Climbing Wooden Poles

¡Supera tus tareas y exámenes ahora con Quizwiz!

The proper technique for using gaffs is to: a) jab the gaff into the pole for support b) support the majority of the climber's weight with the gaffs c) place the gaff next to the pole d) both (b) and (c) e) both (a) and (c)

d) both (b) and (c)

The tool used to test the shape, length, and width of a gaff is called a _____________. a) file gauge b) gaff file c) gaff gauge d) rasp gauge

c) gaff gauge

A lineworker should no place any tools or hardware on a crossarm and should not use any ______ for support. a) tools b) wood c) hardware d) conductors

c) hardware

Free climbing is only allowed when: a) time is a factor b) restoring service c) the employer determines that a fall restraint is infeasible or creates a greater hazard.

c) the employer determines that a fall restraint is infeasible or creates a greater hazard.

When climbing with a safety strap, or "hitch-hiking," ________. a) one hand should be on the safety strap, and the other hand should be on the pole b) both hands should be on the pole, with the strap attached to the D rings with the keeps facing in c) both hands should be on the belt d) Either (a) or (c) e) Either (b) or (c)

d) Either (a) or (c)

When maneuvering around a pole: a) keep your feet at different levels b) always step in the direction of the food located at the lower level. c) when maneuvering past an obstacle on the pole, always use a second safety lanyard to maintain fall protection. d) all of the above e) only (b) and (c)

d) all of the above

When the climbers are put on: a) the longest portion of the climber should be placed on the outside of the leg. b) the straps should be snug, but not too tight c) the pants leg should be pulled up, and excess material should be folded flat against the back of the leg. d) All of the above e) Only (b) and (c)

e) Only (b) and (c)

As a general rule, a climber should: a) inspect his equipment before leaving the ground. b) plan his route up the pole before leaving the ground. c) inspect the pole for hazards before leaving the ground. d) both (a) and (c) e) all of the above

e) all of the above

Which of the following is not a basic piece of climbing equipment? a) body belt b) climbers c) secondary safety strap d) fall restraint belt e) harness

e) harness

When ascending past an obstacle on the pole: a) a secondary safety strap, or belt is placed over the object. b) the fall restraint belt is removed from below and placed over the object. c) the secondary safety is removed after the fall restraint is secure d) the climber may then proceed to free climb to position. e) all of the above f) only (a), (b), and (c)

f) only (a), (b), and (c)

The proper length of a climber is determined by measuring from an inch below the lower portion of the knew joint to the __________ of the foot. a) heel b) toe c) center d) arch

d) arch

Which of the following is not a type of climbing belt illustrated in this section? a) The Maneuvering Safety Belt b) Lariat c) Jelco d) SuperSqueeze

a) The Maneuvering Safety Belt

A safety strap consists of: a) an adjustable belt with safety snaps on each end b) a cushion section, a pair of D rings, and an adjustable buckle c) a metal stirrup, gaffs, and gaff guards d) both (a) and (b) e) both (a) and (c)

a) an adjustable belt with safety snaps on each end

When performing a free climb: a) ascend or descend using the same arm and same leg as you climb. b) it doesn't matter which arm and leg you use while climbing. c) always climb using the opposite arm from the leg doing the lift, for balance.

a) ascend or descend using the same arm and same leg as you climb.

A climber should not use hardware and components for support during a climb. a) true b) false

a) true

One leg should be straight, with the knee locked, at all times during a climb. a) true b) false

a) true

The D size on a body belt refers to the distance from hip bone to hip bone measured around the back, plus one or two inches, depending on the manufacturer specifications. a) true b) false

a) true

The shape and angle of a gaff are preset by the manufacturer and should never be changed. a) true b) false

a) true

Under most climbing conditions, the fall restraint belt is not unfastened from the D rings of the body belt. a) true b) false

a) true

Always __________ verify that the secondary safety lanyard is attached to the D ring before letting go of the pole or disconnecting the fall restraint device. a) visually b) touch to c) listen to d) maneuver to

a) visually

When the climber needs to determine the proper length of the safety strap to allow him to comfortably climb and position himself on the pole. If the safety strap is of the proper length, he should be able to: a) maintain tension on the safety and still be able to grab both sides of the pole. b) can place the elbow of one arm on his stomach and, clenching a fist, brush his knuckles against the pole. c) adjust his gaffs. d) Both (a) and (b)

b) can place the elbow of one arm on his stomach and, clenching a fist, brush his knuckles against the pole.

When gaffs are being sharpened, a file is used only on the top ridge of the gaff, never on the flat underside. a) true b) false

b) false

Ideally the D rings on a body belt should be positioned just inside the prominent bones of the hip a) true b) false

b) false - should be just outside the hip bones

A lineworker utilizes a ______________ for the ground man to supply him with additional tools. a) tool bag b) hand line c) tag line d) rope blocks

b) hand line

A lineworker should plan the entire job of climbing, including climbing the ________ of the pole. a) low side b) high side c) top side d) angle side

b) high side

The waist size of a bod belt is really the measurement around the body at the _________. a) waist b) hips c) chest d) upper leg area

b) hips

Prior to climbing, all equipment should be __________ to make sure that it is in the proper condition to do the job that it is designed to do. a) checked for issue dates b) inspected thoroughly c) sharpened at the tip d) conditioned with leather cleaner

b) inspected thoroughly

To verify the waist size of a body belt, you should measure from: a) the roller on the tongue of the belt to the buckle b) the roller on the buckle to the center hole on the tongue c) the heel of one D ring to the heel of the other D ring d) the heel of one D ring to the center hoe on the tongue of the belt e) the heel of one D ring to the heel of the other D ring plus two inches

b) the roller on the buckle to the center hole on the tongue

When stepping up or down, a climber should _____________ his foot to position the faffs for the best support. a) straighten b) adjust c) angle d) pad

c) angle


Conjuntos de estudio relacionados

Real Estate Finance - Practice Exam

View Set

Chapter 5 Econ- The production Process and Costs

View Set

Principles of Insurance chapter 1 (exam 1)

View Set

minimizing human impact on environment biology terms

View Set