Fire Inspector Test Set ch 12-16

¡Supera tus tareas y exámenes ahora con Quizwiz!

In a isometric drawing, what degree are the angles the horizontal planes are drawn above the horizon?

30 degrees

Carbon Monoxide is most greater in concealed spaces vs open spaces by what?

50 percent

How much will steel expander 100 ft when it is heated to 1000 degrees?

9 1/2 inches

What is the covering over studs called ?

Sheathing

If all code violations have been corrected, an inspector should be sure to: (715)

compliment the owner/occupant for taking the appropriate actions

For most routine inspections, a ____ combined with appropriate photographs, drawings, and sketches is the only documentation needed to record the inspection. (712)

comprehensive inspection checklist

The most difficult aspect of dealing with people while conducting an inspection is: (713)

conducting violation discussions

Inspectors following the same sequence for similar types of occupancies increases the: (705)

consistency of the inspection process

The inspector should establish a ____ method for conducting inspections in order to better identify unsafe conditions or behaviors. (702)

consistent

Who is in charge of testing Dry chem extinguisher systems?

contractor

What type of door do freight elevators have?

counter balanced doors

Complaints that citizens file should be met with: (722)

courtesy and genuine interest

It is recommended that records be maintained on a building or facility: (698)

for its lifetime

What are the 3 activating devices on sprinkler heads?

fusible links, glass bulb and chemical pallet

What is used to test a wet pipe system to prevent unseating the alarm valve ?

the alarm bypass valve

When do fire pumps need to be tested?

the in plant manager should operate weekly

How long will rough cut timber last in a fire?

5 mins per in

How many minutes in a standard Fire test at 1000F rise ?

5 minutes and 1700 within a hour

Fire loads per pound per square inch?

5- slight 10- moderate 11-15- moderate severe 16-20- severe 20+ very severe

How many people should be on the board of appeals?

5-7

What is the occupant load factor for figuring a library reading room?

50 net ft2

What is the percentage of fire doors that work?

50%

What is the average GPM of horizontal shaft pumps?

500-1500 GPM

What is the GPM of a horizontal shaft pump?

500-1500 gpm

What is the GPMs for a orange hydrant?

500-999 GPM

What is the activation temperature of an orange head sprinkler?

500F to 575F classification is ultra high

What is the distance required between explosives and the unpacking area ?

50ft

What is the maximum height of a ordinary brick bearing wall?

6 stories

How many gallons is a fixed storage tank in a vessel?

60 gallons or larger

What is the NFPA standard for National electric code?

70

What is the maximum a property tent may cover?

75 %

What pressure must a tank be if the tank is 2/3 full?

75 PSI

The smallest diameter heavy timber can be is___.

8 inches

What temperature does cold drawn steel cable fail?

800 degrees

Class A ordinary combustibles put off how many BTUs?

8000

What is BTU difference between wood& paper compared to plastics and liquids?

8000 btus vs 16000 btus

Fire Barrier

A barrier which is continuous from outside wall to outside wall which continues through concealed spaces above ceilings and interstitial spaces is:

6

A beam in heavy timber is ________ inches

girder

A beam that supports other beams is a __________

apartment

A building with 3 or more living units with independent cooking and bathroom facilities is:

What type of beam has a C or a U?

A channel beam

What is the upper part of a truss called?

A chord

18

A clearance of at least _________ should be maintained under sprinklers, measured from the deflector.

60

A container is a storage receptacle with a capacity of _____ gallons or less.

Where should conversations that involve the exchange of detailed information or complete concentration take place? (691)

A controlled environment

What type of Class A fire is halon not effective on?

A deep seated class A

What is a plot plan aka site plan?

A drawing showing the location of a building on its plot of land and various details of the land

annually

A dry pipe system should have a trip test at least _______________.

18

A fire will double in intensity with each ___ degree increase in temperature.

Central Station System

A ____________________ ties several separate local local alarm systems into a central location.

yearly

Alarm test and water flow alarm testing on wet pipe sprinkler systems should be performed at least ______________.

Which foam expansion rate is used primarily to extinguish fires involving liquid fuels? Select one: a. Trace b. High c. Medium d. Low

D

Which foam expansion rate is useful as a space-filling agent? Select one: a. Trace b. Low c. Medium d. High

D

Which foam proportioner allows for automatic proportioning over a wide range of flows and pressures and does not depend on an external power source? Select one: a. Coupled water motor-pump proportioner b. Balanced pressure proportioner c. Around-the-pump proportioner d. Pressure proportioning tank system

D

Which verbal skill requires recognizing that the listener may have a different point of view? (693)

Engaging in a dual perspective

What is the highest Hazard number on NFPA placards?

4

What is the size of the office opening of a sprinkler?

1/2 inch

60

A portable tank is greater than _____ gallons and not fixed.

What type of sprinkler head hangs down ?

Pendant

What is needed to stabilize a pre-cast tilt slab wall?

The roof

What type of ID is required for bulk haz-mat storage ?

4 digit ID number

What is the GPMs for a light green hydrant?

greater then 1500 GPM

What is the GPMs on a RED hydrant?

less then 500 gpm

volts-

measures the PRESSURE of electricity

What are the 2 ways steel strength is used?

tension and compression

What color does blue stand for in placard book?

Health hazards

What is a continuous beam?

One supported by 3 or more points

stretcher

A _____________ course of brick is laid lengthwise along a wall.

Feedback

Responses that clarify and ensure that the message was received and understood

Rebar # is as follows?

#4=4/8 #5=5/8

What is the basic PSI elevation figure?

.434 lbs of pressure per 1 ft Rule of thumb- 5PSI per floor

What is the thickness of a trap door for a stage?

1 1/2"

A life fire watch is needed if the fire alarm system is out of service for what length of time?

4 hours or longer

What increments do modular drawings have?

4 ins

What is the rate of rise for a Class b ramp?

1 ft of rise for every feet of length

What are the 2 most common smoke detectors?

1- Ionization 2- Photo- electric

What are the 4 water supplies for systems?

1- Municipal 2-Gravity tank 3-Reservoir tank with pump 4- pressure tank

What are two methods of pre- stressing concrete?

1- Pre-tensioning (done at plant) 2- Pro- tensioning (done at job site)

What are the 5 basic principles of inspecting?

1- interaction with people 2- preparing for inspection 3- the inspection 4- follow up inspections and 5- maintaining the files

What is requirement for spare sprinkler heads?

1-300- 6 spares 301-1000- 12 spares 1001or more - 24

What is the function of a jock pump?

1-small pump with slightly higher pressure rating then a main fire pump 2- used to maintain pressure in the system

What skills are needed to be effective listener?

1. Attending 2. Understanding 3. Remembering 4. Evaluating 5. Responding

What complaint information should be kept by an inspector?

1. Date/time complaint received 2. Locations of perceived violation 3. Name of person reporting complaint 4. Nature of complaint or perceived violation 5. Date/time of inspection 6. Date/time of follow-up inspection 7. Resolution of comlaint

What types of written communications might an inspector use in the course of business?

1. Email 2. Interoffice memos 3. Formal business letters to owners/occupants and outside agencies 4. Reports on the inspections and complaint investigations

What does an inspector II look for when evaluating an emergency plan?

1. Emergency-reporting procedures for facility personnel 2. Duties and responsibilities of facility personnel in the event of an emergency 3. Procedures for personnel to evacuate the facility, relocate to another area, and/or shelter in place 4. Procedures for conducting emergency fire drills 5. Information about facilities fire protection systems.

What skills are needed in order to converse successfully?

1. Engage in dual perspective 2. Take responsibility for personnel feelings and thoughts 3. Show respect for the feelings and thoughts of the other person 4. Try to gain accuracy and clarity in speaking 5. Be aware of any special needs of the receiver 6. Avoid speaking or addressing a problem with anger or emotion 7. Eye contact 8. Body language 9. Facial expression 10. Gestures 11. Poise 12. Personal appearance 13. Touch 14. Proximity 15. Use of Time

List types of files and records normally maintained by an inspection organization or agency?

1. Facility inspection files 2. Inspection reports, forms, checklists, and letters 3. Violation notices 4. Plans review comments, approval and drawings 5. Investigation reports 6. Permits and certificates of occupancy 7. Complaints

Describe the common inspection procedures.

1. General inspection practices 2. Inspection concerns 3. Photographs 4. Inspection forms and checklist 5. Inspection drawings 6. Building occupancy changes 7. Results interview 8. Inspection-related letters and reports

List the enforcement duties of an inspector.

1. Inspect new and existing buildings and facilities for code compliance. 2. Verify occupancy loads 3. Investigate complaints 4. Evaluate emergency preparedness plans 5. Review construction and renovation plans

What makes a complaint complex?

1. It doesn't involve a single, straight forward issue 2. May require an interpretation on a particular code and research into additional codes

What are some of the emergency evacuation requirements for educational facilities?

1. Monthly emergency drills that occur at different times. 2. Teachers/staff can all function as monitors and assist in proper execution of the drill. 3. Teachers/staff have the responsibility of searching ares of the school as they evacuate.

What are some of the emergency evacuation requirements for health care facilities?

1. Quarterly drills, must include all staff and use all emergency plans and follow all notifications. 2. Must have a drill on every shift every quarter.

List the basic elements of a communication model.

1. Sender 2. Message 3. Medium or channel 4. Receiver 5. Interference 6. Feedback (Response) to the sender

What is the maximum amount a mezzanine can take up of a room?

1/3 of the room

What is the common scale used for floor plans?

1/4 inch equal to one foot

How many days of notice is required when their is change of address on a certificate?

10 days

How much clearance in height and width is required for a public way?

10 ft

What is the percentage of light and heat on a ordinary household lamp?

10% is light 90% heat

What is the operating PSI of a pressurized fire extinguisher?

100 psi

What distance can a rigid beam span?

100'

What are the internal pressures of extinguishers?

