Cisco 3
Refer to the exhibit. Which route or routes will be advertised to the router ISP if autosummarization is enabled? 10.0.0.0/8 10.1.0.0/16 10.1.0.0/28 10.1.1.0/24 10.1.2.0/24 10.1.3.0/24 10.1.4.0/28
10.0.0.0/8*
If a company wants to upgrade a Cisco 2800 router from IOS 12.4T, what IOS should be recommended for a stable router platform? 13.1T 12.5T 15.1M 14.0
15.1M *
By default, how many equal cost routes to the same destination can be installed in the routing table of a Cisco router? 2 4 16 32
4
A set of switches is being connected in a LAN topology. Which STP bridge priority value will make it least likely for the switch to be selected as the root? 4096 32768 61440 65535
61440
Fill in the blank. Use the acronym. Which encryption protocol is used by the WPA2 shared key authentication technique?
AES
Which wireless network topology is being configured by a technician who is installing a keyboard, a mouse, and headphones, each of which uses Bluetooth? ad hoc mode hotspot infrastructure mode mixed mode
Ad hoc mode
A remote classroom can successfully access video-intensive streaming lectures via wired computers. However, when an 802.11n wireless access point is installed and used with 25 wireless laptops to access the same lectures, poor audio and video quality is experienced. Which wireless solution would improve the performance for the laptops? Decrease the power of the wireless transmitter. Add another access point. Upgrade the access point to one that can route. Adjust the wireless NICs in the laptops to operate at 10GHz to be compatible with 802.11n.
Add another access point
What are two requirements to be able to configure an EtherChannel between two switches? (Choose two.) The interfaces that are involved need to be contiguous on the switch. All the interfaces need to work at the same speed. All the interfaces need to be working in the same duplex mode. All interfaces need to be assigned to different VLANs. Different allowed ranges of VLANs must exist on each end.
All the interfaces need to work at the same speed.* All the interfaces need to be working in the same duplex mode.*
Refer to the exhibit. What are the possible port roles for ports A, B, C, and D in this RSTP-enabled network? alternate, root, designated, root designated, root, alternate, root alternate, designated, root, root* designated, alternate, root, root
Alternate, designated, root, root
A network administrator enters the spanning-tree portfast bpduguard default command. What is the result of this command being issued on a Cisco switch? Any switch port will be error-disabled if it receives a BPDU. Any trunk ports will be allowed to connect to the network immediately, rather than waiting to converge. Any switch port that has been configured with PortFast will be error-disabled if it receives a BPDU. Any switch port that receives a BPDU will ignore the BPDU message.
Any switch port that has been configured with PortFast will be error-disabled if it receives a BPDU.*
Refer to the exhibit. If router B is to be configured for EIGRP AS 100, which configuration must be entered? B(config-router)# network 192.168.10.4 0.0.0.3 B(config-router)# network 192.168.10.8 0.0.0.3 B(config-router)# network 192.168.10.4 0.0.0.3 B(config-router)# network 192.168.10.8 0.0.0.3 B(config-router)#network 192.168.10.128 0.0.0.63 B(config-router)# network 192.168.10.4 255.255.255.248 B(config-router)# network 192.168.10.8 255.255.255.248 B(config-router)#network 192.168.10.128 255.255.255.192 B(config-router)# network 192.168.10.0 255.255.255.0 B(config-router)# network 192.168.10.4 0.0.0.3 B(config-router)# network 192.168.10.8 0.0.0.3 B(config-router)# network 192.168.10.64 0.0.0.63 B(config-router)# network 192.168.10.128 0.0.0.63 B(config-router)# network 192.168.10.192 0.0.0.63 B(config-router)# network 192.168.10.0 0.0.0.255
B(config-router)# network 192.168.10.4 0.0.0.3 B(config-router)# network 192.168.10.8 0.0.0.3 B(config-router)#network 192.168.10.128 0.0.0.63*
The " _________________ " area interconnects with all other OSPF area types.
Backbone
A WLAN user wants to allocate an optimal amount of bandwidth to a specific online game. What is a Linksys Smart Wi-Fi tool that will allow the user to do this? Widgets Speed Test Media Prioritization Bandwidth Prioritization
Bandwidth Prioritization*
What are two drawbacks to turning spanning tree off and having multiple paths through the Layer 2 switch network? (Choose two.) Broadcast frames are transmitted indefinitely.* Port security shuts down all of the port that attached devices. The switch acts like a hub. The Mac address table becomes unstable.* Port security becomes unstable.
