CompTIA A+ 220-801 Test version 7

Pataasin ang iyong marka sa homework at exams ngayon gamit ang Quizwiz!

On an ATX motherboard, the 4-pin auxiliary power connector provides which of the following? A. Additional power to onboard devices B. Additional power to PCIx peripheral cards C. Additional power to the South Bridge D. Additional power to the CPU voltage regulator

Answer: D Reference:http://pcsupport.about.com/od/insidethepc/a/atx-pinout-4-pin-12v-psu.htm

Which of the following technologies is responsible for communication with the CPU? A. eSATA B. PCI express C. Southbridge D. Northbridge

Answer: D Reference:http://www.computerhope.com/jargon/n/northbri.htm the northbridge is an integrated circuit responsible for communications between the CPU interface, AGP, and the memory. Unlike the Southbridge the Northbridge is directly connected to these components and acts like a "bridge" for the Southbridge chip to communicate with the CPU, RAM, and graphics controller. Today, the northbridge is a single-chip that is North of the PCI bus, however, early computers may have had up to three separate chips that made up the northbridge.

Which of the following connector types uses a single RCA style connector? A. DVI B. VGA C. RGB D. Composite video

Answer: D Reference:http://www.crutchfield.com/SzwZUk3RXHNR/learn/learningcenter/home/connections_glossary.html(see composite video jack)

USB 2.0 and which of the following ports share the same connector? A. Micro USB 2.0 B. Mini USB 2.0 C. Micro USB 3.0 D. USB 3.0

Answer: D Reference:http://www.diffen.com/difference/USB_2.0_vs_USB_3.0

Which of the following is the MAXIMUM transfer speed of USB 2.0? A. 100 Mbps B. 400 Mbps C. 420 Mbps D. 480 Mbps

Answer: D Reference:http://www.lyberty.com/tech/terms/usb.html

A technician wants to install a secondary IDE drive which will be configured for additional user storage on the same IDE channel of the drive with the operating system. Which of the following jumper configurations should the technician use for the additional drive, if the drive with the operating system is set to MA? A. Place a jumper on both the MA and CS jumper block of the secondary drive. B. Place a jumper on the MA jumper block of the secondary drive. C. Place a jumper on both the SL and CS jumper block of the secondary drive. D. Place a jumper on the SL jumper block of the secondary drive.

Answer: D Reference:http://www.pcguide.com/ref/hdd/if/ide/confJumpering-c.html

Which of the following requires a MINIMUM of four hard drives? A. RAID 0 B. RAID 1 C. RAID 5 D. RAID 10

Answer: D Reference:http://www.pcworld.com/article/132877/RAID.html(see RAID 1+0, 0+1, 10)

When installing multiple SCSI drives in a system, which of the following is correct? A. All drives must have the same SCSI ID. B. Drives will be automatically assigned an ID by the controller. C. Drives in the same RAID array must have the same SCSI ID. D. Each drive must have a different SCSI ID.

Answer: D Reference:http://www.textfiles.com/computers/scsi.txt

A composite cable connects to which of the following connectors? A. HDMI B. S-video C. DVI D. RCA

Answer: D Reference:http://www.webopedia.com/TERM/R/RCA_cable.html

A technician is giving a safety class to new employees. Which of the following contains potentially dangerous voltages and should be handled with care, even if the power has been recently disconnected? A. Laser printer B. Wireless router C. Paper shredder D. CRT monitor

Answer: D Reference:http://www.wikihow.com/Discharge-a-CRT-Monitor

Which of the following devices transmits data to all ports regardless of final destination? A. Firewall B. Router C. Switch D. Hub

Answer: D. Hub (Reference:http://computernetworkingnotes.com/comptia-n-plus-study-guide/network-devices-hubswitch-router.html(see Hub)

Which of the following are the MOST important factors to address when a technician is choosing the components for a CAD workstation? (Select THREE). A. Large drive space allocation B. Powerful sound card C. Multiple network cards D. Multiple large HD monitors E. Powerful video card F. Maximum RAM G. Powerful processor

Answer: E,F,G Reference:http://www.webopedia.com/TERM/C/CAD.html

A technician is installing a new TV tuner on a Windows 7 HTPC and no channels are showing up. Which of the following is the MOST likely cause? A. The TV cable is connected to the FM/AM input. B. The TV tuner card does not support HD channels. C. The TV tuner card is not properly seated. D. The cable signal is too weak. Answer: A Explanation: One possible cause might be that the TV cable is connected to FM/AM input mistakenly. TV tuner cards have FM/AM input port which is similar to the TV cable input.