100-800 psi

What is the GPMs for a green hydrant?

1000- 1499 GPM

What NFPA covers Fire inspections?

1031

What is carbon monoxides ignition temperature?

1128 degrees

The access opening to fire escapes shall not be higher than the floor by how many inches?

12 inches

What is the flammability range for carbon monoxide?

12.5 % - 74%

What temperature does aluminum melt at?

1200 degrees

What is the pressure at the highest sprinkler head in the system?

15 psi, with 7psi residual

How many times stronger is steel than concrete?

15 times stronger

How much stronger is steel vs concrete?

15 times stronger

What is the pressure in a dry sprinkler system?

15-20 psi above the trip point

For a building to be classified as a dormitory how many people must be provided with sleeping accommodations?

16 or more

Class B flammables put off how many BTUs?

16,000

What temperature is a ordinary sprinkler head at?

165 degrees

NFPA 13D requires what GPMs for residential sprinklers?

18 GPM

What is the clearance required below sprinkler heads?

18" is required under the sprinkler measured from the deflector

How many inches per person for bleachers and grandstand seating?

18in

What is the minimum clearance from combustible material for cooking equipment?

18in

What is the minimum egress width for sleeping areas in healthcare facilities?

48 inches

What is the maximum travel distance on a landing to reach the stairs?

4ft

What is the length of a temporary platform that may be erect for a new assembly?

30 days

At what occupant load is a fire alarm system required for a assembly occupancy?

300 or greater

What is the required hight of a sprinkler system supplied by a water tank?

35 ft above the highest sprinkler head

How many means of access should there be to each cell block in a correctional facility? (721)

2

A 4" sprinkler riser requires the main drain be ?

2 "

How many days before using tar kettle must a permit be obtained?

2 days

What is the minimum fire resistance rating for enclosures connecting 4 or more stories?

2 hr fire barriers

What fire rating must exposed supports for above ground tanks have?

2 or more hours

In metric what does 1 ' equal?

2.54 cm or 25.4 mm

What is the proportion of a liquid to air in a pressurized tank at 75 psi?

2/3 liquid to 1/3 air

What is the minimum rating of a door into an exit access corridor?

20 mins

What is the rating for doors in a smoke proof enclosure?

20 mins

What is the maximum travel distance to an exit in a sprinkler protected education building?

200 ft

What is the minimum distance between LPG and other flammable liquid storage tanks?

20ft

How many feet may a sprinkler cover in a low hazard?

225 sq ft

If sprinklers are omitted from a closet, it may not be over what size?

24 sq ft

Rack storage require sprinklers at which height within the racks?

25 ft

What is the practical limit distance for simple wood beam floor?

25 ft

What size basement requires sprinkler system protection?

2500 sq ft or more

How many days does concrete take to set to its designed strength?

28 days

Orthographic projections are what?

3 dimensional

What is the minimum distance between above ground flammable or combustible storage tanks ?

3 ft

For a building to be classified as a apartment how many units with independent kitchens must they have?

3 or more

A fire alarm must be in a apartment building that is?

3 or more stories or more then 11 units

How tall is a typical Platform-frame construction building?

3 stories

What is the height limit for garden apartments?

3 stories

When doe a apartment need a fire alarm system?

3 stories or more and more then 11 units

The system used when water alone may not be an effective fire extinguishing agent is a: Select one: a. foam system. b. dry powder system. c. dry-chemical system. d. carbon dioxide (CO2) system.

A

The type of fire detection and alarm system required depends upon the: Select one: a. type of occupancy of the building. b. budget of the owner/resident. c. location of nearest fire department. d. age of the building.

A

Automatic alarm-initiating devices are more commonly known as: Select one: a. detectors. b. alarms. c. activators. d. initiators.

A

Complaints that involve a serious life safety threat require: Select one: a. immediate action. b. routine investigation. c. immediate research. d. effective execution of an emergency plan.

A

Conversations that involve the exchange of detailed information or complete concentration should take place in: Select one: a. a controlled environment. b. front of witnesses. c. an uncontrolled environment. d. a public meeting.

A

How are portable fire extinguishers classified? Select one: a. Type of fire they will extinguish b. Type of occupancy in which they are located c. Type of agent used in the system d. Amount of time it takes to expel the agent

A

How are portable fire extinguishers rated Select one: a. Intended use and extinguishing capability b. /Type of occupancy and intended use c. Intended use and type of agent used d. Type of agent used and location in an occupancy

A

How are special-agent fire extinguishing systems classified? Select one: a. By the type of fire they will extinguish b. By the type of agent used in the system c. By the type of occupancy d. By the amount of time it takes to expel the agent

A

How can an inspector overcome prejudice when listening? Select one: a. Focus on the message and not the sender. b. Identify the essential elements of the message. c. Take control of the environment and remove as many outside distractions as possible. d. Focus on the speaker and the message rather than personal concerns or thoughts.

A

How many types of specialty signals are most fire detection and alarm systems equipped with? a. 3 b. 1 c. 2 d. 4

A

If an alarm signaling system uses backup electrical generators, how long should a generator run under load for a monthly test? Select one: a. 30 minutes b. 15 minutes c. 20 minutes d. 60 minutes

A

Inspectors following the same sequence for similar types of occupancies increases the: Select one: a. consistency of the inspection process. b. number of inspections that can be conducted. c. efficiency of the paperwork. d. preparedness of owner/occupants.

A

Manual pull stations are usually _____ in color with white lettering that specifies what they are and how they are to be used. Select one: a. red b. blue c. green d. black

A

Remote station and proprietary systems should be tested according to requirements established by: Select one: a. authority having jurisdiction (AHJ). b. manufacturer instructions. c. industry standards. d. fire codes.

A

The amount of time it takes to conduct an inspection: Select one: a. varies for each facility and occupancy. b. is set in model codes. c. is determined by the owner/occupant. d. varies depending upon weather conditions.

A

The best way to improve good listening skills is to: Select one: a. practice. b. work with a coach. c. take a college class. d. take a skills class.

A

The emphasis of emergency evacuation drills in educational facilities is placed on: Select one: a. orderly evacuation. b. speed. c. frequency. d. number of staff involved.

A

The inspector should establish a _____ method for conducting inspections in order to better identify unsafe conditions or behaviors. a. consistent b. secret c. varied d. random

A

The most common types of alarm-signaling systems used for signaling a fire alarm in a structure are: Select one: a. audible notification appliances. b. textual notification appliances. c. visual notification appliances. d. tactile notification appliances.

A

The stage of foam formation that mixes water with foam liquid concentrate is: Select one: a. proportioning. b. aeration. c. blending. d. separating.

A

To determine whether an administrative warrant to enter a location is needed, an inspector considers the type of occupancy, location within the occupancy, and: Select one: a. severity of the nature of the complaint. b. the time of day. c. whether children are present. d. who owns the occupancy.

A

Verifying occupant loads and investigating complaints are examples of which Inspector I job duty? Select one: a. Enforcement b. Education c. Reviews d. Communication

A

What does an inspector focus on during a follow-up inspection? Select one: a. Problem areas from the first inspection b. Owner/occupants c. Everything d. Manufacturer requirements

A

What general category of fire extinguishing agents effectively leaves no residue? Select one: a. Clean agent systems b. Dry-chemical systems c. Carbon dioxide systems d. Dry powder systems

A

What is critical to total flooding applications of carbon dioxide (CO2) systems in order for them to be effective? Select one: a. Room integrity b. Predischarge alarms c. Cost of maintenance d. Proper training in use

A

What is required for a special-agent extinguishing system to be considered successful? Select one: a. It must completely extinguish the fire b. It controls or contains a fire until the fire department arrives c. Ease of use by occupant/owners d. The cost of maintenance

A

What is the key to successfully handling any emergency, regardless of the type of occupancy? a. Effective execution of an emergency plan b. A convenient means of egress c. An effective emergency plan d. Effective training of owner/occupants

A

What is the periodic testing of fire detection and alarm signaling systems called? Select one: a. A service test b. An acceptance test c. Signal testing d. Readiness testing

A

What percentage of finished foam is water? Select one: a. 94% to 99½% b. 100% c. 1% to 5% d. 45½% to 50%

A

What should an inspector be prepared to issue regarding an inspection site for extremely hazardous conditions? Select one: a. Cease-and-desist order b. Report c. Warrant d. Permit

A

What should an inspector do when conditions that may trigger an unwanted alarm or environmental conditions that may negatively affect a system are recognized? Select one: a. Recommend corrective action b. Issue citations c. Collect fines d. Contact law enforcement

A

Which dry-chemical system component releases agent into the piping system? Select one: a. Actuating mechanism b. Nozzles c. Storage container d. Hydrants

A

Which fire extinguisher agent extinguishes primarily through a smothering action? Select one: a. Carbon dioxide (CO2) b. Water c. Foam d. Dry chemical

A

Which of the following actions is an example of how an inspector can control external interference during an inspection? Select one: a. Close a door or window b. Turn on a radio c. Use nonverbal clues d. Lower the temperature

A

Which of the following helps prevent firefighters and emergency responders from dealing with unknown and potentially dangerous structural conditions? Select one: a. Building permits b. Limiting response to known conditions c. Interviewing victims at the scene d. Interviewing bystanders at the scene

A

Which of the following is the BEST reason information about construction projects is useful? Select one: a. Preincident planning b. Release of community data c. Collection of fines d. Determining annual response fees

A

Which of the following is the main reason local governments require construction permits and plans review? a. Community safety b. Collection of fees c. Increase control within a community d. Show a need for specific positions

A

Which of the following tasks regarding dry-chemical systems is an Inspector I MOST likely to be required to perform? Select one: a. Inspect new installations b. Evaluate application methods c. Evaluate inspection and testing requirements d. Conduct acceptance tests

A

Which rate-of-rise heat detector is designed for use in areas subject to regular, but slow, temperature changes? Select one: a. Rate-compensation heat detector b. Electronic spot-type heat detector c. Pneumatic rate-of-rise spot heat detector d. Pneumatic rate-of-rise line heat detector

