TCP chpt 9 and 10 quiz

What is the administrative distance of the RIP routing protocol? a. 120 b. 1 c. 90 d. 110 e. 100

a

The command show ip protocol is used on a router to do which of the following? a. Display the routing protocol that can run on the router b. Display the IP address of the routers running an IP protocol c. Display the routing protocol running on the router d. None of these answers are correct

c

What is commonly called an Alias in DNS? a. A PTR record b. An MX record c. A CNAME record d. An NS record

c

which of the following does the OSPF routing protocol use to verify that a link between two routers is active and the routers are communicating? a. LSAs b. ARP messages c. Ping d. "Hello" packets

d

The command for enabling EIGRP on a router is A. router IGRP (as number) B. router EIGRP C. router EIGRP (as number) D. router EIGRP enable )

c

What is the administrative distance for OSPF in Cisco networking? a. 10 b. 90 c. 110 d. 120

c

RIP permits a maximum of 15 hops to prevent what? a. Routing metrics b. Routing table exchanges c. Bandwidth issues d. Routing Loops

d

What DNS record specifies the email server of the domain? a. PTR b. CNAME c. TXT d. MX

d

What router command will show whether the router is exchanging routes? a. show run b. show ip int brief c. show list d. show ip route

d

Which comand is display after issuing the command to enable RIP routing? a. Router(config-router-rip)# b. Router(config-router) c. Router#(config-router) d. Router(config-router)# e. Router#(config-router-rip)

d

Rip routing has been enable on the router. Which command is issued to use RIP routing to a host computer with an IP address of 192.168.20.0 a. Router(config-router-rip)# network 192.168.20.0 b. Router(config-router)# network 192.168.20.0 c. Router(config)# network 192.168.20.0 d. Router(config-router)# network 192.168.20.3 e. Router(config)# network 192.168.20.3

b

This international standard enables high-speed data transfer over the cable systems? a. DCC b. DOCSIS c. SYSDOC D. SYSLOG

b

What is the administrative distance for EIGRP in Cisco networking? a. 10 b. 90 c. 110 d. 120

b

What is the administrative distance for a directly connected route in Cisco networking? a. 1 b. 0 c. 10 d. 20

b

What is the number 10 in the command router ospf 10? a. Tag b. Process ID c. As number d. Metric

b

What is the number 150 in the command router eigrp 150? a. A Process ID b. An autonomous tag number c. A metric d. A tag

b

What is the purpose of variable length subnets? a. They are not recommended in modern computer networks. b. They minimize wasted IP address space when interconnecting subnets c. They reduce the numbers of bits required in a subnet mask from 32 to 24 d. They are the same as classful addressing

b

What is the router command to enable the RIP routing protocol on a router? a. config router RIP b. router rip c. rip 10.0.0.0 d. network 10.0.0.0

b

What is the router command to enable the RIP routing protocol on a router? a. config router rip b. router rip c. router rip [area] d. router rip [as number]

b

Which is the router command used to copy the running-configuration to NVRAM ? a copy run tftp b. copy run start c. copy run flash d. copy run show

b

Which of the following best characterize OSPF's Area 0? a. Used to hide data packets b. Root or the backbone for the network c. Inverse mask bits d. Route selection bits

b

Which of the following best characterize areas in the OSPF protocol? a. Not used b. Used to partition a large network into small networks c. Used to combine small networks into one large network d. An inefficient use of bandwidth

b

Which of the following best defines how areas are used in OSPF protocol? a. Areas are not used b. Used to partition a large network into smaller networks c. Used to combine small networks into one large network d. An inefficent use of bandwidth

b

Which of the following commands enable you to view the route codes and router? a. show ip router b. show ip route c. show routes d. show static routes

b

Which of the following is a key issue of link state protocols? a. send updates every 90 seconds b. send updates when routing changes c. use link lights to establish adjacencies d. use hop count metric to determine the best route of destination.