Broadcast frames are transmitted indefinitely.* The Mac address table becomes unstable.*
What two conditions have to be met in order to form a cluster that includes 5 access points? (Choose two.) Clustering mode must be enabled on the APs. At least two controllers are needed to form the cluster. The APs have to be connected on the same network segment. The APs must all be configured to use different radio modes. The APs must use different cluster names.
Clustering mode must be enabled on the APs.* The APs have to be connected on the same network segment.*
Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency. What action should be taken to solve this problem? Enable the serial interfaces of both routers. Configure EIGRP to send periodic updates. Configure the same hello interval between the routers. Configure both routers with the same EIGRP process ID.
Configure both routers with the same EIGRP process ID.*
Which function is provided by EtherChannel? spreading traffic across multiple physical WAN links dividing the bandwidth of a single link into separate time slots enabling traffic from multiple VLANs to travel over a single Layer 2 link creating one logical link by using multiple physical links between two LAN switches
Creating one logical link by using multiple physical links between two LAN switches
Which two channel group modes would place an interface in a negotiating state using PAgP? (Choose two.) on desirable active auto passive
Desirable Auto
A network engineer is troubleshooting a single-area OSPFv3 implementation across routers R1, R2, and R3. During the verification of the implementation, it is noted that the routing tables on R1 and R2 do not include the entry for a remote LAN on R3. Examination of R3 shows the following: 1.that all interfaces have correct addressing 2.that the routing process has been globally configured 3.that correct router adjacencies have formed What additional action taken on R3 could solve the problem? Enable the OSPFv3 routing process on the interface connected to the remote LAN. Use the network command to configure the LAN network under the global routing process. Force DR/BDR elections to occur where required. Restart the OPSFv3 routing process.
Enable the OSPFv3 routing process on the interface connected to the remote LAN.*
A network administrator is analyzing the features that are supported by different first-hop router redundancy protocols. Which statement is a feature that is associated with GLBP? GLBP allows load balancing between routers. It is nonproprietary. It uses a virtual router master. It works together with VRRP.
GLBP allows load balancing between routers.*
A network engineer is configuring a LAN with a redundant first hop to make better use of the available network resources. Which protocol should the engineer implement? FHRP VRRP GLBP HSRP
GLBP*
A network administrator is analyzing the features that are supported by different first-hop router redundancy protocols. Which statement describes a feature that is associated with HSRP? HSRP uses active and standby routers. It uses ICMP messages in order to assign the default gateway to hosts. It allows load balancing between a group of redundant routers. HSRP is nonproprietary.
HSRP uses active and standby routers.
A network administrator is analyzing first -hop router redundancy protocols.What is characteristic of VRRPv3. characteristics of VRRPV3: INTEROPERABILITY IN MULTI-VENDOR ENVIRONMENTS* VRRPv3 SUPPORTS USAGE OF IPv4 and IPv6* IMPROVE SCALABILITY THROUGH USE OF VRRS PATHWAYS* so judging from the options given it will be supports both IPv6 and IPv4 addressing
INTEROPERABILITY IN MULTI-VENDOR ENVIRONMENTS* VRRPv3 SUPPORTS USAGE OF IPv4 and IPv6* IMPROVE SCALABILITY THROUGH USE OF VRRS PATHWAYS*
Which Cisco IOS Software Release 15.0 technology pack is shipped with a permanent license on all Cisco ISR G2 devices? IPBase DATA Unified Communications Security
IPBase*
What occurs when authentication is configured on an EIGRP router? After EIGRP authentication has been configured, the router must be rebooted to be able to reestablish adjacencies. If adjacencies are displayed after the use of the show ipv6 eigrp neighbors command, then EIGRP authentication was successful. Only one router is required to be configured for EIGRP authentication. If only one router has been configured for EIGRP authentication, any prior adjacencies will remain intact.
If adjacencies are displayed after the use of the show ipv6 eigrp neighbors command, then EIGRP authentication was successful.*
Match the OSPF router type description with its name Internal routers: Routers that have all their interfaces in the same area and have identical LSDBs. Area border routers: All the routers of this type maintain separate LSDBs for each area to which they connect. Autonomous System Boundary Routers: Routers that have at least one interface attached to an external internetwork (another autonomous system), such as a non-OSPF network.