A

Which supervising station does not provide inspection, testing, or maintenance services? Select one: a. Remote b. Central c. Local d. Proprietary

A

Which task in Monroe's Motivated Sequence Pattern includes describing the solution for the problem and how it will benefit the listener? Select one: a. Visualization b. Action c. Satisfaction d. Need

A

Which task in Monroe's Motivated Sequence Pattern involves describing the problem and demonstrating a need for a change? Select one: a. Need b. Visualization c. Action d. Satisfaction

A

Which type of dry powder agent is sodium chloride (salt) based? Select one: a. MET-L-X® b. Halon c. LITH-X® d. NA-X®

A

Which type of dry-chemical fixed application method introduces a concentration of agent into a closed area? Select one: a. Total flooding b. Local application c. Handheld hoseline d. Fire extinguishers

A

Who is responsible for training employees in emergency evacuation of hotels and motels? Select one: a. Owner or administrator b. Fire department c. Fire marshal d. Training contractors

A

Who is responsible for verifying that construction activities conform to the plans approved by the plans examiner and issued as part of the permit documents? Select one: a. Inspector b. Insurance representative c. City manager d. Fire marshal

A

Who should the inspector invite to accompany the inspector during the inspection? Select one: a. The building owner/occupant b. A firefighter c. A building custodial employee d. The nearest law enforcement officer

A

Raceway

A ____________ is an open channel used to run pipes and wiring.

What is a beam?

A horizontal structure member used between posts, columns, or walls.

According to NFPA 1, what is a highly volatile liquid?

A liquid with a boiling point of less than 68 F

What is a schedule on a plan?

A list of details or sizes for building components such as doors, windows or beams and done by the architect

What is a concentrated load?

A load located at one point

What is a chase?

A passageway, usually vertical, cut into a masonry wall for a pipe or conduit

remote station

A premise in which the alarm system is monitored directly by the fire department is called a ______________

rate of rise

A rate compensated detector is the same as a ________________ detectoR

central station

A separate and private contractor monitors several locations and systems is called a _____________ system.

How is air removed rapidly from a dry pipe system?

Accelerator- rapidly dumps air in the water side of the system Exhauster- rapidly dumps air into the outside atmosphere

GARDEN APARTMENTS

According to Brannigan, what describes row houses, town houses, or low-rise, multi-family units?

175-225

A sprinkler head with the frame painted white is rated at

Ashlar

A stone used in construction which is cut or sawn into rectangular shapes is called ____________ masonry.

60

A storage tank is a vessel greater than _____ gallons and fixed

proprietary

A system which protects buildings belonging to the same owner is a _________________ system.

What is another name of the solution composed of potassium carbonate?

A wet chem extinguishing agent

Who has the ultimate authority to make changes to fire codes?

AHJ

What are the two materials that flame spread rating is based on?

Abestco cement board and red oak wood

15-20

Air pressure on dry pipe sprinkler systems must be maintained at ____ to ____ PSI above the trip point.

Public Relations

Activities focused on promoting the organization by creating a public perception that is positive and that creates public support for the organization

Which landings have standpipe connections in scissor stairs ?

Alternating floors

local

An alarm system that detects and reports a fire only on the immediate premises is called a _____________.

monthly

An alarm test on a dry pipe system should be performed at least ____________.

135 - 175

An unpainted sprinkler head is rated at _________________.

What is a live load?

Any load to a building other then a dead load

25

Any standpipe out of service for a period of time must be charged with air at ______ PSI.

What are 2 of the reasons electrical fires start?

Arcs or over heating

Where is the annunciator panel located in a building?

Areas approved by AHJ

What should a inspector do before performing any inspections ?

Ask for permission to inspect the building

What size are hydrant supply mains for residential areas?

At least 8 inches with 6 inches in diameter

Where in a woodworking shop is a fire most likely to occur?

At the dust hogger

Which listening skill focuses on the speaker and ignores other distractions? (692)

Attending

A large portion of inspector communication involves: Select one: a. arguing. b. listening. c. writing. d. mediating.

B

A(An) _____ is a warning of a fire emergency or dangerous condition that demands immediate attention. Select one: a. supervisory signal b. alarm signal c. alert signal d. trouble signal

B

An inspector should process and act upon each complaint: Select one: a. as quickly as possible. b. in a consistent manner. c. in the order in which they are received. d. like a serious life safety threat.

B

An inspector should visit the site often to: a. determine whether OSHA violations are occurring. b. verify each code requirement is being met based on the approved plan. c. collect any necessary fees for services. d. spot approve any changes in the original plan.

B

At a construction site, an inspector must comply with _____ regulations or locally adopted requirements for the use of personal protective clothing and equipment. Select one: a. Environmental Protection Agency (EPA) b. Occupational Safety and Health Administration (OSHA) c. building department d. insurance

B

Conducting plans review enables plans examiners to: Select one: a. determine appropriate fees. b. discover any errors or omissions in a building plan. c. determine insurance rates. d. discover demographic information about occupants.

B

During a construction site visit, if an inspector finds violations, the: a. local zoning department official should be notified. b. general contractor should be notified. c. building department should be notified. d. financial backers should be notified.

B

During a monthly test for alarm signaling systems using backup electrical generators, how long should a generator run under load? Select one: a. 60 minutes b. 30 minutes c. 20 minutes d. 15 minutes

B

Follow-up inspections are made to verify that corrections noted in the inspection report have been: Select one: a. started. b. completed. c. issued permits. d. noted.

B

Ideally, inspection records should be maintained for _____ properties or facilities within a jurisdiction. Select one: a. occupied b. all c. hazardous d. valuable

B

If all code violations have been corrected, an inspector should be sure to: Select one: a. post a notice to the public that the violations have been corrected. b. compliment the owner/occupant for taking the appropriate actions. c. schedule a new inspection for the following year. d. provide refunds for any fees issued.

B

On construction drawings, abbreviations and symbols are widely used and plans reviewers: Select one: a. do not need to be familiar with abbreviations and symbols as these are not standard. b. should be familiar with some of the more commonly used abbreviations and symbols. c. should be familiar with all abbreviations and symbols used. d. often need the assistance of a design professional to decipher the abbreviations and symbols.

B

On which principle of physics does a rate-of-rise heat detector operate? Select one: a. Heated materials have thermoelectric properties b. Fires rapidly increase the temperature of a given area c. Heat causes the expansion of various materials d. Heat causes melting of certain materials

B

Periodic testing of fire detection and alarm signaling systems is referred to as: a. an acceptance test. b. a service test. c. readiness testing. d. signal testing.

B

Portable fire extinguishers are classified by the: Select one: a. type of agent used in the system. b. type of fire they will extinguish. c. type of occupancy in which they are located. d. amount of time it takes to expel the agent.

B

The primary reason local governments require construction permits and plans review is: Select one: a. to document the need for specific job positions. b. regard for community safety. c. to increase revenue for the agency. d. to lower jurisdiction insurance rates.

B

The simplest type of protected premises alarm system is a(an): Select one: a. zoned conventional alarm system. b. conventional alarm system. c. addressable alarm system. d. supervising station system.

B

The special-agent fire extinguishing system that is extremely cold and can freeze exposed skin is the: Select one: a. dry powder system. b. carbon dioxide (CO2) system. c. clean agent system. d. dry-chemical system.

B

What determines retention time for records? Select one: a. State and federal law b. Jurisdictional policies and procedures c. Consensus standards d. Model codes

B

What is one of the most important duties an inspector has when it comes to interacting with various officials and the general public about the basis and importance of the fire and life safety codes? a. Investigations b. Communication c. Inspections d. Enforcement

B

What is the first step in scheduling an inspection? Select one: a. Contact legal counsel for warrants. b. Contact the facility owner/occupant to determine a mutually agreeable date and time. c. Contact law enforcement to check availability for an escort. d. Contact neighboring structures to alert them to the impending inspection

B

What kind of communication is body language? Select one: a. Professional b. Nonverbal c. Secondary d. Verbal

B

What listening skill involves critically analyzing the message to determine how factual it is? Select one: a. Understanding b. Evaluating c. Responding d. Attending

B

What should an inspector do to assist an owner/occupant in finding a solution to remedy a violation? Select one: a. Nothing b. Refer to the appropriate professional c. Design a solution d. Provide a copy of the code

B

What type of special-agent fire extinguishing system is used when rapid fire extinguishment is required and where reignition is unlikely? Select one: a. Wet-chemical systems b. Dry-chemical systems c. Dry power systems d. Clean agent systems

B

When discussing violations, nothing erodes an owner/occupant's confidence in an inspector more than: Select one: a. being rude. b. finding a mistake. c. looking sloppy. d. arriving late.

B

When is photographic documentation particularly helpful regarding an inspection? Select one: a. During routine inspections b. When documenting violations that may result in a citation or legal action c. During business hours d. When the inspector is in a hurry

B

When occupants remain in a building during construction, an inspector must verify: a. a building monitor is posted on every floor. b. all means of egress are clear. c. occupants can exit the building in under five minutes. d. occupants can exit the building in under seven minutes.

B

When planning for an inspection, the first consideration for an inspector is to: Select one: a. make friends with the owner/occupants. b. prepare to conduct the inspection safely. c. memorize codes and standards. d. find as many violations as possible.

B

When rapid fire extinguishment is required and reignition is unlikely: Select one: a. wet-chemical systems are used. b. dry-chemical systems are used. c. clean agent systems are used. d. dry powder systems are used.

