MSSC Test 2 (Through Tolerencing)

¡Supera tus tareas y exámenes ahora con Quizwiz!

Which dimension would be placed directly to the right of a fillet weld symbol?

Length

What is the difference between local and general notes on a blueprint?

Local notes apply to specific items or areas, while general notes apply to the entire drawing

Internal dimensions, like holes, are at their MMC when they are at their __________ of their tolerance zone?

Lower limit

What symbol means maximum material condition in geometric dimensioning and tolerancing?

M in a circle

The basic dimensions shown on a print are called __________ dimensions.

Nominal

0.001 is __________.

One thousandth

Which weld symbol indicates a weld made by joining two members that overlap with one or both of the members having holes?

Plug and slot

__________ welds are used to connect two plates using holes in one or both plates to allow access for the welding tool.

Plug and slot

What type of drawing defines how the product is going to be manufactured?

Process drawing

What is a datum?

Reference point

Which information is NOT included in a materials block?

Revision number

A weld's contour is the shape of the weld's surface and can be everything below, EXCEPT __________.

Round

In a feature control frame there is a symbol, a number, and a letter. What does the number represent?

The total amount of tolerance for the geometric feature

How are datums identified on the process drawing?

They are identified with a capital letter

The weld symbol for the other side is always on what side of the reference line?

Top

What is a revision number in the title block of a blueprint used for?

Tracking each time there is a change to the drawing

The tolerances that are included in a tolerance block can vary from drawing to drawing. Is this statement true or false?

True

When the same type of arc is used in more than one place, what note is included with the dimension?

Typical (TYP)

Which supplementary weld symbol consists of a circle placed around the joint where the reference line and the leader line meet?

Weld-all-around

The three most basic dimensions identified on drawings are __________.

Width, depth, and height

The specification for parts being produced at a workstation is 1.842 ± .005. Is a part that has been produced at 1.836 out of spec?

Yes, it is out of spec

Sixty minutes of arc is equivalent to how many degrees?

1

If a product feature has a dimension of 1.8 ± .03, what is the lower tolerance dimension?

1.77

How is a half scale drawing written?

1:2

The weld symbol __________.

Indicates the type of weld the welder is to make

What area on a drawing contains more information than print notes?

Information block

Which type of fit is used when there is to be no movement between the parts?

Interference fit

Counterbore holes are best described by which of the following statements?

A counterbore hole has an enlarged opening in the top

Each linear dimension on a part will have __________.

All of the above

What is the difference between allowance and clearance?

Allowance is the tightest possible fit, while clearance is the loosest possible fit

What two organizations set the standards for welding symbols?

American National Standards Institute and American Welding Society

Basic and exploded view are two types of __________ drawings.

Assembly

Which type of drawing shows the product as it should be put together with all of its parts in their operational positions?

Assembly

Which type of dimensioning uses a common reference point?

Baseline dimensioning

What integers can be used to dimension the measurement of an angle?

Both B and C

Where are revisions that are made to drawings tracked?

Change block

What does the symbol below illustrate?

Concentricity

The finish symbols and __________ symbols indicate how the weld should appear when the welding operation is complete.

Contour

Which type of hole allows the head of a fastener to rest on a flat surface below the outer surface of the part?

Counterbored

The use of a center line plus the diameter symbol indicates that a part is __________.

Cylindrical

Tolerance is the total amount by which a specified __________ is allowed to vary and still be a good part.

Dimension

Identify the feature indicated by the arrow.

Dimension line

Which method of tolerancing places the tolerances next to each dimension?

Direct

What information is provided by the basic surface finish symbol shown?

Do not remove material

Of the five geometric features that are commonly toleranced, which describes the shape of a plane or circular type surface of a part?

Form

What is used to define parts based on how they function?

Geometric dimensioning and tolerancing

What refers to tolerances that control form, profile, orientation, location, and runout?

Geometric dimensioning and tolerancing

Which dimension is placed between the rays of a V-groove weld symbol?

Groove angle

Which of the two drawing standards is always specified with a letter A followed by a number?

ISO

A part measuring 44.85 mm in a process with a tolerance of 45mm +/- .28 is considered __________.

In spec (within the tolerance range)

Which of the following drawing dimensioning guideline is incorrect?

Include every possible dimension


Conjuntos de estudio relacionados

Professional Review Guide RHIA/RHIT CH 16

View Set

Module 11: Financial Statement Analysis

View Set

Modern Database Management - Self Check 03

View Set

Chapter 16 Video Case: Talking About Strengths and Weaknesses -- Interview 1

View Set

Chapter 3 (Math) Section 3A study set.

View Set

Chapter 3: Physical & Cognitive Development in Infants and Toddlers

View Set