Internal routers: Routers that have all their interfaces in the same area and have identical LSDBs. Area border routers: All the routers of this type maintain separate LSDBs for each area to which they connect. Autonomous System Boundary Routers: Routers that have at least one interface attached to an external internetwork (another autonomous system), such as a non-OSPF network.
What is the function of STP in a scalable network? It combines multiple switch trunk links to act as one logical link for increased bandwidth. It decreases the size of the failure domain to contain the impact of failures. It protects the edge of the enterprise network from malicious activity. It disables redundant paths to eliminate Layer 2 loops.
It disables redundant paths to eliminate Layer 2 loops.*
What is the purpose of the Cisco PAK? It is a key for enabling an IOS feature set. It is a proprietary encryption algorithm. It is a compression file type used when installing IOS 15 or an IOS upgrade. It is a way to compress an existing IOS so that a newer IOS version can be co-installed on a router.
It is a key for enabling an IOS feature set.*
What is the purpose of a Cisco IOS 15 EM release? It specifies advanced IP services features such as advanced security and service provider packages. It provides regular bug fix maintenance rebuilds, plus critical fix support for network-affecting bugs. It is used for long-term maintenance, enabling customers to qualify, deploy, and remain on the release for an extended period. It provides premium packages and enables additional IOS software feature combinations that address more complex network requirements.
It is used for long-term maintenance, enabling customers to qualify, deploy, and remain on the release for an extended period.*
A network administrator is analyzing first-hop router redundancy protocols. What is a characteristic of VRRPv3? VRRPv3 is Cisco proprietary. It supports IPv6 and IPv4 addressing. It allows load balancing between routers. It works together with HSRP.
It supports IPv6 and IPv4 addressing.*
Which technology is an open protocol standard that allows switches to automatically bundle physical ports into a single logical link? Multilink PPP PAgP DTP LACP
LACP*
What two license states would be expected on a new Cisco router once the license has been activated? (Choose two.) License Type: ipbasek9 License Type: Permanent License Type: Temporary License State: Active, In Use License State: Active, Registered License State: On
License Type: Permanent* License State: Active, In Use*
Refer to the exhibit. Which destination MAC address is used when frames are sent from the workstation to the default gateway? MAC address of the forwarding router MAC addresses of both the forwarding and standby routers MAC address of the standby router MAC address of the virtual router
MAC address is the virtual router
What is a wireless modulation technique used by 802.11 WLAN standards that can implement MIMO? FHSS OFDM BSS DSSS
OFDM*
At a local college, students are allowed to connect to the wireless network without using a password. Which mode is the access point using? network open passive shared-key
Open
Refer to the exhibit. A network administrator is attempting to upgrade the IOS system image on a Cisco 2901 router. After the new image has been downloaded and copied to the TFTP server, what command should be issued on the router before the IOS system image is upgraded on the router? ping 10.10.10.1 dir flash: ping 10.10.10.2 copy tftp: flash0:
Ping 10.10.10.2
Refer to the exhibit. What two pieces of information could be determined by a network administrator from this output? (Choose two.) The metric that will be installed in the routing table for the 10.0.0.0 route will be 65 (64+1). Interface Fa0/1 is not participating in the OSPF process. R1 is the distribution point for the routers that are attached to the 10.0.0.4 network. R1 is participating in multiarea OSPF. The OSPF process number that is being used is 0.
R1 is the distribution point for the routers that are attached to the 10.0.0.4 network.* R1 is participating in multiarea OSPF.*
Refer to the exhibit. When the show ip ospf neighbor command is given from the R1# prompt, no output is shown. However, when the show ip interface brief command is given, all interfaces are showing up and up. What is the most likely problem? R2 has not brought the S0/0/1 interface up yet. R1 or R2 does not have a loopback interface that is configured yet. The ISP has not configured a static route for the ABC Company yet. R1 or R2 does not have a network statement for the 172.16.100.0 network. R1 has not sent a default route down to R2 by using the default-information originate command.
R1 or R2 does not have a network statement for the 172.16.100.0 network.*
An STP instance has failed and frames are flooding the network. What action should be taken by the network administrator? Broadcast traffic should be investigated and eliminated from the network. Spanning tree should be disabled for that STP instance until the problem is located. Redundant links should be physically removed until the STP instance is repaired. A response from the network administrator is not required because the TTL field will eventually stop the frames from flooding the network.