B

When should automatic alarm-initiating devices be checked? Select one: a. After installation, after a fire, and every 3 years b. After installation, after a fire, and at scheduled times based on guidelines c. Annually d. After installation and every 5 years

B

Which basic element of a communication model contains a meaning, idea or concept that a speaker is attempting to communicate? Select one: a. Sender b. Message c. Medium d. Interference

B

Which component's power supply usually comes from the building's main power connection to the local utility provider? Select one: a. Extra alarm functions b. Primary power supply c. Initiating device d. Secondary power supply

B

Which fire alarm component serves as the brain of alarm systems Select one: a. Secondary power supply (SPS) b. Fire alarm control unit (FACU) c. Initiating device d. Notification appliance

B

Which foam proportioner is the most common type of built-in proportioner installed in mobile fire apparatus? Select one: a. Pressure proportioning tank system b. Around-the-pump proportioner c. Balanced pressure proportioner d. Coupled water motor-pump proportioner

B

Which listening skill consists of decoding a message and assigning meaning to it? Select one: a. Attending b. Understanding c. Remembering d. Evaluating

B

Which nonverbal communication skills require attention to cultural differences? Select one: a. Gestures and facial expressions b. Eye contact and proximity c. Eye contact and facial expressions d. Gestures and personal appearance

B

Which of the elements of a memo provides details regarding a topic? Select one: a. Advice b. Information c. Direction d. Introduction

B

Which of the following is an area that fire department plans examiners are MOST likely trained in? a. Design and installation of electrical systems b. Fire protection systems, including sprinklers, standpipes, and fire detection and alarm devices c. Zoning requirements of locally adopted codes d. Design and installation of plumbing systems

B

Which of the following makes inspector site visits more efficient and effective? Select one: a. Coordinating inspections when contractors are unaware of dates b. Coordinating inspections with completion dates c. Coordinating inspections with employee work times d. Coordinating inspections with other duties in the area

B

Which of the following provides the BEST example of an occupancy with a complex emergency evacuation drill? Select one: a. Grocery store b. Health care facility c. Single-family home d. Garage

B

Which special-agent fire extinguishing system is extremely cold and can freeze exposed skin? Select one: a. Clean agent systems b. Carbon dioxide systems c. Dry-chemical systems d. Dry powder systems

B

Which special-agent fire extinguishing system is most effective on fires in commercial cooking equipment that produces grease-laden vapors? Select one: a. Clean agent systems b. Wet-chemical systems c. Dry powder systems d. Dry-chemical systems

B

Which statement about inspector site visits during construction is MOST accurate? Select one: a. Unless there is a problem, an inspector does not need to visit the site. b. An inspector should visit the site often. c. Site visits are determined by the owner/occupant. d. An inspector should visit the site at the start and end of the project.

B

Which system is used when water alone may not be an effective fire extinguishing agent? Select one: a. Dry powder system b. Foam system c. Carbon dioxide system d. Dry-chemical system

B

Which type of automatic initiating devices are relatively inexpensive and least prone to nuisance alarms? Select one: a. Flame detection devices b. Heat detection devices c. Combination detection devices d. Smoke detection devices

B

Which type of fire detection and alarm system specialty signal indicates an off-normal condition of the complete fire protection system? Select one: a. Alarm signal b. Supervisory signal c. Trouble signal d. Alert signal

B

Which type of fixed-temperature heat detector uses two types of metal with different heat-expansion ratios? Select one: a. Fusible link b. Bimetallic c. Frangible bulb d. Continuous-line

B

Which type of foam fire extinguishing system is wheel mounted and may have a water supply connection capability? Select one: a. Semifixed b. Mobile c. Fixed d. Portable

B

Which type of foam system method extinguishes a fire by intervening between the fuel and the fire? Select one: a. Smothering b. Separating c. Suppressing d. Cooling

B

Which type of smoke detector contains a sensing chamber consisting of two electrically charged plates and a radioactive source? Select one: a. Photoelectric smoke detectors b. Ionization smoke detectors c. Duct smoke detectors d. Pneumatic rate-of-rise spot heat detectors

B

Which type of special-agent fire extinguishing system is used for combustible metal fires? Select one: a. Foam systems b. Dry-powder systems c. Dry-chemical systems d. Carbon dioxide (CO2) systems

B

Who should the inspector notify when violations are found during a site visit? Select one: a. Building department official b. General contractor c. Insurance representative d. Fire marshal

B

Explain Monroe's Motivated Sequence

Basic outline for persuading people using attention, need, satisfaction, visualization, and action.

The Stretcher course?

Brick laid lengthwise

What is the stretcher course?

Brick laid lengthwise

What is a wythe?

Bricks laid so the long side is visible

What is the symbol for class C fires?

Blue circle

How can site plan drawings assist an inspector conducting an inspection? (706)

Note location of violations

hydrogen cyanide

Burning wool emits _______________.

How are fire dampers activated?

By fusible links

What does an inspector need to do to prepare for an inspection?

By reviewing the structure or facility inspection records as well as the applicable fire codes and standards

A permanent record of all detector tests must be maintained for at least: Select one: a. 3 years b. 10 years c. 5 years d. 25 years

C

All components of emergency voice/alarm systems should be tested at least: Select one: a. semiannually. b. monthly. c. annually. d. weekly.

C

An inspector needs to be proficient in various types of: Select one: a. languages. b. natural sciences. c. written communication. d. mathematics.

C

Complaints that citizens file should be met with: Select one: a. skepticism. b. doubt. c. courtesy and genuine interest. d. grace and caution.

C

Emergency evacuation drills in health care facilities are conducted: Select one: a. weekly on each shift. b. monthly on each shift. c. quarterly on each shift. d. annually on each shift.

C

How can site plan drawings assist an inspector conducting an inspection? Select one: a. Label occupancy loads b. Identify rooms c. Note location of violations d. Locate people

C

How many means of access should there be to each cell block in a correctional facility? Select one: a. 3 b. 1 c. 2 d. 4

C

Portable fire extinguishers are rated by: Select one: a. type of occupancy and intended use. b. type of agent used and location in an occupancy. c. intended use and extinguishing capability. d. intended use and type of agent used.

C

Primarily, administrative duties for inspectors include: Select one: a. custodial duties. b. forensic investigation. c. preparing written communications. d. answering the phone.

C

Special-agent fire extinguishing systems are classified by the: a. amount of time it takes to expel the agent. b. type of agent used in the system. c. type of fire they will extinguish. d. type of occupancy.

C

The four elements necessary to produce high-quality fire fighting foam include foam concentrate, water, mechanical agitation, and: Select one: a. halon. b. carbon dioxide (CO(2). c. air. d. gas.

C

The inspector or plans examiner who reviews the plans: Select one: a. must have another inspector or plans examiner also review them. b. must have an independent third party review and verify any comments. c. may also be responsible for field verification. d. cannot be responsible for field verification.

C

The key to successfully handling any emergency, regardless of the type of occupancy, is: Select one: a. a convenient means of egress. b. an effective emergency plan. c. effective execution of an emergency plan. d. effective training of owner/occupants.

C

The preferred type of automatic alarm device in residences and health and institutional care facilities is a: Select one: a. rate-compensation heat detector. b. pneumatic rate-of-rise line heat detector c. smoke detector. d. pneumatic rate-of-rise spot heat detector

C

The special-agent fire extinguishing system most effective on fires in commercial cooking equipment that produces grease-laden vapors is a: Select one: a. dry powder system. b. dry-chemical system. c. wet-chemical system. d. clean agent system.

C

What basic element of a communication model gives the path that a message takes? Select one: a. Feedback b. Sender c. Medium d. Interference

C

What determines whether an inspection is effective or not? Select one: a. Inspector memorization of codes and standards b. The amount of experience an inspector possesses c. Time spent reviewing the structure or facility inspection records d. Inspector's relationship with owner/occupants

C

What do heat detectors require in order to be effective? Select one: a. Professional installation b. Continuous testing c. Proper placement d. 24-hour monitoring

C

What listening skill involves the feedback portion of the communication process? Select one: a. Attending b. Evaluating c. Responding d. Understanding

C

What method should an inspector establish in order to better identify unsafe conditions or behaviors? Select one: a. Secret b. Varied c. Consistent d. Random

C

What must be verified to ensure that fire and life safety requirements are met during construction? Select one: a. Fire watch personnel b. Rehabilitation or rest area c. Site access d. Adequate number of employees

C

What should an inspector do if none of the violations have been corrected and no effort has been made by the owner/occupant to correct the violations? Select one: a. Schedule a new inspection for the following year b. Note the lack of correction in the file c. Issue a final notice with a date for another inspection d. Force the owner/occupant to take the appropriate actions

C

What should inspectors display or have available for immediate review when arriving for an inspection? Select one: a. Warrant b. Model code c. Identification d. Judge's order

C

What type of special-agent fire extinguishing system is used for combustible metal fires? Select one: a. Foam agent systems b. Carbon dioxide systems c. Dry powder systems d. Dry-chemical systems

C

What will a review of the inspection records file reveal about an upcoming inspection? Select one: a. Construction information b. What equipment to take c. Types of hazards that may be present d. Number of occupants

C

When communicating, the greatest distraction is the listener's: Select one: a. cell phone. b. prejudice. c. internal voice. d. information overload.

