Chapter 8 Exam

Which address does a DHCPv4 server target when sending a DHCPOFFER message to a client that makes an address request? client hardware address client IP address broadcast MAC address gateway IP address

client hardware address

Match the descriptions to the corresponding DHCPv6 server type. Stateless DHCPv6

clients send only DHCPv6 INFORMATION-REQUEST messages to the server enabled in RA messages with the ipv6 nd other-config-flag command enabled on the client with the ipv6 address autoconfig command

Which DHCPv4 message will a client send to accept an IPv4 address that is offered by a DHCP server? broadcast DHCPACK unicast DHCPREQUEST unicast DHCPACK broadcast DHCPREQUEST

broadcast DHCPREQUEST

An administrator wants to configure hosts to automatically assign IPv6 addresses to themselves by the use of Router Advertisement messages, but also to obtain the DNS server address from a DHCPv6 server. Which address assignment method should be configured? stateless DHCPv6 stateful DHCPv6 RA and EUI-64 SLAAC

stateless DHCPv6

Refer to the exhibit. What should be done to allow PC-A to receive an IPv6 address from the DHCPv6 server? Configure the ipv6 nd managed-config-flag command on interface Fa0/1. Change the ipv6 nd managed-config-flag command to ipv6 nd other-config-flag . Add the IPv6 address 2001:DB8:1234:5678::10/64 to the interface configuration of the DHCPv6 server. Add the ipv6 dhcp relay command to interface Fa0/0.

Add the ipv6 dhcp relay command to interface Fa0/0.

Order the steps of configuring a router as a DHCPv4 server. (Not all options are used.) Step 2

Configure a DHCP pool.

As a DHCPv4 client lease is about to expire, what is the message that the client sends the DHCP server? DHCPOFFER DHCPREQUEST DHCPDISCOVER DHCPACK

DHCPREQUEST

A company implements the stateless DHCPv6 method for configuring IPv6 addresses on employee workstations. After a workstation receives messages from multiple DHCPv6 servers to indicate their availability for DHCPv6 service, which message does it send to a server for configuration information? DHCPv6 INFORMATION-REQUEST DHCPv6 ADVERTISE DHCPv6 REQUEST DHCPv6 SOLICIT

DHCPv6 INFORMATION-REQUEST

Order the steps of configuring a router as a DHCPv4 server. (Not all options are used.) Step 3

Define the default gateway router.

What two methods can be used to generate an interface ID by an IPv6 host that is using SLAAC? (Choose two.) stateful DHCPv6 DAD ARP EUI-64 random generation

EUI-64 random generation

Order the steps of configuring a router as a DHCPv4 server. (Not all options are used.) Step 1

Exclude IP address.

A company uses DHCP servers to dynamically assign IPv4 addresses to employee workstations. The address lease duration is set as 5 days. An employee returns to the office after an absence of one week. When the employee boots the workstation, it sends a message to obtain an IP address. Which Layer 2 and Layer 3 destination addresses will the message contain? both MAC and IPv4 addresses of the DHCP server FF-FF-FF-FF-FF-FF and 255.255.255.255 FF-FF-FF-FF-FF-FF and IPv4 address of the DHCP server MAC address of the DHCP server and 255.255.255.255

FF-FF-FF-FF-FF-FF and 255.255.255.255

What is an advantage of configuring a Cisco router as a relay agent? It reduces the response time from a DHCP server. It can provide relay services for multiple UDP services. It can forward both broadcast and multicast messages on behalf of clients. It will allow DHCPDISCOVER messages to pass without alteration.

It can provide relay services for multiple UDP services.

How does an IPv6 client ensure that it has a unique address after it configures its IPv6 address using the SLAAC allocation method? It sends an ICMPv6 Neighbor Solicitation message with the IPv6 address as the target IPv6 address. It checks with the IPv6 address database that is hosted by the SLAAC server. It sends an ARP message with the IPv6 address as the destination IPv6 address. It contacts the DHCPv6 server via a special formed ICMPv6 message.