Redundant links should be physically removed until the STP instance is repaired.*
A router has been removed from the network for maintenance. A new Cisco IOS software image has been successfully downloaded to a server and copied into the flash of the router. What should be done before placing the router back into service? Delete the previous version of the Cisco IOS software from flash. Copy the running configuration to NVRAM. Back up the new image. Restart the router and verify that the new image starts successfully.
Restart the router and verify that the new image starts successfully.*
Match the CLI command prompt with the command or response entered when backing up a Release 15 IOS image to an IPv6 TFTP server. (Not all options are used.) RouterA# -> copy flash0:tftp: Source Filename? -> C1900-universalk9-m.SPA.152-4.M3.bin Address or name of remote host ->2001:DB8:CAFE:100::9
RouterA# -> copy flash0:tftp: Source Filename? -> C1900-universalk9-m.SPA.152-4.M3.bin Address or name of remote host ->2001:DB8:CAFE:100::9
What are two features of OSPF interarea route summarization? (Choose two.) ASBRs perform all OSPF summarization. Routes within an area are summarized by the ABR. ABRs advertise the summarized routes into the backbone. Type 3 and type 5 LSAs are used to propagate summarized routes by default. Route summarization results in high network traffic and router overhead.
Routes within an area are summarized by the ABR.* ABRs advertise the summarized routes into the backbone.*
Refer to the exhibit. What are two results of issuing the displayed commands on S1, S2, and S3? (Choose two.) S3 can be elected as a secondary bridge. S2 can become root bridge if S3 fails. S1 will automatically adjust the priority to be the lowest. S2 can become root bridge if S1 fails. S1 will automatically adjust the priority to be the highest.
S1 will automatically adjust the priority to be the lowest.* S2 can become root bridge if S1 fails.*
Refer to the exhibit. Which switch will be the root bridge after the election process is complete? S1 S2 S3 S4
S2
Refer to the exhibit. A network administrator is configuring PVST+ for the three switches. What will be a result of entering these commands? S1 will set the priority value for VLAN 10 to 0. S2 will set the priority value for VLAN 10 to 24576. S3 will set the priority value for VLAN 30 to 8192. S1 will set the priority value for VLAN 20 to 24596.
S3 will set the priority value for VLAN 30 to 8192
Which mode configuration setting would allow formation of an EtherChannel link between switches SW1 and SW2 without sending negotiation traffic? SW1: on SW2: on SW1: desirable SW2: desirable SW1: auto SW2: auto trunking enabled on both switches SW1: auto SW2: auto PortFast enabled on both switches SW1: passive SW2: active
SW1: on SW2: on*
Users on an IEEE 801.11n network are complaining of slow speeds. The network administrator checks the AP and verifies it is operating properly. What can be done to improve the wireless performance in the network? Split the wireless traffic between the 802.11n 2.4 GHz band and the 5 GHz band. Change the authentication method on the AP. Switch to an 802.11g AP. Set the AP to mixed mode.
Split the wireless traffic between the 802.11n 2.4 GHz band and the 5 GHz band.*
A network engineer is troubleshooting a newly deployed wireless network that is using the latest 802.11 standards. When users access high bandwidth services such as streaming video, the wireless network performance is poor. To improve performance the network engineer decides to configure a 5 Ghz frequency band SSID and train users to use that SSID for streaming media services. Why might this solution improve the wireless network performance for that type of service? Requiring the users to switch to the 5 GHz band for streaming media is inconvenient and will result in fewer users accessing these services. The 5 GHz band has a greater range and is therefore likely to be interference-free. The 5 GHz band has more channels and is less crowded than the 2.4 GHz band, which makes it more suited to streaming multimedia. The only users that can switch to the 5 GHz band will be those with the latest wireless NICs, which will reduce usage.
The 5 GHz band has more channels and is less crowded than the 2.4 GHz band, which makes it more suited to streaming multimedia. *
Refer to the exhibit. Why did R1 and R2 not establish ad adjacency? The link-local address must be the same on both routers. The AS number must be the same on R1 and R2.* R1 S0/0/0 and R2 S0/0/0 are on different networks. The no shutdown command is misapplied on both routers. The router ID must be the same on both routers.