C

Where should conversations that involve the exchange of detailed information or complete concentration take place? Select one: a. A public place b. In front of law enforcement c. A controlled environment d. An uncontrolled environment

C

Which component sends a signal to the FACU using either hard-wire systems or a signal conveyed by radio wave over a special frequency? Select one: a. Primary power supply b. Notification appliance c. Initiating device d. Secondary power supply

C

Which element of the communication model completes the communication process? Select one: a. Sender b. Interference c. Feedback d. Medium

C

Which fire extinguisher agent is subject to freezing if not kept in a heated area or an antifreeze agent added? Select one: a. Dry chemical b. Carbon dioxide (CO2) c. Water d. Foam

C

Which is the BEST option for preventing an owner/occupant from attempting to omit a requirement? Select one: a. An independent monitor b. Insurance rate increases c. A team approach d. Significant fines or fees

C

Which listening skill focuses on the speaker and ignores other distractions? Select one: a. Understanding b. Remembering c. Attending d. Evaluating

C

Which of the following BEST describes a zoned conventional alarm system? Select one: a. They are only practical for small occupancies with a limited number of rooms b. Usually activated by manual means, such as a pull station c. An annunciator panel, FACU, or printout visibly indicates the location of an operating alarm-initiating device d. This system is found in occupancies that use the alarm signals for other purposes

C

Which of the following establishes the basis for all future inspections of a building? Select one: a. Final insurance report on rates and exemptions for the building b. Final building review issuing occupancy guidelines and permits c. Accurate and complete record keeping during plans review and field verification visits d. Owner documentation of construction and maintenance

C

Which of the following is the BEST example of a compliance issue that an inspector may check in an assembly occupancy after hours? Select one: a. An appropriate number of points of egress b. Investigation of non-urgent complaints c. Presence of locked, blocked, or obstructed exits d. Construction permits

C

Which of the following statements about public emergency alarm reporting systems is MOST accurate? Select one: a. Initiating devices cannot be activated when the power supply to the municipal system is interrupted. b. These systems cannot be connected via telephone lines. c. Power interruption may result in the alarm only sounding locally. d. They are connected directly to the fire department via the Internet.

C

Which of the following statements is MOST accurate regarding computer records? Select one: a. They greatly decrease security of records management and retention. b. They greatly reduce the ability to share information efficiently. c. They greatly increase efficiency and accuracy in records management and retention. d. They greatly increase security of records management and retention.

C

Which of the following usually establishes the exact manner in which plans must be submitted for review? Select one: a. Building owner/occupant b. National building standards c. Authority having jurisdiction d. Design professional

C

Which supervising station is recognized as the most reliable? Select one: a. Proprietary b. Local c. Central d. Remote

C

Which type of emergency communications system is MOST helpful to fire suppression personnel operating in a building? Select one: a. Voice notification systems b. Cellular phone systems c. Two-way communication systems d. Mass notification systems

C

Which type of fire detection systems are among the oldest still in service? a. Smoke detection devices b. Flame detection devices c. Heat detection devices d. Combination detection devices

C

Which type of fire extinguisher stores expellant gas and extinguishing agent in a single chamber? Select one: a. Loaded-stream extinguisher b. Cartridge-operated extinguisher c. Stored-pressure extinguisher d. Pump-operated extinguisher

C

Which type of manual pull station may be confusing to certain occupant/operators? Select one: a. Those with glass windows and mallets b. Single-action c. Double-action d. Those with protective covers

C

Which type of smoke detector works on all types of fires and usually responds more quickly to smoldering fires than ionization smoke detection? Select one: a. Pneumatic rate-of-rise spot heat detectors b. Duct smoke detectors c. Photoelectric smoke detectors d. Video-based detectors

C

What should an inspector be prepared to issue regarding an inspection site for extremely hazardous conditions? (704)

Cease-and-desist order

What type of valve limits flow in one direction?

Check valves

What are the components of a truss?

Chords- top and bottom members struts- the compressive connecting members ties- tensile connecting members and connections are called panel points

Means of Egress

Continuous and unobstructed way of travel from any point in a building or structure to a public way consisting of 3 separate and distinct parts

Where are noted placed for a welding symbol?

Notes are placed within the tail

What type of fires does CO2 and dry chem used on?

Class B and C

What type of air filter releases little or no gas when subjected to fire?

Class I

Which of the following actions is an example of how an inspector can control external interference during an inspection? (691)

Close a door or window

National Fire Incident Reporting System (NFIRS)

Collects data on the many Underlying factors of a fire

NFPA 30

Combustible and flammable liquid codes

What is one of the most important duties an inspector has when it comes to interacting with various officials and the general public about the basis and importance of the fire and life safety codes? (689)

Communication

POOR SHEER RESISTANCE

Concrete resists compression and has:

PRE STRESSED

Concrete that internal stresses being applied to resist external forces or loading is called ___________ concrete.

What method should an inspector establish in order to better identify unsafe conditions or behaviors? (702)

Consistent

What is the first step in scheduling an inspection? (702)

Contact the facility owner/occupant to determine a mutually agreeable date and time

What causes heat and smoke to spread upward then outward within a building?

Convection

What is a Byrd's mouth cut?

Cut in a rafter to make it fit flush on the top plate

Clearance between the bottom of the extinguisher and the floor should never be less than: Select one: a. 3 inches (76 mm). b. 5 inches (127 mm). c. 6 inches (152 mm). d. 4 inches (100 mm).

D

Emergency evacuation drills should be conducted in: Select one: a. high-rise structures. b. malls and shopping centers. c. schools and churches. d. all types of occupancies.

D

For most routine inspections, a _____ combined with appropriate photographs, drawings, and sketches is the only documentation needed to record the inspection. Select one: a. formal report b. brief inspection summary c. comprehensive list of local codes d. comprehensive inspection checklist

D

If the owner or contractor fail to follow the requirements of the building or fire code, records may be required for use in: Select one: a. employee or subcontractor pay disputes. b. insurance rate increases. c. rezoning claims. d. any legal action.

D

Inspectors should check the FACU to verify: Select one: a. component age. b. components are not blocked or obstructed in any way. c. changes in occupancy. d. all parts are operating properly.

D

It is recommended that records be maintained on a building or facility: Select one: a. until it changes owners. b. for 10 years. c. for 5 years. d. for its lifetime.

D

Most of the time, who has to test fire alarm systems on their own and document results? Select one: a. Building contractors b. Third-party experts c. Fire inspectors d. Occupants

D

Multistory facilities should have at least _____ pull station(s) on each floor. Select one: a. 3 b. 2 c. 4 d. 1

D

The AHJ establishes a plans review and permitting process to verify structures that are new, remodeled, or have a change in occupancy classification meet the requirements of: Select one: a. state adopted building and fire codes. b. local homeowner or business associations. c. national standards. d. locally adopted building and fire codes.

D

The fire alarm component that serves as the brain of an alarm system is called the: Select one: a. notification appliance. b. initiating device. c. secondary power supply (SPS). d. fire alarm control unit (FACU).

D

The general category of fire extinguishing agents that effectively leaves no residue is a: Select one: a. dry-chemical system. b. carbon dioxide (CO2) system. c. foam system. d. clean agent system.

D

Which fire extinguisher agent is especially suitable for controlling fires outdoors? Select one: a. Water b. Carbon dioxide (CO2) c. Foam d. Dry chemical

D

The most difficult aspect of dealing with people while conducting an inspection is: a. making appointments. b. rescheduling inspections. c. meeting people for the first time. d. conducting violation discussions.

D

The one style of heat detection device that can be used to detect conditions over a wide area is a: Select one: a. bimetallic detector. b. frangible bulb detector. c. fusible link detector. d. continuous-line detector.

D

The success of an inspection visit depends upon how familiar an inspector is with: a. consensus standards. b. model codes. c. the people who own the property. d. the site being inspected.

D

The type of emergency communications system used to provide emergency communication to a large number of people on a wide-scale basis is a: Select one: a. public address system. b. two-way communication system. c. cellular phone system. d. mass notification system.

D

The value of a fire extinguisher lies in: Select one: a. its ease of use. b. where it is located. c. how big it is. d. the speed with which it can be used.

D

To ensure that fire and life safety requirements are met during construction, an inspector must verify: a. trained fire protection personnel are on site. b. mutual aid agreements. c. manager/employee ratio. d. a reliable water supply.

D

Usually, all e-mail messages that are written by public officials during the performance of their duties are: Select one: a. destroyed quickly. b. personal property. c. private. d. official documents.

D

Wet-chemical fire extinguishing agents are delivered to the hazard area in the form of a: Select one: a. stream. b. drip. c. foam. d. spray.

D

What are automatic alarm-initiating devices more commonly known as? Select one: a. Activators b. Initiators c. Alarms d. Detectors

D

What can be used to test restorable heat detectors during a test? Select one: a. Restorable heat detectors cannot be tested b. Matches c. Setting a test fire d. Hair dryers and electric heat guns

D

What inspector practice goes a long way in providing education and building a positive image of fire prevention activities? Select one: a. Writing skills b. Punctuality c. Issuing citations d. Professional attitude

D

What is the best way to improve good listening skills? Select one: a. Training b. Coaching c. Formal education d. Practice

D

What is the biggest disadvantage to dry-chemical systems? Select one: a. Difficult to find b. Complicated to use c. Cost d. Require extensive cleanup

D

What is the greatest concern for extinguisher reliability? Select one: a. Distribution of units b. Placement c. Type of agent used in units d. Temperature of the environment

D

What is the most difficult aspect of dealing with people while conducting an inspection? Select one: a. Rescheduling inspections b. Meeting people c. Making appointments d. Violation discussions

D

What must an inspector be prepared to deal with by business owner/occupants when they act on complaints? Select one: a. Protests b. Legal action c. Physical harm d. Negative attitudes

D

What serve as official records of an inspection and form the basis for legal action when required? Select one: a. Photos and drawings b. Copies of codes c. Emails and memos d. Letters and reports

D

What should an inspector do when an owner/occupant denies access to the property to be inspected? Select one: a. Document the action and make note to return in 30 days. b. Contact a judge for a warrant. c. Contact law enforcement to force access. d. Document the action and follow departmental protocols for securing permission to obtain legal access.

D

What should an inspector look for when inspecting manual pull stations and audible or visual warning devices? Select one: a. Component age b. Changes in occupancy c. Devices are free of dust, dirt, and paint d. Components are not blocked or obstructed in any way

D

When communicating, what prevents the receiver from fully receiving a message? Select one: a. Sender b. Medium c. Message d. Interference

D

When inspecting areas that involve noisy operations, it may be necessary to: Select one: a. reschedule the inspection. b. use nonverbal cues. c. wear hearing protection. d. take notes.

