Chapter 10 Wireless Networking

what purpose does a wireless site survey fulfill? choose two

1. to identify the coverage are and preffered placement of access points 2. to identify existing or potential sources of inference

How many total channels are available for 802.11g wireless networks? 3 11 12 23 54

11

Which data transmission rate is defined by the IEEE 802.11b wireless standard? 2 Mbps 10 Mbps 11 Mbps 56 Mbps

11 Mbps

Which technologies are used by the 802.11ac standard to increase network bandwidth? (Select two.) 40 MHz bonded channels 160 MHz bonded channels Four MIMO radio streams Data compression Eight MIMO radio streams

160 MHz bonded channels Eight MIMO radio streams

Which of the following are frequencies defined by 802.11 committees for wireless networking? (Select two.) 900 MHz 1.9 GHz 2.4 GHz 5.75 GHz 10 GHz

2.4 GHz 5.75 GHz

How many total channels are available for 802.11a wireless networks? 3 11 12 23 54

23

What is the frequency of 802.11a networking? 900 MHz 1.2 GHz 2.4 GHz 5.75 GHz

5.75 GHz

You are designing a wireless network for a client. Your client needs the network to support a data rate of at least 54 Mbps. In addition, the client already has a wireless telephone system installed that operates 2.4 GHz. Which 802.11 standard will work best in this situation? 802.11g 802.11d 802.11a 802.11b 802.11c

802.11a

Which IEEE wireless standards specify transmission speeds up to 54 Mbps? (Select two.) 802.1x Bluetooth 802.11a 802.11g 802.11b

802.11a 802.11g

you are designing a wireless network for a client. Your client the network to support a data of at least 54 Mbps. In addition, the client already has a wireless telephone system installed that operates at 2.4 GHz.

802.11a 802.11n

Which IEEE standard describes wireless communication? 802.2 802.11b 802.3 802.5 802.7b

802.11b

After installing a new 2.4Ghz cordless phone system in your office, you notice that wireless network performance is adversely affected. Which of the following wireless networking standards are you most likely using? (Select two.) 802.11g 802.11a Bluetooth 802.11b

802.11g 802.11b

You are designing an update to your client's wireless network. The existing wireless network uses 802.11b equipment; which your client complains runs too slowly. She wants to upgrade the network to run up to 600 Mbps. Due to budget constraints, your client wants to upgrade only the wireless access points in the network this year. Next year, she will upgrade the wireless network boards in her users' workstations. She has also indicated that the system must continue to function during the transition period. Which 802.11 standard will work best in this situation? 802.11c 802.11d 802.11a 802.11b 802.11n

802.11n

You are designing an update to your client's wireless network. the Existing wireless network uses 802.11g equipment, which your client complains runs too slowly. She wants to upgrade the network to run at 150 Mbps or faster. due to budget constraints, your client wants to upgrade only the wireless access points in the network this year. Next Year, she will upgrade the wireless NICs in the workstations. She has also indicated that the system must continue to function during the transition period. which 802.11 standard will work best in this situation?

802.11n

You have been contacted by OsCorp to recommend a wireless Internet solution. The wireless strategy must support a transmission range of 1,200 feet, use a frequency range of 5 GHz, and provide the highest possible transmission speeds. Which of the following wireless solutions would you recommend? 802.11n Bluetooth WEP 802.11b 802.11a

802.11n

you are designing a wireless network for a client. Your client needs the network to support a data of at least 150 Mbps. In addition, the client already has a wireless telephone system installed that operates 2.4 GHz.

802.11n

You have decided to conduct a business meeting at a local coffee shop. The coffee shop you chose has a wireless hotspot for customers who want internet access. You decide to check your email before the meeting begins. When you open the browser, you cannot gain internet access. Other customers are using the internet without problems. You are sure your laptops wireless adapter works because you use a wireless connection at work. What is the likely cause of the problem? Different LAN protocols are being used. WAP is out of range. Antenna strength on the WAP is too low. A mismatched SSID. PPP is not configured correctly.

A mismatched SSID.