The AS number must be the same on R1 and R2.*
Refer to the exhibit. Which two conclusions can be drawn from the output? (Choose two.) The EtherChannel is down. The port channel ID is 2. The port channel is a Layer 3 channel. The bundle is fully operational. The load-balancing method used is source port to destination port.
The EtherChannel is down.* The port channel ID is 2.*
Refer to the exhibit. Based on the command output shown, what is the status of the EtherChannel? The EtherChannel is dynamic and is using ports Fa0/10 and Fa0/11 as passive ports. The EtherChannel is in use and functional as indicated by the SU and P flags in the command output. The EtherChannel is down as evidenced by the protocol field being empty. The EtherChannel is partially functional as indicated by the P flags for the FastEthernet ports.
The EtherChannel is in use and functional as indicated by the SU and P flags in the command output.*
A network administrator has configured an EtherChannel between two switches that are connected via four trunk links. If the physical interface for one of the trunk links changes to a down state, what happens to the EtherChannel? Spanning Tree Protocol will recalculate the remaining trunk links. The EtherChannel will remain functional. The EtherChannel will transition to a down state. Spanning Tree Protocol will transition the failed physical interface into forwarding mode.
The EtherChannel will remain functional.*
A network administrator issues the command R1(config)# license boot module c1900 technology-package securityk9 on a router. What is the effect of this command? The IOS will prompt the user to reboot the router. The features in the Security package are available immediately. The IOS will prompt the user to provide a UDI in order to activate the license. The Evaluation Right-To-Use license for the Security technology package is activated.
The Evaluation Right-To-Use license for the Security technology package is activated.*
What are two differences between the Cisco IOS 12 and IOS 15 versions? (Choose two.) Every Cisco ISR G2 platform router includes a universal image in the IOS 12 versions, but not the IOS 15 versions. The IOS version 15 license key is unique to each device, whereas the IOS version 12 license key is not device specific. The IOS 12 version has two trains that occur simultaneously, whereas the IOS 15 version still has two trains, but the versions occur in a single sequential order. The IOS 12 version has commands that are not available in the 15 version. IOS version 12.4(20)T1 is a mainline release, whereas IOS version 15.1(1)T1 is a new feature release.
The IOS version 15 license key is unique to each device, whereas the IOS version 12 license key is not device specific. IOS version 12.4(20)T1 is a mainline release, whereas IOS version 15.1(1)T1 is a new feature release.
An EIGRP router loses the route to a network. Its topology table contains two feasible successors to the same network. What action will the router take? The router will query neighbors for an alternate route. The router uses the default route. The DUAL algorithm is recomputed to find an alternate route. The best alternative backup route is immediately inserted into the routing table.
The best alternative backup route is immediately inserted into the routing table.*
A network designer is considering whether to implement a switch block on the company network. What is the primary advantage of deploying a switch block? A single core router provides all the routing between VLANs. The failure of a switch block will not impact all end users. This is a security feature that is available on all new Catalyst switches. This is network application software that prevents the failure of a single network device.
The failure of a switch block will not impact all end users.*
Which address is used by an IPv6 EIGRP router as the source for hello messages? the interface IPv6 link-local address the 32-bit router ID the all-EIGRP-routers multicast address the IPv6 global unicast address that is configured on the interface
The interface IPv6 local-link address
Refer to the exhibit. A network administrator issues the show ipv6 eigrp neighbors command. Which conclusion can be drawn based on the output? The link-local addresses of neighbor routers interfaces are configured manually. If R1 does not receive a hello packet from the neighbor with the link-local address FE80::5 in 2 seconds, it will declare the neighbor router is down. R1 has two neighbors. They connect to R1 through their S0/0/0 and S0/0/1 interfaces. The neighbor with the link-local address FE80::5 is the first EIGRP neighbor that is learned by R1.
The link-local addresses of neighbor routers interfaces are configured manually.*
Refer to the exhibit. A network administrator issues the show ipv6 eigrp neighbors command. Which conclusion can be drawn based on the output? The link-local addresses of neighbor routers interfaces are configured manually. R1 has two neighbors. They connect to R1 through their S0/0/0 and S0/0/1 interfaces. The neighbor with the link-local address FE80::5 is the first EIGRP neighbor that is learned by R1. If R1 does not receive a hello packet from the neighbor with the link-local address FE80::5 in 2 seconds, it will declare the neighbor router is down.