D

When occupants remain in a building during construction, and a fire detection or alarm system will be nonfunctional for any length of time: Select one: a. occupants should be notified and given the choice to leave. b. additional firefighting personnel should be on duty. c. notices must be posted at entrances. d. a fire watch should be posted.

D

Which alarm system is designed to provide notification to building occupants only on the immediate premises? Select one: a. Supervising station alarms b. Public emergency alarm reporting c. Emergency communications d. Protected premises (local)

D

Which aspect of fire protection with portable fire extinguishers is essential, but often overlooked? Select one: a. Size b. Training c. Extinguisher capability d. Extinguisher placement

D

Which class of fire involves energized electrical equipment? Select one: a. Class D b. Class A c. Class B d. Class C

D

Which component can consist of batteries with chargers, engine-driven generators with a storage battery, or multiple engine-driven generators? Select one: a. Initiating device b. Primary power supply c. Notification appliance d. Secondary power supply

D

Which dry-chemical agent is also known as ordinary dry chemical? Select one: a. Potassium bicarbonate b. Monoammonium phosphate c. Sodium carbonate d. Sodium bicarbonate

D

Which dry-chemical system component may contain both the agent and the pressurized expellant gas? Select one: a. Hydrants b. Actuating mechanism c. Nozzles d. Storage container

D

Which foam proportioner is one of the most reliable methods of foam proportioning? Select one: a. Pressure proportioning tank system b. Around-the-pump proportioner c. Coupled water motor-pump proportioner d. Balanced pressure proportioner

D

Which of the following statements about an Inspector I is MOST accurate? a. They are expected to perform plans review as a primary duty. b. They do not perform, nor do they need to be familiar with, plans review. c. They only perform plans review when an Inspector II is unavailable. d. They are not expected to perform plans review but must be familiar with the process.

D

Which statement about procedures for accepting field changes is MOST accurate? Select one: a. Once a plan is approved, changes cannot be made to that plan. b. An owner/occupant can make field changes without approval. c. The inspector is always allowed to approve field changes. d. The authority may rest solely with the fire marshal or building official.

D

Which supervising station is used to protect large commercial and industrial buildings, high-rise structures, and groups of commonly-owned facilities? Select one: a. Local b. Remote c. Central d. Proprietary

D

Which type of clean system agent is no longer produced but may still be in service? Select one: a. LITH-X® b. MET-L-X® c. NA-X® d. Halon

D

Which type of flame detector is effective in monitoring large areas such as aircraft hangars and computer rooms? Select one: a. Photoelectric detectors b. Combination detectors c. Ultraviolet detectors d. Infrared detectors

D

Which type of rate-of-rise heat detector can monitor large areas of a building? Select one: a. Pneumatic rate-of-rise spot heat detector b. Electronic spot-type heat detector c. Rate-compensation heat detector d. Pneumatic rate-of-rise line heat detector

D

Which type of specialty signal indicates loss of primary power or failure or removal of an initiating device? Select one: a. Alarm signal b. Alert signal c. Supervisory signal d. Trouble signal

D

Which verbal skill requires recognizing that the listener may have a different point of view? Select one: a. Showing respect for the feeling and thoughts of the other person b. Taking responsibility for personal feelings and thoughts c. Being aware of any special needs of the receiver d. Engaging in a dual perspective

D

proprietary system

Describe the type of system where alarms to different stores of the same proprietor are tied into on location.

What should an inspector do when an owner/occupant denies access to the property to be inspected? (704)

Document the action and follow departmental protocols for securing permission to obtain legal access

Verifying occupant loads and investigating complaints are examples of which Inspector I job duty? (689)

Enforcement

5

Dry standpipes are hydrostatically tested every ____ years.

What is the key to successfully handling any emergency, regardless of the type of occupancy? (716)

Effective execution of an emergency plan

What listening skill involves critically analyzing the message to determine how factual it is? (692)

Evaluating

How often do fire drills need to be done in a educational facility?

Every month while school is in session

Anecdotal evidence

Evidence that may or may not be true it is used to generalize when there is insufficient data

What are the 3 parts of means of egress?

Exit access, the exit and the exit discharge

Rate of rise detector depends on what?

Expansion if the heat and activated when rises 12 to 15 degrees per min

2

Exposed supports under storage tanks must be protected by fire resistant materials with ratings of ___ hours or more.

Which nonverbal communication skills require attention to cultural differences? (694)

Eye contact and proximity

Which element of the communication model completes the communication process? (691)

Feedback

What are the hazards of dip tank operations?

Fire involving liquids and explosions involving vapor and air mixtures

weekly

Fire pumps on standpipe systems should be tested by starting and running them ________.

What are the hazards of dip tank operations?

Fires involving liquids and explosions involving vapor and air mixture

How can an inspector overcome prejudice when listening? (693)

Focus on the message and not the sender

What is the first step in the burning process?

Fuel and oxygen mixed properly

What are two type of automatic roof vent designs?

Fusible link- can't operate below 300 F Drop Out Panel type

What type of electrical outlet should be installed in bathrooms?

GFCI or anywhere water is within 6'6' in kitchens

What is a butterfly valve?

Gate rates 90 degrees in water way Operates with a 1/4 turn and has a pointer arrow that shows the position of the valve

automatic

Halogenated agents are used in both total flooding and local application systems. Both types of systems require ____________ detection equipment for actuation.

Which of the following provides the BEST example of an occupancy with a complex emergency evacuation drill? (716)

Health care facility

What is a Bimetallic detector?

Heat detector using 2 types of metal which have different heat- expansion ratios. the 2 strips are bonded together and one expands faster then the other causing the combined metals to arc when subject to heat, Once arched sends a signal to system control unit and can be reset on its own

MORE THAN 60

How many gallons define a storage tank?

Visually = Weekly and Trip = AnnuallY

How often should a dry pipe system be inspected? Visually inspected ________ and trip tested ________.

What should inspectors display or have available for immediate review when arriving for an inspection? (703)

Identification

The most stringent

If a decision is to made on a State, Federal, or Local law, which would the Fire Inspector most likely choose?

BI-METALLIC

If a detector is fixed temperature and self resetting it is probably a _____________ type.

architect

If disputes about the construction arise, the __________________ has the final interpretation.

non-coded

In a zone _____________ system the alarm bell will give a constant alarm bell.

35

In order to give the required pressure at the bottom of a gravity feed tank, the pressure must be at least ____ feet above the highest head.

150

In pumping a sprinkler system, FD pumpers should develop and maintain a pressure of ______ PSI.

Direct costs

Include expenses that must be paid but would otherwise not have occurred without the programs such as printing supplies and fuel

What are 3 things the inspectors report should do?

Inform , analyze, and recommend

Which of the elements of a memo provides details regarding a topic? (696)

Information

Public Information

Information that it disseminated to the public .

Violation

Infringement of existing rules, codes, or laws

month

Inspectors should determine if competent personnel are making a visual check of wet-pipe sprinkler systems at least once a _________.

What do you use to do a water flow test to a sprinkler system?

Inspectors test valve

When communicating, what prevents the receiver from fully receiving a message? (691)

Interference

True

Is this statement TRUE or FALSE? Balloon Construction is defined as, "Continuous studs from sill to top plate"

True

Is this statement TRUE or FALSE? Components of alarm systems include a control panel, alarm initiating devices and power source.

TRUE

Is this statement TRUE or FALSE? Fire Resistance Rating is defined as, "The amount of time a material or assembly of materials will resist a typical fire as measured on a standard time-temperature curve."

True

Is this statement TRUE or FALSE? Halogenated agents are used to extinguish fires chemically and also to stop the combustion process itself by breaking the chemical chain reaction. They are not effective on fires involving fuels such as potassium or sodium, or on deep seated class A fires.

True

Is this statement TRUE or FALSE? Lintel is defined as, "A beam which spans an opening in a masonry wall".

True

Is this statement TRUE or FALSE? The three most commonly used sprinkler release mechanisms are fusible link, glass bulb and chemical pellets.

True

Is this statement TRUE or FALSE? Wythe is defined as, "Vertical section of a wall one masonry unit thick".

What should an inspector do if none of the violations have been corrected and no effort has been made by the owner/occupant to correct the violations? (715)

Issue a final notice with a date for another inspection

What does veneer do?

It approves appearance of a building and is non load bearing

What is a clapper valve?

It opens when the system flows water from the supply side and also opens the piping to the retard chamber

What is a retard chamber for?

It prefills with water during surges prior to allowing water to the electronic alarm preventing false alarms

What is a draw back of sand- line mortar ?

Its water soluble

What determines retention time for records? (697)

Jurisdictional policies and procedures

What serve as official records of an inspection and form the basis for legal action when required? (714)

Letters and reports

Three areas of interpersonal communication skills

Listening, Conversing, and Persuading

What is a load that weight is superimposed by the use and occupancy of the building ?

Live load

What is a impact load?

Loads applied to a building for a short period of time

What is a concentrated load?

Loads located at one point

What is a border line?

Located near the edge of the sheet of drawing paper and separate various portions of the drawing

6'8"

Means of egress shall be so designed and maintained as to provide adequate headroom. In no case shall any projection from the ceiling be less than ______ normal height from the floor.

What plans are HVAC systems usually shown on?

Mechanical plan

What basic element of a communication model gives the path that a message takes? (690)

Medium

What are hidden lines?

Medium weight and composed of short dashes and define edges and surfaces that are not visible in a particular view.

Which basic element of a communication model contains a meaning, idea or concept that a speaker is attempting to communicate? (690)

Message

What is a gusset plate?

Metal or plywood used to reinforce a joint or truss

What size piping and what supply is required for residential sprinkler systems?

Minimum of 3/4 in piping and domestic water supply with single household shut off

How often are fire service elevators tested?

Monthly

What is the spacing distance between tanks storing Class I, Class II or IIIA?

Must be 1/6 the sum of their diameters

NFPA 220

NFPA _________ governs types of Building ConstructioN

Deluge valve, Heat detector, Sprinkler heads.