Answer: A Explanation: One possible cause might be that the TV cable is connected to FM/AM input mistakenly. TV tuner cards have FM/AM input port which is similar to the TV cable input.

An end user requires a computer to support computer aided drafting and computer aided modeling. Which of the following component packages should a technician recommend to the end user? A. Powerful processor, high-end graphics card, and maximum RAM B. File streaming, printer sharing, and a RAID array C. Surround sound audio, compact form factor, HDMI output D. Processor and RAM that meets minimum Windows requirements

Answer: A Explanation: Since AutoCAD and computer aided modeling requires more muscle to do the renderings, you need a powerful processor, lots of RAM and an expensive high end graphics card to support the software.

After installing a bar code reader, which of the following is commonly done to configure the reader? A. Scan in program codes B. Enable the code reader in the BIOS C. Use Device Manager to enable I/R ports D. Adjust jumper switches

Answer: A Explanation: To enable the bar code reader to function optimally, you need to scan in program codes so that it can identify the objects later on.

Joe, a customer, requests that the desktop system he is buying is able to be used at his vacation home in another country, as well as his regular home. The technician is aware that the country mentioned has different power requirements. Which of the following should the technician ensure the desktop contains? A. Dual voltage options B. UPS C. Inverter D. Micro-ATX connector

Answer: A Explanation: To make sure the computer doesn't get fried, install dual voltage options in a desktop so that it can cope with company's various power requirements.

A technician has 2GB of data that needs to be backed up from a customer's Windows 7 computer. Which of the following storage media should the technician use? A. DVD-RW B. CD-RW C. DVD-ROM D. CD-ROM

Answer: A Explanation: To store large amounts of data, you might need a DVD-RW because a DVD can hold a lot of GBs. CD-RW has limited space. Alternatively, you can now backup stuff on a USB stick as well.

After a technician installs a video card, which of the following should the technician configure NEXT? A. Resolution B. Colors C. Dots per inch D. Refresh rate

Answer: A Explanation: Video card is related to the resolution and color. To make sure the card is installed correctly and working properly, you need to check the resolution. If the desired resolution is not achieved, you can change the video card for a better one you can adjust the video card in the slot.

When a power supply does not meet minimum requirements for a motherboard, which of the following can happen? A. Computer will not POST B. Computer will overheat C. Monitor will not power on D. Processor will not run at proper speed

Answer: A Explanation: When the power is not supplied to the motherboard, the computer will not start because it needs electricity to run. Hence, the computer will not POST (power on self test)

Which of the following MUST be performed when installing a PCI sound card for use instead of the onboard sound? A. Install drivers B. Install additional memory C. Configure the jumpers D. Flash the BIOS

Answer: A Explanation: Whenever you want to use a PCI sound card that is not built into the motherboard, you need specific drivers to install it. Drivers are software that help the hardware to perform for a specific operating system.

Which of the following panel types would allow for the THINNEST possible display monitor? A. LED. B. CRT. C. DLP . D. Plasma.

Answer: A (Reference:http://electronics.howstuffworks.com/difference-between-lcd-and-led.htm)

Which of the following expansion cards would MOST likely require the use of an external power connector to function properly? A. PCI Express video card B. PCI Express fiber card C. PCI Express sound card D. PCI Express network card

Answer: A Reference:http://electronics.stackexchange.com/questions/49216/how-do-pci-express-graphicscards-pull-power-from-both-the-slot-and-the-external

Which of the following interfaces are used to simultaneously transfer video and audio at high rates? A. HDMI B. DVI-D C. S-Video D. DVI-I

Answer: A Reference:http://en.wikipedia.org/wiki/HDMI

The SODIMM memory form factor is generally used in which of the following? A. Laptops B. Servers C. Desktops D. Workstations Answer: A Reference:http://en.wikipedia.org/wiki/SO-DIMM

