Intermodal Dry Cargo CNTR/CSC Reinspection (Cert)

In the image below, which marking represents the container's size and type?

2210

May 2018 (30 months from previous inspection)

According to the DD Form 2282 decal shown below, when was this container last inspected?

When inspecting containers, what tool is used to move containers by lifting them at the corner fittings?

Container handler

Which lettered entry block should be marked for the container discrepancy: Dent 2 inches deep on left top side rail (Major)?

D

What form is used as a permanent record of each container inspection?

DA Form 2404

Located in the MIL-STD-3037 appendix, what form is used to ensure each container inspection is conducted in a thorough, systematic manner?

DD Form 2282 decal

Which defect listed below prevents a side-opening container from being used to transport bombs? Refer to MIL-STD-3037, Section 4 as required.

Dent in door header 3/16" deep and 3" long

Which of the following containers is the most commonly-used by all military branches to ship general purpose dry cargo?

End-opening

When inspecting containers, what tool would you use to inspect the container floor for excessive gaps?

Feeler gauge

Which of the following containers is used for large, heavy cargo that cannot be loaded into a container with fixed sides or walls?

Flatrack

Select the appropriate defect classification for the container defect: Door sill has 7" splice on left side. Refer to MIL-STD-3037, Section 4 as required.

IMDG Major

What must be displayed on both ends, both sides, and the top of a container?

ISO Identification Markings

Which part of the container door assembly is highlighted?

J-bar

What is the primary reference used by inspectors to conduct CSC container inspections?

MIL-STD-3037

Which statement is true?

MIL-STD-3037 has separate paragraphs that document IMDG and non-IMDG criteria.

Where do you find the container inspection checklist for a mobile facility?

MIL-STD-3037, Appendix A

When inspecting containers, what tool would you use to inspect a container's alignment?

Measuring Tape

Select the appropriate defect classification for the following container defect: Dent 3/16" deep on the road side panel. Refer to MIL-STD-3037, Section 4 as required.

Minor

Which statement about minor defects is true?

Minor defects are documented and/or repaired at the inspector's discretion.

Which of the following containers is integrated with electrical service and utility equipment?

Mobile facilities

Select the appropriate defect classification for the container defect: Cracked lower rear roadside corner fitting. Refer to MIL-STD-3037, Section 4 as required.

Non-IMDG Major

Which of the following containers has a removable tarp in place of a rigid roof?

Open-top

*Remarks Section*

Select the section where descriptions of each defect are documented on this container inspection checklist.

You inspected a container in April 2020. When is that container due for reinspection?

September 2022 (30 months from previous inspection)

Which of the following containers allows for easier loading and unloading of large bulky stock, such as bombs?

Side-Opening

Refer to DA Form 2404 below. What is the appropriate entry for Item #5 in this example?

Unserviceable for IMDG and Non-IDMG

When inspecting containers, what tool is used to determine weld serviceability and the severity of corrosion?

Welder's Hammer

When is a new DD Form 2282 decal required?

When the existing 2282 is due to expire within 30 days

Forklift Pocket

Which container component is highlighted?

Gooseneck Tunnel

Which container component is highlighted?

Threshold Plate

Which container component is highlighted?

Top End Rail

Which container component is highlighted?

Crossmembers

Which container component is shown?

Cam and retainer

Which part of the container door assembly is highlighted?

A container with a major IMDG defect may be used to transport...

general cargo only

Containerization is a shipping method in which a large amount of material is packaged into...

large standardized containers

What is the maximum allowable depth of a door header dent? Refer to MIL-STD-3037, Section 4 as required.

¾" for IMDG, 1-⅜" for general cargo