It sends an ICMPv6 Neighbor Solicitation message with the IPv6 address as the target IPv6 address.

A network administrator configures a router to send RA messages with M flag as 0 and O flag as 1. Which statement describes the effect of this configuration when a PC tries to configure its IPv6 address? It should contact a DHCPv6 server for all the information that it needs. It should use the information that is contained in the RA message and contact a DHCPv6 server for additional information. It should contact a DHCPv6 server for the prefix, the prefix-length information, and an interface ID that is both random and unique. It should use the information that is contained in the RA message exclusively.

It should use the information that is contained in the RA message and contact a DHCPv6 server for additional information.

What is the result of a network technician issuing the command ip dhcp excluded-address 10.0.15.1 10.0.15.15 on a Cisco router? The Cisco router will allow only the specified IP addresses to be leased to clients. The Cisco router will exclude only the 10.0.15.1 and 10.0.15.15 IP addresses from being leased to DHCP clients. The Cisco router will automatically create a DHCP pool using a /28 mask. The Cisco router will exclude 15 IP addresses from being leased to DHCP clients.

The Cisco router will exclude 15 IP addresses from being leased to DHCP clients.

Refer to the exhibit. A network administrator is implementing the stateless DHCPv6 operation for the company. Clients are configuring IPv6 addresses as expected. However, the clients are not getting the DNS server address and the domain name information configured in the DHCP pool. What could be the cause of the problem? The GigabitEthernet interface is not activated. The clients cannot communicate with the DHCPv6 server, evidenced by the number of active clients being 0. The router is configured for SLAAC operation. The DNS server address is not on the same network as the clients are on.

The router is configured for SLAAC operation.

Refer to the exhibit. A network administrator is implementing stateful DHCPv6 operation for the company. However, the clients are not using the prefix and prefix-length information that is configured in the DHCP pool. The administrator issues a show ipv6 interface command. What could be the cause of the problem? The router is configured for stateless DHCPv6 operation. No virtual link-local address is configured. The router is configured for SLAAC DHCPv6 operation. The Duplicate Address Detection feature is disabled.

The router is configured for stateless DHCPv6 operation.

Under which two circumstances would a router usually be configured as a DHCPv4 client? (Choose two.) The administrator needs the router to act as a relay agent. The router has a fixed IP address. The router is meant to provide IP addresses to the hosts. This is an ISP requirement. The router is intended to be used as a SOHO gateway.

This is an ISP requirement. The router is intended to be used as a SOHO gateway.

An administrator issues the commands: Router(config)# interface g0/1 Router(config-if)# ip address dhcp What is the administrator trying to achieve? configuring the router to act as a DHCPv4 server configuring the router to resolve IP address conflicts configuring the router to act as a relay agent configuring the router to obtain IP parameters from a DHCPv4 server

configuring the router to obtain IP parameters from a DHCPv4 server

Which is a DHCPv4 address allocation method that assigns IPv4 addresses for a limited lease period? automatic allocation dynamic allocation pre-allocation manual allocation

dynamic allocation

Refer to the exhibit. Based on the output that is shown, what kind of IPv6 addressing is being configured? stateless DHCPv6 static link-local stateful DHCPv6 SLAAC

stateless DHCPv6

What is used in the EUI-64 process to create an IPv6 interface ID on an IPv6 enabled interface? an IPv4 address that is configured on the interface a randomly generated 64-bit hexadecimal address the MAC address of the IPv6 enabled interface an IPv6 address that is provided by a DHCPv6 server

the MAC address of the IPv6 enabled interface

A company uses the SLAAC method to configure IPv6 addresses for the employee workstations. Which address will a client use as its default gateway?​ the all-routers multicast address the link-local address of the router interface that is attached to the network the global unicast address of the router interface that is attached to the network the unique local address of the router interface that is attached to the network

the link-local address of the router interface that is attached to the network

Match the descriptions to the corresponding DHCPv6 server type. Stateful DHCPv6

uses the address command to create a pool of addresses for clients enabled on the client with the ipv6 address dhcp command the M flag is set to 1 in RA messages