Answer: A Reference:http://en.wikipedia.org/wiki/SO-DIMM

Which of the following locations stores the boot sequence for a desktop computer? A. BIOS B. TPM C. CPU D. Boot sector Answer: A Reference:http://pcsupport.about.com/od/termsb/p/bios.htm

Answer: A Reference:http://pcsupport.about.com/od/termsb/p/bios.htm

Which of the following types of device cable types are used to connect output devices such as printers and scanners? A. Parallel B. eSATA C. IDE D. PATA

Answer: A Reference:http://wiki.answers.com/Q/What_is_a_parallel_connector

To configure two drives for MAXIMUM performance, which of the following RAID types should be used? A. RAID 0 B. RAID 1 C. RAID 5 D. RAID 10

Answer: A Reference:http://www.adaptec.com/nr/rdonlyres/874d145e-f64f-4804-9e27037bc5a9dce0/0/3994_raid_whichone_v112.pdf

Joe, a user, has installed a new monitor on an existing system. Joe calls a support technician and reports that everything on the new display is fuzzy. Which of the following describes what needs to be changed to correct this issue? A. The display resolution needs to match the native resolution. B. The old graphics card does not support the new monitor. C. The new monitor cable needs to have aluminum cores installed. D. The new monitor requires updated drivers to be installed.

Answer: A Reference:http://www.chrislongley.com/monitor.htm

A company is converting to LCD monitors and needs to properly dispose of all CRT monitors. Which of the following is an important consideration when disposing of CRT monitors? A. The materials within the cathode ray tube are harmful. B. They are heavier than LCD monitors and therefore require special disposal. C. The glass of the tube can easily break and cause serious injury. D. The rays of the cathode can cause blindness if someone is exposed.

Answer: A Reference:http://www.ecy.wa.gov/programs/hwtr/dangermat/electronic_waste_index.html

A threaded coaxial connector used to connect to a TV tuner is MOST often referred to as which of the following? A. F-connector B. RJ-11 connector C. IEEE 1394 connector D. RJ-45 connector

Answer: A Reference:http://www.ramelectronics.net/howto-av.aspx(see Television (TV/HDTV) connections

Ann, a customer, requests a high-capacity, cost effective backup media that she can administer and store offsite with no assistance. Which of the following media types would BEST meet Ann's request? A. Tape B. DVD C. Floppy D. SSD

Answer: A Reference:http://www.redwireservices.com/tape-backup-is-still-great

Which of the following should be used when building a high-end graphics workstation for CAD applications? (Select TWO). A. Main memory of 8 GB or more B. PCI-e video card with large amount of memory C. More than 4 accessible USB 2.0 ports D. A 32-bit OS to handle the large amount of expected disk I/O E. An eSATA external drive Answer: A,B Explanation: CAD applications need high memory and CPU resources to function optimally. Therefore, 8 GB main memory and a PCI-e video card with big memory is needed to render the drawings optimally.

Answer: A,B Explanation: CAD applications need high memory and CPU resources to function optimally. Therefore, 8 GB main memory and a PCI-e video card with big memory is needed to render the drawings optimally.

Which of the following represents a connector that supports the connection of external devices? (Select TWO). A. IEEE1394 B. eSATA C. EIDE D. SATA E. IDE

Answer: A,B Explanation: Both Firewire (IEEE 1394) and eSATA connectors can be used to connect external devices.

Which of the following expansion slots would support the HIGHEST transfer speeds for high-end graphics cards? (Select TWO). A. PCIe B. AGP 8x C. PCI D. ISA E. AGP

Answer: A,B Reference:http://www.srgclub.org/VideoCards-Monitors.html(See PCI Express)

A technician is tasked with selecting components to build a computer that will be used for computer-aided drafting and computer aided modeling. Which of the following components are the BEST choices? (Select TWO). A. Triple channel memory B. MIDI sound card C. Socket 1156 motherboard D. Onboard graphics E. Socket 1366 CPU

Answer: A,E A. Triple channel memory E. Socket 1366 CPU (Reference:http://www.tomshardware.com/forum/306223-28-socket-1155-1366 http://www.tomshardware.com/forum/292783-30-triple-channel-dual-channel)

A technician is dispatched to install additional RAM in a computer. The technician unplugs the system from the power source, and removes the cover of the PC. Which of the following should the technician do NEXT? A. Update the BIOS for compatibility. B. Put on an ESD strap. C. Use an anti-static bag to hold the RAM while installing. D. Clean out the PC with compressed air.