The link-local addresses of neighbor routers interfaces are configured manually.*
Which two statements are correct about EIGRP acknowledgment packets? (Choose two.) The packets are sent in response to hello packets. The packets are used to discover neighbors that are connected on an interface. The packets are sent as unicast. The packets require confirmation. The packets are unreliable.
The packets are sent as unicast.* The packets are unreliable.*
What is a requirement to configure a trunking EtherChannel between two switches? The participating interfaces must be on the same module on a switch. The participating interfaces must be physically contiguous on a switch. The participating interfaces must be assigned the same VLAN number on both switches. The allowed range of VLANs must be the same on both switches.
The participating interfaces must be assigned the same VLAN number on both switches.*
Refer to the exhibit. A company has migrated from single area OSPF to multiarea. However, none of the users from network 192.168.1.0/24 in the new area can be reached by anyone in the Branch1 office. From the output in the exhibit, what is the problem? There are no interarea routes in the routing table for network 192.168.1.0. The OSPF routing process is inactive. The link to the new area is down. The router has not established any adjacencies with other OSPF routers.
There are no interarea routes in the routing table for network 192.168.1.0.*
Refer to the exhibit. A network technician is troubleshooting missing OSPFv3 routes on a router. What is the cause of the problem based on the command output? There is a problem with the OSPFv3 adjacency between the local router and the router that is using the neighbor ID 2.2.2.2. The local router has formed complete neighbor adjacencies, but must be in a 2WAY state for the router databases to be fully synchronized. The dead time must be higher than 30 for all routers to form neighbor adjacencies. The neighbor IDs are incorrect. The interfaces must use only IPv6 addresses to ensure fully synchronized routing databases.
There is a problem with the OSPFv3 adjacency between the local router and the router that is using the neighbor ID 2.2.2.2.*
Refer to the exhibit. Which two conclusions can be derived from the output? (Choose two.) There is one feasible successor to network 192.168.1.8/30. The network 192.168.10.8/30 can be reached through 192.168.11.1. The reported distance to network 192.168.1.0/24 is 41024256. The neighbor 172.16.6.1 meets the feasibility condition to reach the 192.168.1.0/24 network. Router R1 has two successors to the 172.16.3.0/24 network.
There is one feasible successor to network 192.168.1.8/30. The neighbor 172.16.6.1 meets the feasibility condition to reach the 192.168.1.0/24 network.
Refer to the exhibit. Which two conclusions can be derived from the output? (Choose two.) The network 192.168.10.8/30 can be reached through 192.168.11.1. The reported distance to network 192.168.1.0/24 is 41024256. Router R1 has two successors to the 172.16.3.0/24 network. There is one feasible successor to network 192.168.1.8/30. The neighbor 172.16.6.1 meets the feasibility condition to reach the 192.168.1.0/24 network.
There is one feasible successor to network 192.168.1.8/30.* The neighbor 172.16.6.1 meets the feasibility condition to reach the 192.168.1.0/24 network.*
Which requirement should be checked before a network administrator performs an IOS image upgrade on a router? The FTP server is operational. The old IOS image file has been deleted. There is sufficient space in flash memory. The desired IOS image file has been downloaded to the router.
There is sufficient space in flash memory.*
A network administrator is troubleshooting slow performance in a Layer 2 switched network. Upon examining the IP header, the administrator notices that the TTL value is not decreasing. Why is the TTL value not decreasing? This is the normal behavior for a Layer 2 network. The VLAN database is corrupt. The MAC address table is full. The inbound interface is set for half duplex.
This is the normal behavior for a Layer 2 network.*
Refer to the exhibit. What can be concluded about network 192.168.1.0 in the R2 routing table? This network has been learned from an internal router within the same area. This network was learned through summary LSAs from an ABR. This network is directly connected to the interface GigabitEthernet0/0. This network should be used to forward traffic toward external networks.
