Power Supply Facts
Convert AC power to DC power
AC (alternating current) is the type of current distributed through wall sockets. The voltage alternates between a negative and a positive charge, which is good for appliances requiring a high current. DC (direct current) is the type of current used inside a computer. Negative particles are drawn toward a positive charge, creating a unidirectional current flow. This type of predictable reliable current is ideal for an application where a lower current is required.
Aid in thermal management
All ATX power supplies have a fan that cools the unit. The fan direction pulls cooler air from the front of the case and blows hot air out the back.
8-pin EPS12V CPU power
Modern processors consume even more power. The 8-pin EPS12V connector provides four lines of 12 V power. The 8-pin EPS12V was originally used with some older dual processor systems. All modern multi-core processors use this connector. Some power supplies have two 4-pin connectors (4+4) that are meant to be used side-by-side in the 8-pin plug.
6+2-pin PCIe
Newer video cards require more power than can be supplied through the PCI Express bus. The 6+2-pin PCIe connector plugs directly into the video card to supply additional, dedicated power. The 6+2-pin PCIe: Provides up to 150 watts Is also known as a PEG6+2 (PCI Express Graphics 6+2 pin) Some motherboards have only a 6-pin PCIe connector. These connectors provide up to 75 watts.
You should be aware of the following facts about power supplies:
Power supplies should be matched to the motherboard and case form factor (i.e., match an ATX power supply with an ATX motherboard or a microATX power supply with a microATX motherboard). Some power supplies have a voltage switch that toggles between two voltage settings. Depending on the country, typically, the voltage switch can be toggled either between 115 and 230 volts, or between 110 and 220 volts.115 volts is used in North America.230 volts is used in Europe.100 volts is used in Japan.220 volts is used in most parts of Asia. Many power supplies have a switch on the back that turns the power on or off. Power supplies are rated in watts. A power supply's watt rating determines its maximum power output. To determine a computer's power requirements, use the following method:Find the watt requirement for each component by multiplying volts by amps (W = V × A).Add each value together to find the total watt requirements. ATX power supplies provide soft power, even when the computer is turned off, the motherboard has power. Soft power allows the computer to be turned on and off by the operating system or over the network.
Provide components with the correct levels of DC voltage
Standard ATX power supplies provide + 3.3 volts, +/- 5 volts, and +/- 12 volts of DC power. Most modern components require +12 volt output. Each separate voltage output circuit is referred to as a rail and can power multiple devices. To avoid overloading one circuit, many newer power supplies have two or more +12 volt rails. These are known as dual rail power supplies. Separate rails balance the power load between multiple circuits, preventing any one circuit from becoming overloaded.
4-pin 12 V (P4) power
Starting with the Pentium 4 (P4) processor, CPUs required more power than could be provided through the ATX power plug. The 4-pin 12 V connector: Connects to the motherboard Provides two dedicated 12 V wires to the CPU (Older processors only used 5 V power)
When troubleshooting a power supply, keep the following in mind:
Symptoms of bad power supply include:The computer does not turn onThe computer sporadically shuts off or rebootsA broken or noisy fan Before opening up the computer, rule out the obvious. Make sure:The power cord is plugged into the wall.The power switch is in the on position.The voltage switch is set to the correct voltage. Test the power supply using a multimeter or power supply tester. Voltage levels should be within +/- 5% of normal. If they aren't, the power supply is bad or failing and should be replaced.12 V rail should be between 11.4 and 12.6 volts.5 V rail should be between 4.7 and 5.25 volts.3.3 V rail should be between 3.1 and 3.4 volts. Because power supplies carry dangerous levels of electrical current, always take proper safety precautions.Never ground yourself when working on a power supply.Never open or disassemble a power supply. Always replace the entire unit.
24-pin (20+4 pin) ATX connector
The 24-pin ATX power plug supplies power to the motherboard. Some 24-pin connectors have one 20-pin plug and a detachable 4-pin plug. This allows for backwards compatibility with 20-pin motherboards. You can plug a 24-pin ATX power plug into a 20-pin motherboard connector, leaving the four pins unconnected.
4-pin mini-Molex
The 4-pin mini-Molex connector provides both 5 and 12 volts and is used by floppy drives.
4-pin peripheral power
The 4-pin peripheral power connector (colloquially called a 4-pin Molex connector) is used by legacy components (e.g., IDE hard drives and PATA optical drives), case fans, and other accessory devices. The connector provides both 5 V (red wire) and 12 V (yellow wire). Each power supply cable typically has multiple 4-pin connectors on the same cable. When connecting devices, try to balance the devices connected to each cable.
SATA power
The SATA power connector has 15 pins and provides 3.3, 5, and 12 volts. As its name implies, it powers SATA devices. You can use a special adapter to convert a 4-pin peripheral power connector to a SATA connector. When using an adapter, or on some power supplies, the connector supplies only 5 and 12 volts.