Answer: B Explanation: Before touching the innards of a computer like RAM, hard disk, CPU or any other component, you need to put an Electrostatic discharge strap so that the components do get static charge from you.

A client wants a technician to install more RAM on their graphics workstation. The client has provided a 4 GB SODIMM and had problems installing it. Which of the following is the probable reason for this? A. Graphic workstations require flash memory B. The memory is incompatible for the workstation C. Graphic workstations require solid state memory D. The workstation has no available memory slots

Answer: B Explanation: SO-DIMM memory is normally used in laptops and small form factor desktops. A graphics workstation is a fully configured PC. Therefore, a DIMM memory is needed to allow it to perform flawlessly.

When troubleshooting a PC that intermittently shuts off, which of the following should be monitored? A. Boot sequence B. CPU temperature C. SMART status D. TPM module

Answer: B Explanation: When the CPU temperature exceed the limit, the PC will shut off to wade off the heat and normalize the temperature otherwise the CPU will melt down.

Which of the following is the only place where initial boot settings can be configured? A. CMOS B. BIOS C. MBR D. HAL Answer: B Reference:http://buildyourowncomputerworkshop.com/firstboot.html

Answer: B Reference:http://buildyourowncomputerworkshop.com/firstboot.html

ECC memory offers which advantage over non-ECC memory? A. Less energy consumption B. The capability of error correction C. More efficient core communication D. Broader BUS throughput

Answer: B Reference:http://en.wikipedia.org/wiki/Error_detection_and_correction#Error-correcting_memory

Which of the following expansion slots is MOST commonly used for high-end video cards? A. PCI B. PCIe C. CNR D. AGP

Answer: B Reference:http://en.wikipedia.org/wiki/PCI_Express#External_PCIe_cards

Which of the following RAID types uses a drive mirroring algorithm? (Select TWO). A. RAID 0 B. RAID 1 C. RAID 5 D. RAID 6 E. RAID 10

Answer: B,E Reference:http://searchstorage.techtarget.com/definition/RAID RAID (redundant array of independent disks; originally redundant array of inexpensive disks) provides a way of storing the same data in different places (thus, redundantly) on multiple hard disks (though not all RAID levels provide redundancy). By placing data on multiple disks, input/output (I/O) operations can overlap in a balanced way, improving performance. Since multiple disks increase the mean time between failures (MTBF), storing data redundantly also increases fault tolerance.

Joe, a technician, installs a new Blu-Ray player via an external cable. The PC has previously had a USB 3.0 expansion card installed into its PCI Express slot. When Joe powers on the Blu-Ray player, he notices the "USB 2.0 Device" pop up in the Windows System Tray. Which of the following are probable causes? (Select TWO). A. A virus is attacking the USB 3.0 driver, forcing it to operate in USB 2.0 mode only. B. The Blu-Ray player is plugged into the wrong port on the back of the PC. C. The Blu-Ray player was mistakenly plugged into the FireWire port. D. The Bluetooth connection from a nearby mobile device is interfering with the Blu-Ray player. E. The Blu-Ray player had a DVD loaded into it and this caused the computer to malfunction. F. The technician that installed the USB 3.0 expansion card forgot to install the USB 3.0 driver.

Answer: B,F Explanation: The possible causes might be that the Blu-ray players was plugged into the firewire port mistakenly or the technician that installed USB 3.0 expansion card forgot to install the drivers for it.