b

Which of the following router commands could be used to display the routing protocol configured on the router? a. router> sh ip protocol detail b. router# sh ip protocol c. router# sh protocol d. all of these answers are correct

b

Which of the following is an advantage of peer-to-peer network (select two) a. Poor security b. No centralized network administrator c. Easy to set up network d. Users must administer their own network e. Resource sharing

b,d

The BOOTP protocol is characterize best by which of the following? a. It enables computer to broadcast their own IP address b. It enables computers to discover their own MAC address c. It enables computer to discover their own IP address d. It is outdated and no longer in use

c

The command "show ip route" is used on a router to do which of the following? A. Set a static route B. Configure a static route C. display the configured routes on a router D. Display how often routing updates are sent

c

What happens if a DHCP server is not available? a. the client will issue a global boradcast to search for available DHCP server. b. The host computer will issue a unicast packet to the 169.254.1.1 address and then obtain an IP address. c. A DHCP client will use a self-assigned IP address known as Automatic Private IP Addressing (APIPA). d. The Ipconfig/redo command is automatically issue to establish connectivity

c

What is the administrative distance of a static route? a. 110 b. 120 c. 1 d. 90 e. 100

c

What type of networks might be used in a very small office where very basic file and print sharing must be used? a. Client/sever b. Private cloud c. Peer-to-peer d. Hybrid cloud

c

from which prompt is the command to specify rip routing issued? a. Router(Config) b. Router(config)> c. Router(config)# d. Router(config-router-rip)#

c

which of the following commands display the router's running-configuration? a. router> show ip running-configuration b. router# show rip rip running-configuration c. router# show running-configuration d. router# show configuration

c

The command to enter the router's global configuration mode is which of the following? a. router> conf t b. router> configure t c. router(config t)# d. router# conf t

d

What command can be used to verify EIGRP is running on the router? a. show run b. show ip int brief c. show history d. show ip protocol

d

What is the administrative distance for RIP in Cisco networking? a. 10 b. 90 c. 110 d. 120

d

What is the router command for displaying the startup configuration? a. show run b. show flash c. show history d. show start

d

Which command will display the configure routes on a router? a. show run b. show ip int brief c. show list d. show ip route

d

Which of the following command can be used to display the routes configured on the router? a. router> shoe route b. router# show route c. router# show rip route d. router# show ip route

d

Which of the following is an example of a classful address? a. 10.10.0.0 b. 192.168.0.0 c. 10.1.0.0. d. 10.0.0.0

d

EIGRP stands for which of the following a. enhanced interior routing protocol b. enhanced interior gateway routing protocol c. enhanced internet gateway routing protocol d. none of these answers are correct

b

In DHCP data packers, a DHCP discover packet is a. Message=Discover b. MT=Discover c. Discover=Type d. Type=Dsicover

b

Areas in OSPF Protocols are a. not used b. used to Partition a large Network into smaller Networks c. used to combine small networks into one large Network d. an inefficient use of bandwidth

b

A DHCP server isn't available.What process allows a windows system to automatically configure its IP address and subnet mask? a. IPhelper b. ReverseDHCPlookup c. APIPA (Automatic Private IP Addressing) d. none of the above

a

A static Route is enter from which command prompt a. router(config)# b. router(config#) c. router# d. router> e. router(config-static)#

a

The command used to display the router's current running configuration is what? a. show run b. show routing c. show interfaces d. show controller e.sh config

a

What is an international standard that enables high-speed data transfers over a cable system? a. DOCSIS b. DSLAM c. VDSL d. SONET

a

What is the command used to display the router's current running configuration? a. show run b. show routing c. show interfaces d. show controllers

a

What is the pointer recorded in DNS? a. It is a reverse record (a mapping of an IP address to a hostname) b. It is a mapping of a hostname to an IP address c. It is a record to locate a mail server d. It is a record to locate an LDAP server

a

Which is not an advantage of OSPF? a Very easy to implement b. Uses VLSM c. Link state changes are immediately reported d. Not a proprietary protocol

a

Which is not an advantage of peer-to-peer networks? a. Centralized network security b. Easy to setup c. Low cost d. User-controlled resource sharing

a

Which of the following best characterize variable-length subnet masks? a. Minimize wasted IP address space when interconnecting subnets b. are not recommended in modern computer networks c. Reduce the number of bits required in a subnet mask from 32 to 24 d. are the same as classful addressing

a

Which router command can be used to check weather the router interfaces are properly configured? a. Router# show ip interface brief b. Router> show interface ip brief c. router(config)# show ip interface brief d. Router(config-router)#show interface ip brief

a

variable-length subnet masks a. minimized wasted IP address space when interconnecting subnets b. are not recommended in modern computer networks c. reduce the number of bits required in a subnet mask from 32 to 24 d. are the same as classful addressing

a