This network was learned through summary LSAs from an ABR.*
Match each OSPF LSA description with its type. (Not all options are used.) This type of LSA exists in multi-access & non-broadcast multi-access networks w/DR => TYPE 2 LSA This type of LSA describes routes to networks outside of the OSPF AS => TYPE 5 LSA This type of LSA is flooded only within the area which it originated => TYPE 1 LSA This type of LSA is used by ABR to advertise networks from other areas => TYPE 3 LSA
This type of LSA exists in multi-access & non-broadcast multi-access networks w/DR => TYPE 2 LSA This type of LSA describes routes to networks outside of the OSPF AS => TYPE 5 LSA This type of LSA is flooded only within the area which it originated => TYPE 1 LSA This type of LSA is used by ABR to advertise networks from other areas => TYPE 3 LSA
Refer to the exhibit. Interface FastEthernet 0/1 on S1 is connected to Interface FastEthernet 0/1 on S2, and Interface FastEthernet 0/2 on S1 is connected to Interface FastEthernet 0/2 on S2. What are two errors in the present EtherChannel configurations? (Choose two.) Desirable mode is not compatible with on mode. The trunk mode is not allowed for EtherChannel bundles. Two auto modes cannot form a bundle. The channel group is inconsistent. The interface port channel ID should be different in both switches.
Two auto modes cannot form a bundle.* The channel group is inconsistent.*
Which type of OSPF LSA represents an external route and is propagated across the entire OSPF domain? type 1 type 2 type 3 type 4 type 5
Type 5
What are two methods to make the OSPF routing protocol more secure? (Choose two.) Use only OSPFv3. Use MD5 authentication. Use the enable secret command. When feasible, create a VPN tunnel between each OSPF neighbor adjacency. Use the passive-interface command on LAN interfaces that are connected only to end-user devices.
Use MD5 authentication.* Use the passive-interface command on LAN interfaces that are connected only to end-user devices.*
Which two conditions should the network administrator verify before attempting to upgrade a Cisco IOS image using a TFTP server? (Choose two.) Verify the name of the TFTP server using the show hosts command. Verify that the TFTP server is running using the tftpdnld command. Verify that the checksum for the image is valid using the show version command. Verify connectivity between the router and TFTP server using the ping command. Verify that there is enough flash memory for the new Cisco IOS image using the show flash command.
Verify connectivity between the router and TFTP server using the ping command.* Verify that there is enough flash memory for the new Cisco IOS image using the show flash command.*
What method of wireless authentication is dependent on a RADIUS authentication server? WPA Personal WEP WPA2 Enterprise WPA2 Personal
WPA2 Enterprise*
Which wireless encryption method is the most secure? WPA WEP WPA2 with TKIP WPA2 with AES
WPA2 with AES
Launch PT Hide and Save PT Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. Which message was displayed on the web server? Work done! Congratulations! Wonderful work! You've made it!
You've made it!*
A network administrator in a branch office is configuring EIGRP authentication between the branch office router and the headquarters office router. Which security credential is needed for the authentication process? a randomly generated key with the crypto key generate rsa command a common key configured with the key-string command inside a key chain the username and password configured on the headquarters office router the hostname of the headquarters office router and a common password
a common key configured with the key-string command inside a key chain*
What are two requirements when using out-of-band configuration of a Cisco IOS network device? (Choose two.) Telnet or SSH access to the device a connection to an operational network interface on the device a direct connection to the console or AUX port a terminal emulation client HTTP access to the device
a direct connection to the console or AUX port* a terminal emulation client*
Which characteristic would most influence a network design engineer to select a multilayer switch over a Layer 2 switch? ability to build a routing table ability to aggregate multiple ports for maximum data throughput ability to provide power to directly-attached devices and the switch itself ability to have multiple forwarding paths through the switched network based on VLAN number(s)
ability to build a routing table*
What type of OSPF IPv4 route is indicated by a route table entry descriptor of O E1? an intra-area route that is advertised by the DR a summary route that is advertised by an ABR a directly connected route that is associated with an Ethernet interface an external route that is advertised by an ASBR
an external route that is advertised by an ASBR*
For troubleshooting missing EIGRP routes on a router, what three types of information can be collected using the show ip protocols command? (Choose three.) any interfaces on the router that are configured as passive any ACLs that are affecting the EIGRP routing process any interfaces that are enabled for EIGRP authentication networks that are unadvertised by the EIGRP routing protocol the local interface that is used to establish an adjacency with EIGRP neighbors the IP addresses that are configured on adjacent routers
any interfaces on the router that are configured as passive* any ACLs that are affecting the EIGRP routing process* networks that are unadvertised by the EIGRP routing protocol*