Which of the following would allow for multiple computers to share a display and input devices? A. AGP video adapter B. KVM switch C. Portable TDR D. PCI video adapter

Answer: B. KVM switch(Reference:http://www.prosum.net/en/products/kvm-switches)

Video editing workstations require the fastest hard drive access times with large storage capacity. Which of the following hard disk setups would be MOST ideal for the described computer? A. Two 500 GB SATA2 hard drives used in a JBOD array B. Two 500 GB SATA2 hard drives in a hardware RAID 0 C. Two 500 GB SATA2 hard drives in a hardware RAID 1 D. Two 500 GB SATA2 hard drives in a software RAID 0

Answer: B. Two 500 GB SATA2 hard drives in a hardware RAID 0 (Reference:http://forums.mydigitallife.info/threads/12651-2x-200GB-SATA-I-Raid-0-v-s-single500GB-SATA-II)

Which of the following is the form factor of a standard Parallel connector? A. DB-9 B. DB-15 C. DB-25 D. DIN-6

Answer: C Reference:http://en.kioskea.net/contents/180-db25-connector he DB25 (originally DE-25) connector is an analog 25-pin plug of the D-Subminiature connector family (D-Sub or Sub-D). As with the DB9 connector, the DB25 is mainly used for serial connections, allowing for the asynchronous transmission of data as provided by standard RS-232 (RS-232C). It is also used for parallel port connections, and was originally used to connect printers, and as a result is sometimes known as a "printer port" (LPT for short).

A user wishes to dispose of a CRT monitor that is no longer working. Which of the following steps should a technician complete before proceeding with the disposal? A. Break the glass in the CRT in a controlled environment to prevent injury B. Discharge all capacitors in the CRT and remove them before disposal C. Ensure familiarity and compliance with all relevant local regulations D. Ensure that the monitor is no longer working and repair if possible

Answer: C Explanation: CRT monitor has lead, which is a toxic component of the cathode tube. In order to dispose off properly, you need to be familiar with state and local regulations.

When comparing analog display inputs to digital display inputs, which of the following is an advantage that digital has over analog? A. Allows for higher brightness B. More crosstalk C. Sustains higher resolutions D. Supports widescreen resolutions

Answer: C Explanation: Digital can sustain higher resolutions whereas analog display has limited resolution.

Which of the following characteristics BEST differentiates a Home Theatre PC from a CAD PC? A. Ability to play optical media B. Gigabit network connection C. Small form factor D. Ability to edit large files

Answer: C Explanation: Home theater PC has a small form factor normally essentially a bookcase in a shelf styled computer that player audio and video. CAD PC needs a lot of muscle like vast amount of memory, video cards, and essentially other high performance parts. Therefore, the main difference between home theater PC and a CAD PC is the form factor which houses essential components.

Which of the following devices might need drivers installed so that it can be recognized by the operating system and function properly? A. Speakers B. Monitors C. Scanners D. Projectors

Answer: C Explanation: Scanner is a peripheral device that needs drivers to function properly. A scanner will not be able to show the scanned page on the computer until it has the necessary files to transfer the data to a PC.

A technician would like to connect to a computer using remote desktop. Which of the following ports does remote desktop use by default? A. 22 B. 443 C. 3389 D. 8080

Answer: C Explanation: The default port for remote desktop application is 3389. Reference:http://windows.microsoft.com/en-us/windows7/allow-remote-desktop-connections-from outside-your-home-network(see forward TCP port 3389)

The helpdesk technician has been tasked to reinstall the OS on a desktop and has already inserted the OS install disk in the CD-ROM. Which of the following would MOST likely need to be configured within the BIOS to continue reinstalling the OS? A. BIOS password B. Flash BIOS for firmware upgrade C. Boot sequence D. Clock speeds

Answer: C Explanation: To boot the OS from the CD ROM, you need to change the boot sequence to boot from CD ROM first. Normally, the boot sequence is to boot from hard disk and if it is unable to find boot files there, it will look for it in a CD ROM. After that, it will look into other places like a floppy disk drive and PXE boot.

A technician is asked to upgrade RAM in a laptop from 4GB to 8GB. Which of the following should the technician do FIRST? A. Download the newest motherboard drivers B. Enable TPM C. Review the vendor laptop documentation D. Flash the BIOS

Answer: C Explanation: To upgrade, you need to know what is compatible. Read vendor laptop documentation before upgrading RAM, CPU or a hard drive.