You are designing a wireless network implementation for a small business. The business deals with sensitive customer information, so data emanation must be reduced as much as possible. The floor plan of the office is shown below. Match each type of access point antenna on the left with the appropriate location on the floor plan on the right. Each antenna type can be used once, more than once, or not at all.

A. Directional B. Directional C. Omni-Directional D. Directional E. Directional F. Directional G. Directional

Your consulting firm has been hired by a small business to implement a wireless network. The company leases two office suites within a business park approximately 200m apart, as shown below. The objectives of the implementation are as follows: • Create a secure wireless network that doesn't emanate beyond each office space by implementing access points in locations A-D in each building. • Connect the wireless networks at each office together with a secure outdoor wireless link using locations E and F. Drag the antenna type from the list on the left to the appropriate location on the right. Each antenna type can be used more than once or not at all.

A. Normal gain directional antenna aimed east B. Normal gain directional antenna aimed south C. Normal gain directional antenna aimed north D. Normal gain directional antenna aimed west E. High-gain directional antenna aimed east F. High-gain directional antenna aimed west

You need to configure a wireless network. You want to use WPA2 Enterprise. Which of the following components will be part of your design? (Select two.) Open authentication WEP encryption TKIP encryption Preshared keys AES encryption 802.1x

AES encryption 802.1x

You are troubleshooting a wireless connectivity issue in a small office. You determine that the 2.4GHz cordless phones used in the office are interfering with the wireless network transmissions. If the cordless phones are causing the interference, which of the following wireless standards could the network be using? (Select two.) Bluetooth 802.11b 802.3a 802.11a Infrared

Bluetooth 802.11b

All of the 802.11 standards for wireless networking support which type of communication path sharing technology?

CSMA/CA

match each wireless term or concept on the left with its associated description on the right. Each term may be used more than once; not all descriptions have a matching term.

Compares the level of the Wi-Fi signal to the level of background radio signals: signal to noise ration Checks channel utilization and identifies sources of RF inference: spectrum analysis identifies how strong a radio signal as at the receiver: Relieve signal level Identifies the number of useful bits delivered from the sender to the receiver Leave blank causes multiple copies of the same radio signal to be received by the receiving antenna: bounce degrades wireless network performance: device saturation

You have configured a wireless access point to create a small network. For security, you have disabled SSID broadcast. From a client computer, you try to browse to find the access point. You see some other wireless networks in the area, but cannot see your network. What should you do? Enable the wireless card on the client. Configure a profile on the wireless client. Set the channel on the client to match the channel used by the access point. Decrease the beacon interval on the access point.

Configure a profile on the wireless client.

You are the wireless network administrator for your organization. As the size of the organization has grown, you've decided to upgrade your wireless network to use 802.1x authentication instead of using preshared keys. To do this, you need to configure a radius server and radius clients. You want the server and the clients to mutually authenticate with each other. What should you do? (Select two. Each response is a part of the complete solution.) Configure all wireless workstations with client certificates. Configure all RADIUS clients with a preshared key. Configure the RADIUS server with a server certificate. Configure the RADIUS server with a preshared key. Configure all wireless access points with client certificates.

Configure the RADIUS server with a server certificate. Configure all wireless access points with client certificates.

which wireless networking is used to connect multiple APs together?

DS

You have configured a wireless access point to create a small network. You have configured all necessary parameters. Wireless clients seem to take a long time to find the wireless access point. You want to reduce the time it takes for the clients to connect. What should you do? Decrease the beacon interval. Change the channel on the access point to a lower number. Enable SSID broadcast. Create a wireless profile on the client.

Decrease the beacon interval.

Which of the following measures will make your wireless network invisible to the casual attacker performing war driving? Change the default SSID Disable SSID broadcast Implement WPA2 Personal Use a form of authentication other than open authentication

Disable SSID broadcast

Which of the following enterprise wireless deployment models uses access points with enough intelligence to allow for the creation of quest WLANs for keeping public wireless traffic separated from private traffic?

Distributed wireless mesh infrastructure

your wireless network consists of multiple 802.11n access points that are configures as follows: -SSID (hidden): Corpnet -security: WPA2-PSK using AES -Frequency: 5.7 GHz -Bandwidth per channel: 20 MHz

Double the bandwidth assigned per channel to 40 MHz.

