firewall? (Select two.)
Verifies sequencing of session packets. Operates at the Session layer.
A router is connected to network 192.168.1.0/24 and network 192.168.2.0/24. The router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24. The next hop router for network 192.168.3.0 has changed. You need to make the change with the least amount of effort possible. What should you do?
Wait for convergence to take place.
You are configuring a firewall to allow access to a server hosted on the demilitarized zone of your network. You open TCP/IP ports 80, 25, 110, and 143. Assuming that no other ports on the firewall need to be configured to provide access, which applications are most likely to be hosted on the server?
Web server and email server
Which of the following benefits apply to only creating VLANs with switches and not to segmenting the network with regular switches.
You can create multiple broadcast domains
In which of the following situations would you most likely implement a demilitarized zone (DMZ)?
You want to protect a public web server from attack.
You manage a network with a single switch. On each switch port, a hub connects multiple devices to the switch. Which condition are you most likely to experience on the network ?
collisions
Which command would you use on a switch to enable management from a remote network?
ip default-gateway 192.168.10.185
Which of the following utilities would you use to view the routing table?
route
Which of the following commands would display the output shown here?
route print
The network board in a workstation is currently configured as follows:
show running-config interface show interface
Examine the following output: 4 22 ms 21 ms 22 ms sttlwa01gr02.bb.ispxy.com [154.11.10.62] 5 39 ms 39 ms 65 ms plalca01gr00.bb.ispxy.com [154.11.12.11] 6 39 ms 39 ms 39 ms Rwest.plalca01gr00.bb.ispxy.com [154.11.3.14] 7 40 ms 39 ms 46 ms svl-core-03.inet.ispxy.net [205.171.205.29] 8 75 ms 117 ms 63 ms dia-core-01.inet.ispxy.net [205.171.142.1] Which of these commands produced this output?
tracert
What TCP/IP utility can you use to see if a router is working properly?
tracert
Which TCP/IP utility gives you the following output?
tracert