Name the three main components of a pre-action sprinkler system.

Which task in Monroe's Motivated Sequence Pattern involves describing the problem and demonstrating a need for a change? (695)

Need

What must an inspector be prepared to deal with by business owner/occupants when they act on complaints? (724)

Negative attitudes

Can a inspector be held liable for acts they consider necessary to fulfill their responsibilities?

No

Do fire escapes stairs count as a means of egress?

No

Is a partition wall load bearing?

No

Is carbon steel used for cryogenic tanks?

No

Is plate glass considered safety glass?

No

The thickness of wood used for fire stopping is what?

No less than 2 inch

550

No two standpipes can exceed ______ feet.

What kind of communication is body language? (694)

Nonverbal

Body Language

Nonverbal communication including but not limited to body posture and gestures; represents a large portion of communication in human interactions

What is the hour rating of the roof in a dry cleaning facility?

Not less than one- hour

What is a common type of indicating valve

OS & Y

What are the 4 steps for performing the main drain test?

Observe , open, observe, and close

ONLY ITEMS IN VIOLATION

On follow-up inspections, what should be covered?

What is a veneer wall?

One made of single vertical thickness of masonry designed to improve the exterior appearance of a building

How do you test a wet system?

Open the main drain valve allowing alarm to activate. Take measurements of the water Before,during and after the test and compare the readings

What is a scupper?

Opening in the wall for the release of water from a roof or floor

What is the color of a frangible bulb of an ordinary sprinkler head?

Orange or red

Cease and Desist Order

Order prohibiting a person or business from continuing a particular course of conduct

What type of construction with exterior weight bearing walls have a 1 hr resistance rating?

Ordinary construction

Who is responsible for training employees in emergency evacuation of hotels and motels? (722)

Owner or administrator

Fire and life safety educators

Personel That teach fire safety messages to target audience

What unique conditions impact evacuation drills for correctional facilities?

Physical security features of the buildings and the need to maintain control of inmates.

What is a short column with a large cross section in proportion to its length?

Pier

10 PSI , 300 F

Portable tanks must be installed with an emergency venting device to lower internal pressure to ____PSI. If fusible vents are used, they must be designed to operate at a temperature not exceeding ______ °F.

What is a PIV?

Post indicator valve

What are the two common types of extinguishing agents in a hood system ?

Potassium Carbonate and potassium acetate

Purple K Powder (PKP)

Potassium bicarbonate is the chemical found in a ___________ extinguisher.

What is the best way to improve good listening skills? (693)

Practice

What type of sprinkler system will not cause damage if a pipe breaks?

Pre- action

Which of the following is the BEST example of a compliance issue that an inspector may check in an assembly occupancy after hours? (702)

Presence of locked, blocked, or obstructed exits

What does an inspector focus on during a follow-up inspection? (715)

Problem areas from the first inspection

What inspector practice goes a long way in providing education and building a positive image of fire prevention activities? (689)

Professional attitude

What should an inspector do to assist an owner/occupant in finding a solution to remedy a violation? (713)

Refer to the appropriate professional

What is another name for a pictorial drawing?

Rendering

What listening skill involves the feedback portion of the communication process? (692)

Responding

Balconies and Mezzanines with loads greater then 100 must have how many means of egress?

Same as a floor and not less then two

What is the floor plan?

Sectional view taken on horizontal plan 42" to 48" above the floor

What type of material is ineffective using halon?

Self oxidizing

Type of door required for flammable storage room ?

Self- closing

How often should a halon extinguishing system be tested?

Semi- annually

What is a exploded pictorial drawing ?

Shows relative position of parts or construction detail and clarifys assembly

NFPA 13

Standard for the Installation of Sprinkler Systems

NFPA 1031

Standards for professional qualifications for fire inspector

What is a common cause of electrical arcs?

Static electricity

What is Ashlar masonary?

Stone cut in rectangular units

What are the four basic components of a dry chem extinguishing system?

Storage tank, piping, nozzles, and the actuating mechanism

What is a internal force in a building which resists the load?

Stress and strain

What is the Stack effect?

Strong air flow patterns in vertical shafts of a high rise structure

What group of trusses are called the web?

Struts, ties, and panel points

75 psi

Tanks must be 2/3rds full at ____ PSI.

What is the Steiner tunnel test?

Test used to rate flame spread

erg

The __________ book lists the hazardous materials by names and four digit numbers.

RETARDING CHAMBERS

The ______________ is installed between the alarm check valve and the water flow signaling equipment.

What is Fire resistance ?

The ability of a structural assembly to maintain its load- bearing ability under fire conditions

Who has the ultimate authority to make changes in fire codes?

The authority having jurisdiction

What is the most critical thing for an inspector to check in a warehouse?

The automatic sprinkler system

Footer

The base of the foundation wall which is wider to provide a bearing surface is a ____________.

equal

The boiling point of a liquid is that temperature at which a vapor pressure of a liquid is _______ to the external pressure being applied to it.

Who should the inspector invite to accompany the inspector during the inspection? (704)

The building owner/occupant

What is the least important factor when evaluating storage of flammable liquids?

The container size

When building a new occupancy what is the date used in the effect code?

The date of plan approval

What is the discharge size of the inspector test connections?

The discharge orifice shall be in size to smallest sprinkler in the system

protective

The express purpose of ___________ signaling systems is to conserve life and property.

What is the chief characteristics of ordinary construction?

The exterior walls are made of masonary

potassium carbonate

The extinguishing agent known as wet chemical is an aqueous solution of _______________ .

1500

The highest GPM rating for a horizontal shaft fire pump in use today is ________________ GPM?

What is a ridge?

The horizontal member at the peak of the roof and the upper ends of the rafter are connected to it

DEAD LOAD

The load placed on a building as a result of its own weight and objects affixed to it is called _____________.

What is fire load ?

The maximum amount of heat that can be produced if all the combustible materials in a given area burn is.

500 gpm

The minimum water supply for a Class III system is ______ GPM for at least 30 minutes.

resistor device

The most common of monitoring devices in alarm systems for measuring the current flow between two wires is called a ______________.

school

The most likely place to find a master coded system would be a ______________.

perspective

The most realistic type of pictorial drawing and the one used for artists renderings is a ______________ drawing.

What is a bond?

The pattern which masonry units are laid

Which type of drawing has the most realistic view?

The pictorial drawing

floor

The plan which provides the largest amount of information about the proposed structure is the __________ plan.

Public education

The presentation of a safety message with the sole goal of reinforcing good behavior's or changing undesirable behaviors in order to make the community safer

275

The requirements established in NFPA 14 specifies that standpipe systems shall be limited to _______ feet in heigHT

What is the horizontal measurement on stairs called?

The run

1/6 the sum of their diameters.

The spacing between two storage tanks should be at least ____ feet for tanks containing liquids classified as class 1, 2, or 3A, the distance between the tanks must be at least ___________________________________ .

OUT

The stem on the O.S.&Y. valve is ____ when it is open.

Boiling point?

The temperature at which the vapor pressure of the liquid is equal to the external pressure applied to it

What is Vellum?

The transparent paper original drawing are made on

ISOMETRIC

The type of drawing which is sometimes called a multi-view drawing or an unfolded box is the ___________ drawing.

BALUSTERS

The vertical stair members that support the hand rails on a set of stairs is called ______________.

DEAD

The weight of the building and any equipment built in is considered to be a _________ load.

What is a dead load?

The weight of the building itself and and equipment attached permanently

Which of the following statements is MOST accurate regarding computer records? (698)

They greatly increase efficiency and accuracy in records management and retention

Indirect cost

Those cost that the fire department would have incurred whether the program exists or not

What determines whether an inspection is effective or not? (698)

Time spent reviewing the structure or facility inspection records

What is the purpose of a life safety code?

To provide minimum requirements for life and safety from fire and similar emergencies

Plates

Top and bottom horizontal members that run above and below studs are called ________.

What are requirements for fire apparatus extinguishers?

Two rated for class B:C fires- 1 dry chem rating of 80 BC 1 CO2 of at least 10 B:C One rated for class A fires and 1 2 1/2 gallon of water

What type of mortar is for underground masonry?

Type M

What will a review of the inspection records file reveal about an upcoming inspection? (701)

Types of hazards that may be present

Which listening skill consists of decoding a message and assigning meaning to it? (692)

Understanding

What defines educational occupancies?

Used for educational purpose, 6 or more people, up to grade 12, more then 4hrs per day or 12hrs per week

What is chipboard?

Used it floors in mobile homes and is wood chips glued together to make flat sheets

Why are follow-up inspections conducted?

Verify that corrections noted in the inspection report have been completed.

Which tasks in emergency planning fall under the jurisdiction of an inspector I?

Verifying that emergency plans are in place and in compliance with locally adopted codes

What is the most difficult aspect of dealing with people while conducting an inspection? (713)

Violation discussions

Which task in Monroe's Motivated Sequence Pattern includes describing the solution for the problem and how it will benefit the listener? (695)

Visualization

W12X16 on structural steel means what?

W- type beam, 12- nominal depth , 16- weight per linear foot

What is a WPIV?

Wall post indicator valve

What does a chase do to a masonry wall?

Weaken it

Fire pumps for standpipes are tested and ran how often?

Weekly

How often are pumps tested and run for standpipes?

Weekly

What is another name for potassium Carbonate?

Wet Chem

annually

Wet pipe sprinkler systems require testing _____________.

monthly

Wet pipe sprinkler systems should be visually inspected ___________.

6

Wet standpipe systems should be inspected every ___________ months.

Construction where walls are masonry

What are the characteristics of ordinary construction?

Endothermic

What are the properties of Gypsum Board and Dry Walls?

blue

What color is a high temperature sprinkler head painted?

Lally columns

What is a column filled with concrete referred as?

Compression

What is a crushing force?

CARPET TESTING

What is a radiant flux test used for?