Which of the following features are supplied by WPA2 on a wireless network? A centralized access point for clients Traffic filtering based on packet characteristics Encryption Network identification Client connection refusals based on MAC address

Encryption

which of the ff is true of a wireless network SSID?

Groups wireless devices together into the same logical network.

You need to implement a wireless network link between two buildings on a college campus. A wired network has already been implemented within each building. The buildings are 100 meters apart. What type of wireless antennae should you use on each side of the link? (Select two.) Bridge High-gain Directional Omni-directional Normal-gain

High-gain Directional

An access point that conforms to the IEEE 802.11b standard behaves similarly to what other networking device?

Hub

Which of the following protocols or mechanisms is used to provide security on a wireless network? (Select three.) IPsec RDP 802.1x WPA

IPsec 802.1x WPA

Your wireless network consists of multiple 802.11n access points that are configured as follows: • SSID (hidden): CorpNet • Security: WPA2-PSK using AES • Frequency: 5.75 GHz • Bandwidth per channel: 40 MHz Because of the unique construction of your organization's facility, there are many locations that do not have a clear line of sight between network clients and access points. As a result, radio signals are reflected along multiple paths before finally being received. The result is distorted signals that interfere with each other. What should you do? Implement antenna diversity. Reduce the power of the access point radio signals. Install directional access points. Switch to RADIUS authentication for wireless clients.

Implement antenna diversity.

Match each type of access point on the left with the wireless network architecture that they are commonly used in on the right

Independent access point infrastructure Intelligent AP Hub-and-spoke infrastructure Lightweight AP Distributed wireless mesh infrastructure Intelligent AP

Match each wireless device on the left with is corresponding characteristics on the right.

Manages all of the Apps that are connected to it Wireless controller Suppors 30 to 50 wireless clients per access point Wireless controller Profides NAT routing and an ethernet switch in one device SOHO wireless router Supports a maximum of 5-10 wireless clients SOHO wireless router Pushes wireless configurations settings to connected access points Wireless controller

Match the wireless networking term or concept on the left with its appropriate description on the right.

Moving an wireless device between access points within the same wireless network Roaming Used by Cisco wireless equipment to route frames back and forth between the wireless network and the wired LAN LWAPP Specifies the number of clients that utilize a wireless network Device density Automatically partitions a single broadcast domain into multiple VLANs VLAN pooling Graphically displays wireless signal strength within an area Heat map Connects two wired networks over a Wi-Fi network Wireless bridge Identifies relative strength of a radio signal at the receiver Heat map The number of useful bits delivered from sender to receiver within a specified amount of time Goodput

What is the least secure place to locate an access point with an omni-directional antenna when creating a wireless cell? In the center of the building In common or community work areas Near a window Above the 3rd floor

Near a window

You are an administrator of a growing network. You notice the network you have created is broadcasting, but you cannot ping systems on different segments of your network. What device should you use to fix this issue? Access point Network hub Range extender Network bridge

Network bridge

You are setting up a wireless hotspot in a local coffee shop. For best results, you want to disperse the radio signals evenly throughout the coffee shop. Which of the following antenna types would you use on the AP to provide a 360-degree dispersed wave pattern? Multi-point Multi-directional Omni-directional Uni-directional Directional

Omni-directional

You want to implement 802.1x authentication on your wireless network. Where would you configure passwords that are used for authentication? On a certificate authority (CA) On the wireless access point On the wireless access point and each wireless device On a RADIUS server

On a RADIUS server

You need to place a wireless access point in your two-story building. While trying avoid interference, which of the following is the best location for the access point? On the top floor In the kitchen area Near the backup generators In the basement

On the top floor

You have been hired to troubleshoot a wireless connectivity issue for two separate networks located within a close proximity. Both networks use a WAP from the same manufacturer, and all settings, with the exception of SSIDs, remain configured to the default. Which of the following might you suspect as the cause of the connectivity problems? The SSIDs of the two server systems match. WEP overlap. Crosstalk between the RF signals. Overlapping channels. The SSIDs of the two client systems match.

Overlapping channels.

