3.9.6 Practice Questions

Pataasin ang iyong marka sa homework at exams ngayon gamit ang Quizwiz!

Which of the following is an error detection technique that can also correct the error?

ECC Error Correcting Code (ECC) can detect and correct errors. Parity error detection techniques can detect errors, but cannot correct them. The data must be resent. EDO is not a type of error detection, but a type of memory that can start a new access cycle while keeping the data output of the previous cycle active.

Which of the following is an error detection technique that can detect errors with only one bit?

Parity Parity error detection can only detect errors with only one bit, while Error Correcting Code (ECC) can detect errors with more than one bit. EDO is not a type of error correction, it is a type of memory that can start a new access cycle while keeping the data output of the previous cycle active.

You just replaced the motherboard, CPU, and memory in your computer. Now your computer will not start. You press the power button on the system case, but nothing happens; there are no sounds or lights. What should you do?

Connect the power button to the motherboard. The system case power button connects to jumper pins on the motherboard. When you press the power button, the cable sends the power on signal to the computer. If the power button was connected, you would typically hear fans start up and see lights come on as the system boots. Even without a processor fan, memory, or a keyboard or mouse, you would still see or hear something if the system had power.

You are attempting to boot a new system. The boot fails, and the system sounds a beep code. Which of the following describes the MOST likely cause of this error?

Either no memory is installed or the memory was not detected. If the system boot fails and sounds a beep code, the most likely cause is that either no memory is installed or the memory was not detected. If a card or memory module is not seated properly or the system includes unsupported memory, the system will boot, but the display will remain blank. If POST fails to recognize all of the memory, the system will boot, but the memory count will be incorrect.

Which type of software-generated problems can indicate that a software bug is causing a memory error? (Select THREE.)

Exception error General-protection fault Page fault Software-generated memory problems include the following: Exception error General-protection fault Page fault Registry errors indicate that parts of the registry are written to faulty sections of RAM. Parity interrupt usually indicates a failing module or discrepancies between new and old memory. An incorrect memory count can happen with incompatible memory installation; remember to avoid combining dual-bank memory with single-bank memory.

You have installed a new computer with a quad-core 64-bit processor, 6 GB of memory, and a PCIe video card with 512 MB of memory. After installing the operating system, you see less than 4 GB of memory showing as available in Windows. Which of the following actions would MOST likely rectify this issue?

Install a 64-bit version of the operating system. In this scenario, the most likely cause is the operating system being a 32-bit operating system. You must use a 64-bit operating system to use memory above 4 GB. The AGP aperture is a method for sharing system memory with an AGP video card instead of PCIe. With shared memory, some of the memory is used by the video card and is not available for the system. You do not update memory controller drivers.

After installing two memory modules, you power on the system to check for errors. You find that the BIOS program recognizes only one of the memory modules. While troubleshooting this issue, which of the following is BEST to try first?

Make sure that both modules are seated properly in their slots. In this case, you should check to ensure that you installed the memory correctly. Most BIOS programs include a memory count that displays the total amount of system memory. If it does not count the proper amount of memory, begin by checking to make sure the memory is inserted correctly. After the memory is installed correctly, if it is still not recognized, try removing one module to identify which module has the problem. Move the modules to different motherboard slots to see if you can get the system to detect the memory. In most cases, you will not need to change the memory timings. When you do, it is typically because the system is unstable or crashes. Testing memory helps you identify when specific memory storage locations are going bad. Device Manager will not enable memory the BIOS does not recognize.

You have just built a new system from scratch. You turn the computer on, but the system boot fails and sounds a beep code. Which of the following is the MOST likely cause?

Memory not installed or not detected If memory was not installed in the new computer or was not detected during boot up, the system boot will fail, and a beep code sound will be heard. If unsupported memory was installed, the system will boot, but the display will be blank. If incompatible memory was installed, such as combining dual-bank with single-bank memory, the system will boot, but the memory count will be incorrect. If a mix of new and old memory was used, the system will boot, but will display a memory error message.

You are in the process of configuring a new computer. The motherboard has four memory slots and supports dual-channel memory. You install two memory modules. When you boot the computer, the BIOS recognizes both modules, but the memory is not configured to run in dual-channel mode. What should you do?

Move the modules to the correct motherboard slots. To use dual-channel memory, you will need to install memory in the correct slots. Depending on the motherboard, the two slots might be next to each other or alternating. Consult the motherboard documentation for the correct configuration. Dual-channel support is mainly a function of the motherboard, not the memory itself. Continuity modules are used with Rambus RAM; if continuity modules were required on this system, none of the memory would have been detected. The CAS latency is used for memory timing. You might modify the timing if the system is unstable at the current memory timing settings.

There are critical times when memory problems often manifest themselves. Match each critical time on the left with the corresponding cause of the memory problems on the right.

This event can require more memory and can cause problems if there is not enough memory when it occurs. - Software installation Memory is not properly seated or missing/the motherboard is defective. - First boot of a new computer Incompletely or improperly doing this can cause errors that appear to be memory-related. - Hardware installation or removal The memory is not compatible and was not installed and configured properly. - Memory upgrade At these critical times, memory problems can manifest themselves as follows: First boot of a new computer - memory is not properly seated, missing, or the motherboard is defective. After a memory upgrade - ensure that the memory is compatible and was installed and configured properly. After software installation - new software can require more memory and can cause problems if there is not enough memory for the software. After hardware installation or removal - incompletely or improperly installed hardware can cause errors that appear to be memory-related.


Kaugnay na mga set ng pag-aaral

ATI Health Assess 2.0: Breast and Lymphatics

View Set

Big Ten: Bully Pulpit (President)

View Set

Mergers and Acquisitions Chapter 0

View Set

Myelination and white and gray matter.

View Set

BIO 106 - Chapter 6 HW MAP - Exam 2

View Set

Unit 3 Section 1 Cellular Replication

View Set

Ch. 10 Psychology 101 (Launchpad)

View Set