An administrator issues the router eigrp 100 command on a router. What is the number 100 used for? as the autonomous system number as the number of neighbors supported by this router as the length of time this router will wait to hear hello packets from a neighbor as the maximum bandwidth of the fastest interface on the router
as the autonomous system number*
In a large enterprise network, which two functions are performed by routers at the distribution layer? (Choose two.) connect remote networks provide Power over Ethernet to devices connect users to the network provide data traffic security provide a high-speed network backbone
connect remote networks* provide data traffic security*
Which action should be taken when planning for redundancy on a hierarchical network design? add alternate physical paths for data to traverse the network continually purchase backup equipment for the network immediately replace a non-functioning module, service or device on a network implement STP portfast between the switches on the network
continually purchase backup equipment for the network*
Which two parameters does EIGRP use by default to calculate the best path? (Choose two.) delay MTU reliability transmit and receive load bandwidth
delay bandwidth
Refer to the exhibit. Match the description to the corresponding value used by the DUAL FSM. (Not all options are used.) destination network => 192.168.11.64 feasible distance to 192.168.11.64 => 660110 —Not scored— => tid 0 new successor to network 192.168.1.0 => 192.168.3.1
destination network => 192.168.11.64 feasible distance to 192.168.11.64 => 660110 —Not scored— new successor to network 192.168.1.0 => 192.168.3.1
A network engineer is implementing security on all company routers. Which two commands must be issued to force authentication via the password 1C34dE for all OSPF-enabled interfaces in the backbone area of the company network? (Choose two.) ip ospf message-digest-key 1 md5 1C34dE area 1 authentication message-digest username OSPF password 1C34dE enable password 1C34dE area 0 authentication message-digest
ip ospf message-digest-key 1 md5 1C34dE* area 0 authentication message-digest*
Fill in the blank. Do not use abbreviations. The spanning-tree "___________________" global configuration command is used to enable Rapid PVST+.
mode rapid-pvst
When a Cisco router is configured with fast-switching, how are packets distributed over equal-cost paths? on a per-packet basis on a per-interface basis on a per-path-load basis on a per-destination basis
on a per-destination basis*
When are EIGRP update packets sent? only when necessary when learned routes age out every 5 seconds via multicast every 30 seconds via broadcast
only when necessary*
Refer to the exhibit. A network administrator is attempting to upgrade the IOS system image on a Cisco 2901 router. After the new image has been downloaded and copied to the TFTP server, what command should be issued on the router before the IOS system image is upgraded on the router? show license all ping 10.10.10.1 copy tftp: flash0: ping 10.10.10.2
ping 10.10.10.2*
Which port role is assigned to the switch port that has the lowest cost to reach the root bridge? disabled port root port designated port non-designated port
root port*
A network administrator wants to verify the default delay values for the interfaces on an EIGRP-enabled router. Which command will display these values? show ip protocols show running-config show interfaces show ip route
show interfaces*
Which technological factor determines the impact of a failure domain? the forwarding rate of the switches used on the access layer the number of layers of the hierarchical network the role of the malfunctioning device the number of users on the access layer
the role of the malfunctioning device*
What are two reasons to implement passive interfaces in the EIGRP configuration of a Cisco router? (Choose two.) to provide increased network security to shut down unused interfaces to exclude interfaces from load balancing to mitigate attacks coming from the interfaces to avoid unnecessary update traffic
to provide increased network security *** to avoid unnecessary update traffic ***
Fill in the blank. EIGRP keeps feasible successor routes in the "_______________" table.
topology
What are the two methods that are used by a wireless NIC to discover an AP? (Choose two.) sending an ARP request delivering a broadcast frame transmitting a probe request initiating a three-way handshake receiving a broadcast beacon frame
transmitting a probe request* receiving a broadcast beacon frame*
When should EIGRP automatic summarization be turned off? when a router has not discovered a neighbor within three minutes when a router has more than three active interfaces when a network contains discontiguous network addresses when a router has less than five active interfaces when a network addressing scheme uses VLSM
when a network contains discontiguous network addresses*
When will a router that is running EIGRP put a destination network in the active state? when the EIGRP domain is converged when there is outgoing traffic toward the destination network when there is an EIGRP message from the successor of the destination network when the connection to the successor of the destination network fails and there is no feasible successor available
when the connection to the successor of the destination network fails and there is no feasible successor available*
When does an OSPF router become an ABR? when the router has interfaces in different areas when the router is configured as an ABR by the network administrator when the router has the highest router ID when the router has an OSPF priority of 0
when the router has interfaces in different areas*