An attacker is trying to compromise a wireless network that has been secured using WPA2-PSK and AES. She first tried using AirSnort to capture packets, but found that she couldn't break the encryption. As an alternative, she used software to configure her laptop to function as an access point. She configured the fake access point with the same SSID as the wireless network she is trying to break into. When wireless clients connect to her access point, she presents them with a web page asking them to enter the WPA2 passphrase. When they do, she then uses it to connect a wireless client to the real access point. Which attack techniques did the attacker use in this scenario? (Select two.) Man-in-the-middle Smurf Pharming Evil twin Denial of service

Pharming Evil twin

Which of the following recommendations should you follow when placing access points to provide wireless access for users within your company building? Place access points above where most clients are. Place multiple access points in the same area. Place access points near outside walls. Place access points in the basement.

Place access points above where most clients are.

You want to connect your client computer to a wireless access point that is connected to your wired network at work. The network administrator tells you that the access point is configured to use WPA2 Personal with the strongest encryption method possible. SSID broadcast is turned off. Which of the following must you configure manually on the client? (Select three.) TKIP Preshared key SSID Channel Username and password AES

Preshared key SSID AES

You are implementing a wireless network inside a local office. You require a wireless link to connect a laptop in the administrator's office directly to a system in the sales department. In the default configuration, the wireless AP uses a 360-dispersed RF wave design. After installation, the signal between the two systems is weak, as many obstacles interfere with the signal. Which of the following strategies could you try to increase signal strength? Replace the directional antenna with an omni-directional antenna. Increase the RF setting on the AP. Increase the RF setting on the client system. Replace the omni-directional antenna with a directional antenna. Increase the RF power on the isotropic antenna.

Replace the omni-directional antenna with a directional antenna.

Your company security policy states that wireless networks are not to be used because of the potential security risk they present to your network. One day you find that an employee has connected a wireless access point to the network in his office. What type of security risk is this? Rogue access point Man-in-the-middle Phishing Social engineering Physical security

Rogue access point

You have physically added a wireless access point to your network and installed a wireless networking card in two laptops running Windows. Neither laptop can find the network, and you have come to the conclusion that you must manually configure the wireless access point (AP). Which of the following values uniquely identifies the network AP? SSID Channel PS WEP

SSID

You are configuring a wireless network with two wireless access points. Both access points connect to the same wired network. You want wireless users to be able to connect to either access point and have the ability to roam between the two access points. How should you configure the access points? Different SSID, different channel Same SSID, different channel Different SSID, same channel Same SSID, same channel

Same SSID, different channel

Recently, a catastrophic early morning power surge occurred. It was followed by an outage that lasted longer than your backup equipment could supply temporary power. After you powered the equipment back on, everything initially appeared to work correctly. However, ever since this event, some mobile users report that wireless network connections sometimes get dropped or perform very poorly. What should you do? (Select two.) Configure each access point to use 802.1x authentication. Configure each access point to use a different SSID. Set access point B to use 802.11n wireless networking. Set the channel used by access point B to 11. Set the channel used by access point B to 8. Set access points A and C to use 802.11b wireless networking. Set the channel used by access point A to 5. Set the channel used by access point C to 7.

Set access point B to use 802.11n wireless networking. Set the channel used by access point B to 11.

You have a small wireless network that uses multiple access points. The network uses WPA and broadcasts the SSID. WPA2 is not supported by the wireless access points. You want to connect a laptop computer to the wireless network. Which of the following parameters will you need to configure on the laptop? (Select two.) AES encryption TKIP encryption Channel BSSID Preshared key

TKIP encryption Preshared key

A user on your network has been moved to another office down the hall. After the move, she calls you complaining that she has only occasional network access through her wireless connection. Which of the following is most likely the cause of the problem? The client has incorrect WEP settings. An SSID mismatch between the client and the WAP. An SSID mismatch between the client and the server. The client system has moved too far away from the access point. The encryption level has been erroneously set back to the default setting.

The client system has moved too far away from the access point.