5 gallons

What is the maximum allowable size for an approved safety can?

15 psi

What is the minimum pressure of a sprinkler head?

green

What is the missing hydrant color? Blue - 1500+ GPM _______ - 1000-1499 GPM Orange - 500-999 GPM Red - Below 500 GPM

1/2 inch

What is the standard orifice size on a sprinkler head?

400-475 Very Extra High

What temperature rating and classification is a green sprinkler head?

Halon

What type of extinguishing agent is recommended for areas of high value sensitive equipment?

partition

What type of wall can be used as either a load bearing or a non-load bearing wall?

Cantilevered

When a beam is supported only at one end it is said to be ________________.

Scales of 1 to 10

When creating a matrix Use a rating scale with these numbers , to give the relative degree of frequency Then each problem is plotted by its severity on the vertical axis, again using a scale of

When is photographic documentation particularly helpful regarding an inspection? (708)

When documenting violations that may result in a citation or legal action

what is a fire cut?

When the end of a joist is cut off at a angle to permit the joist to fall out of the masonry wall without damaging the wall

owner of the property

Who is responsible for the maintenance of the sprinkler system?

What is the maximum travel distance for a class D extinguisher?

Won't exceed 75 ft same for class A

What is a chipboard?

Wood chips glued together to make flat sheets

What is a simple beam?

Wood joist spanning from wall to wall

Is exit access permitted through dining rooms and sitting rooms?

Yes but not through kitchens or storage rooms

automatic

________________ sprinkler systems are now recognized as the most reliable of all fire protection devices.

rate of rise

_________________ detectors respond to quick changes in temperature rather than activating at a fixed temperature. They have a small chamber filled with air. If rapid heating occurs however, the air inside the chamber expands.

What is a girder?

a beam that supports another beam

Conversations that involve the exchange of detailed information or complete concentration should take place in: (691)

a controlled environment

What is a hip rafter?

a rafter that extends from an outside corner of a building to the ridge board, usually at 45 degrees to the ridge

How are dimension lines measured?

a minute is 1/60 of a degree a second is 1/60 of a minute

What is a atrium?

a opening through a series of floors for the purpose other than a enclosed stairway. 6' 8" from the floor

What is a short, squat column called?

a pier

What is a booster pump?

a pump that takes from a low pressure municipal main and boosts the pressure to levels required for fire suppression systems.

Follow-up inspections are made to verify that corrections noted in the inspection report have been: (715)

completed

What temperature does steel begin to fail?

above 1000 degrees

What is passive fire defense?

active sprinkler systems and fire doors/ walls

Ideally, inspection records should be maintained for ____ properties or facilities within a jurisdiction. (697)

all

Emergency evacuation drills should be conducted in: (716)

all types of occupancies

Where are standpipes located?

any part of floor within 130' reach (100'for hose, 30' stream) Must be in non-combustible fire rated walls

How many fire alarm pull boxes should their be on multistory buildings?

at least 1 per floor

What are mounting requirements for fire alarm pull boxes?

bottom no less then 3 1/2' from the floor and no more then 5'vertically from the floor level to the activating handle or lever

What are the 5 categories of heat energy?

chemical, electrical, mechanical, nuclear, and solar

The key to successfully handling any emergency, regardless of the type of occupancy, is: (716)

effective execution of an emergency plan

What are 3 types of fire pump drivers?

electric motor, diesel motor and steam turbine

What is a benchmark?

elevation of a plot plan

Fire exstinguishers of 150lbs or less should be hydro tested how often?

every 12 years

When should extinguishers be hydro tested?

every 5 years unless dry chem less then 150 lbs made of steel every 12 years

When discussing violations, nothing erodes an owner/occupant's confidence in an inspector more than: (713

finding a mistake

What is a class III standpipe geared too?

fire personnel and occupants

What is a Class I standpipe geared too?

fire personnel only

What type of buildings are standpipes needed in?

greater then 75' to the highest occupied floor large one-story buildings( horizontal )

What is the bottom chord of a truss?

it is similar to rope and is under truss under tension

Complaints that involve a serious life safety threat require: (722)

immediate action

An inspector should process and act upon each complaint: (722)

in a consistent manner

What is a sectional line?

in a sectional view to show where the material has been cut by a cutting plan. Also called cross- hatched lines

When communicating, the greatest distraction is the listener's: (693)

internal voice

What is a hip jack?

it extends from the top plate of the building to the hip rafter

What is a cold flow?

its caused by repeat heating of a sprinkler head to near its operating temp . Its sliding apart of the fusible link of a sprinkler head

What is a flitch plate girder?

its made by sandwiching a piece of steel between 2 wooden beams

What is a axial load?

its perpendicular to the plan of a section/ its a force that passes through the centroid of the section under consideration. A structure will sustain its greatest load when it is axil

Whats a disadvantage of a dry chem extinguisher?

its residue makes a clean up problem

What temperature flash point is a flammable rating?

less then 100 degrees. 100 and above is combustable

What is a pressure relieving valve?

must be in any outlet with greater pressure then 100psi

NFPA requirements for PRV?

must limit outlet pressure to 100psi

A large portion of inspector communication involves: (692)

listening

How are sprinkler valves kept in the open position?

lock chain or other locking mechanism or electronic detection device

amps-

measures the QUANTITY of electricity

OHM-

measures the RESISTANCE of electricity

What is the discharge range for pressurized water extinguishers?

minimum discharge range of 30' for a 40 sec period

What is the discharge range for dry chem and dry powder extinguishers?

minimum horizontal range of 10'

When should you test a wet system?

monthly by a in plant inspector

How often are fire service elevators tested?

monthy

Is there such a thing as a paint plan?

no

Why does solid piling storage present fewer paths for fire development?

no horizontal voids and due to stacking merchandise directly on top of eachother

What is the fire resistance rating of a exit door in buildings of 3 stories or less?

not less then 1 hour

What is a class II standpipe geared for?

occupants only

Usually, all e-mail messages that are written by public officials during the performance of their duties are: (696)

official documents

The emphasis of emergency evacuation drills in educational facilities is placed on: (718)

orderly evacuation

An exhausted released air to where?

outside atmosphere

What is a exploded pictorial drawing?

parts of an assembly are separated to better illustrate the assembly process

What does a P stand for on NFPA Placards?

potential for the material to go through auto- polymerization

The best way to improve good listening skills is to: (693)

practice

When planning for an inspection, the first consideration for an inspector is to: (701)

prepare to conduct the inspection safely

Primarily, administrative duties for inspectors include: (695)

preparing written communications

What is a check valve?

prevents reverse flow of water to prevent it from entering the water system which limits it to one direction

How often are sprinkler systems tested?

quarterly

Emergency evacuation drills in health care facilities are conducted: (719)

quarterly on each shift

True

s this statement TRUE or FALSE? Halon is rated as being less toxic than CO2.

What is a fine aggregate usually made of?

sand

To determine whether an administrative warrant to enter a location is needed, an inspector considers the type of occupancy, location within the occupancy, and: (724)

severity of the nature of the complaint

What is the outer weather surface placed over sheathing called?

siding

What are some key notes to Parallel Perspective drawings?

similar to oblique drawings, the true shape and size are shown in the front view

what are common dry chem agents?

sodium bicarb, potassium bicarb, and mono ammonium phosphate

What is a lintel?

support for a masonry opening, usually made of steel or a special form, such as pre cast concrete

When inspecting areas that involve noisy operations, it may be necessary to: (691)

take notes

What is a mushroom cap?

tapered extensions at the top of columns which transfer loads from the floor to the column

Where on a plan are symbols identified?

the legend

what is a diameter?

the length of a line running between 2 points on the circle passing through the center

The success of an inspection visit depends upon how familiar an inspector is with: (698)

the site being inspected

How must a extinguisher be mounted if weighing 40lbs or less?

the top must be no more than 5' above the floor

How must a extinguisher be mounted if weighing more than 40 lbs?

the top must be no more than 5' above the floor and the bottom can't be no closer then 4' to the floor

What is the difference between interior and exterior plywood?

the type of adhesive used

What are most spot welds specified by?

their diameter

Heat detectors

they are limited and slowest type of systems but are reliable due to their sensitivity

What are dimension lines?

they extend the length of distance being measured. extension lines are drawn perpendicular

Proper mounting for 40lbs or more extinguishers?

top no higher then 3 1/2 ' from the floor

Proper mounting for 40lbs or less extinguishers?

top no higher then 5' from the floor with floor clearance no less then 4"

What is the proper order to inspect a building?

top to bottom, bottom to top, follow plant process from beginning to end

What happens to marble when subject to heat?

turns to chalk

What is a circuit?

two or more conductors carrying electricity from the source to the electrical device and returning

Explain Halon Extinguisher systems?

used for delicate electrical equipment, not for Class a fires and it must be tested semi annually

What is a draft curtain?

used to limit the mushrooming effect of heat and smoke

What happens during a dust explosion ?

usually followed by a bigger one and happens in sequence

The amount of time it takes to conduct an inspection: (701)

varies for each facility and occupancy

The class B rating test?

very sq ft of fuel corresponds to every 1-b rating

How often are fire pumps for standpipes tested?

weekly

what is axial load?

when all conditions are equal, a structure will sustain its greatest load

When is a pre action system used?

when its important that water damage is prevented, even if the sprinkler pipe break accidentally

An inspector needs to be proficient in various types of: (695)

written communication

Can a inspector be held liable for the manner in which they perform or act?

yes


Conjuntos de estudio relacionados

Chapter 33 & 34 - Animal Diversity and Invertebrates

View Set

Yo, Tu, Ella/el/usted, Nosotras/nosotros, Vosotras/Vosotros, Ellas/ellos/ustedes

View Set

Prioritization, Delegation, and Assignment Chapter 16

View Set

Influence dans les groupes : principes fonctionnalistes classiques

View Set

Hurst (Readiness Exam #4), Hurst (Readiness Exam #3)

View Set