A user calls to report that she is experiencing intermittent problems while accessing the wireless network from her laptop computer. While talking to her, you discover that she is trying to work from the coffee room two floors above the floor where she normally works. What is the most likely cause of her connectivity problem? The user needs a new IP address because she is working on a different floor. The user has not yet rebooted her laptop computer while at her new location. The user has not yet logged off and back on to the network while at her new location. The wireless network access point on the user's normal floor has failed. The user is out of the effective range of the wireless access point on her floor.

The user is out of the effective range of the wireless access point on her floor.

Your organization uses an 802.11b wireless network. Recently, other tenants installed the following equipment in your building: • A wireless television distribution system running at 2.4 GHz • A wireless phone system running at 5.8 GHz • A wireless phone system running at 900 MHz • An 802.11a wireless network running in the 5.725 - 5.850 GHz frequency range • An 802.11j wireless network running in the 4.9 - 5.0 GHz frequency range Since this equipment was installed, your wireless network has been experiencing significant interference. Which system is to blame? The 5.8 GHz wireless phone system The 900 MHz wireless phone system The wireless TV system The 802.11a wireless network The 802.11j wireless network

The wireless TV system

While configuring a new 802.11g wireless network, you discover another wireless network within range that uses the same channel ID that you intend to use. Which of the following strategies are you most likely to adopt in order to avoid a conflict between the networks? Use 802.11b instead of 802.11g. Use the same channel ID, but configure your wireless network to use WEP. Use a different channel ID. Use the same channel ID, but configure a different SSID.

Use a different channel ID.

match the wireless signaling method on the left with its definition on the right.

Uses a narrow frequency band and hops data signals in a predictable sequence: FHSS Breaks data into pieces and sends the pieces across multiple frequencies in a defined range: DSSS breaks data into very small data streams in order to send the information across long distances: OFDM

Which of the following wireless security methods uses a common shared key configured on the wireless access point and all wireless clients? WPA Personal and WPA2 Enterprise WPA Enterprise and WPA2 Enterprise WEP, WPA Personal, and WPA2 Personal WEP, WPA Personal, WPA Enterprise, WPA2 Personal, and WPA2 Enterprise

WEP, WPA Personal, and WPA2 Personal

Which of the following provides security for wireless networks? CSMA/CD 802.11a WPA WAP 802.3u

Wi-Fi protected access (WPA).

which protocol is well known for its use in the home security and home automation industry, uses a mesh topology, makes devices act as repeaters, and has a low data transfer rate?

Z-Wave

you are building a wireless network within and between two buildings. the buildings re separated by more than 300 feet, The wireless network should meet the following requirements: -wireless data with in building 1 should be protected with the highest degree of security. -wireless data within building 2 should be accessible and permitted by any wireless client. -wireless signals between buildings 1 and 2 should be protected with the highest degrees of security. -wireless signals within buildings 1 and 2 should cover the whole structure, but not extended to the outside. for each location on the image below, you need to select the ff: -antenna option -security option

building 1 - Location A: 1.Right - facing directional antenna. 2. WPA2 with CCMP Building 1 - Location B: 1.WPA2 with CCMP 2. Omni-directional antenna. Building 1 - Location C 1. Left- facing directional antenna 2. WPA2 with CCMP Building 1 - Location D 1. WPA2 with CCMP 2. right facing high again directional antenna. Building 2 - Location A 1. Omni-directional antenna 2. WEP with open authentication Building 2 -mLocation B 1. left-facing high-gain directional antenna 2. WPA2 with CCMP

to optimize your network, you want to configure your wireless AP to use a channel that meets the following criteria: -Non-overlapping -low utilization -low interference yo performed a spectrum analysis to identify 2.4 GHz wireless channel utilization, as shown in the exhibit. (To read the spectrum analysis, imagine a line coming down from the center of the highest point of each wave. For example, the four whose crest are over channel 11 belong to channel 11.) based on the result, which channel you configure your wireless AP to use?

channel 1

you have been hired to design a wireless network for a SOHO environment. You are currently in the process of gathering network requirements from management. which of the ff. questions should you ask? select three

is the size of the business expected to grow in the future? how many devices will need to be supported? what type data will be transmitted on the network?

what is the risk associated with smart technology used in networked devices such as smart refrigerators, environmental controls, or industrial equipment?

they are vulnerable to exploits due to weaker security