Which of the following cable types has the MAXIMUM transfer rate of 1 Gbps? A. CAT3 B. CAT5 C. CAT5e D. CAT6

Answer: C Reference:http://customcable.ca/cat5-vs-cat6/(see CAT5e)

Which of the following connector types is only used for Coaxial? A. RJ-11 B. ST C. F D. RJ-45

Answer: C Reference:http://en.wikipedia.org/wiki/F_connector

Which of the following types of RAM can be used in a dual channel configuration? A. SDRAM B. RAMBUS C. DDR D. DIMM

Answer: C Reference:http://en.wikipedia.org/wiki/Multi-channel_memory_architecture#Dualchannel_architecture

The MAXIMUM transfer rate of eSATA is: A. 1.54 Mbps. B. 2.0 Gbps. C. 3.0 Gbps. D. 480 Mbps.

Answer: C Reference:http://en.wikipedia.org/wiki/Serial_ATA

The term SFF refers to which of the following? A. CPU speed B. Memory size C. Motherboard size D. HDD size

Answer: C Reference:http://en.wikipedia.org/wiki/Small_form_factor

Which of the following devices would provide protection for electronic equipment in an area prone to intermittent, unstable power? A. Power strip B. Surge suppressor C. Uninterruptible power supply D. Line conditioner

Answer: C Reference:http://pcsupport.about.com/od/componentprofiles/p/ups_backup.htm

A technician is tasked with improving the speed at which a system boots and loads applications as well as improving data availability. Which of the following should the technician implement? A. Upgrade external storage to USB 3.0 B. Upgrade non RAID hard drives to SSD C. Configure software RAID 5 D. Install additional eSATA drives

Answer: C Reference:http://www.adaptec.com/nr/rdonlyres/14b2fd84-f7a0-4ac5-a07a214123ea3dd6/0/4423_sw_hwraid_10.pdf

Which of the following adapters causes the LEAST amount of signal loss? A. VGA to DVI B. HDMI to VGA C. DVI to HDMI D. S-video to RCA

Answer: C Reference:http://www.buzzle.com/articles/dvi-vs-hdmi-difference-between-dvi-and-hdmi.html(3rd para)

Which of the following characteristics is generally found on a docking station that port replicators do not offer? A. Replicators usually have more USB ports than docks. B. Docks generally do not need separate power to function. C. Docks have independent hardware that replicators lack. D. Replicators have additional NIC that docks lack.

Answer: C Reference:http://www.computerhope.com/jargon/d/dockstat.htm

Which of the following RAM types supports triple channel configurations? A. RAMBUS B. DDR C. DDR3 D. DDR2

Answer: C Reference:http://www.hardwaresecrets.com/printpage/Everything-You-Need-to-Know-About-theDual-Triple-and-Quad-Channel-Memory-Architectures/133

105 Which of the following would provide continuous power to various devices connected to it during a power surge or outage? A. Line conditioner B. Power strip C. Battery backup D. Surge suppressor

Answer: C Reference:http://www.howtogeek.com/161479/how-to-select-a-battery-backup-for-your-computer/

Which of the following allows a technician to enable support for a USB 1.1 device? A. MBR B. HCL C. BIOS D. AGP

Answer: C Reference:http://www.tomshardware.com/forum/82823-45-enable-bios-keyboard-support

Which of the following input devices allows multiple PCs to share a common display? A. Router B. Bridge C. KVM D. Wireless keyboard

Answer: C Reference:http://www.webopedia.com/TERM/K/KVM_switch.html Short for keyboard, video, mouse switch, a hardware device that enables a single keyboard, video monitor and mouse to control more than one computer one at a time.

Which of the following connections are typically on the external PC chassis? (Select TWO). A. AGP B. SAS C. IEEE1394 D. eSATA E. IDE

Answer: C,D Explanation: IEEE1394 commonly known as Firewire port and eSATA connections are typically located on the external PC chassis. Firewire port is a serial bus interface that works like a USB. eSATA connection are typically external hard disks.

Which of the following external ports would a technician use to connect a keyboard? A. eSATA B. IEEE 1394 C. USB D. PS/2 E. VGA

Answer: C,D Explanation: Keyboard connects to PS/2 (old computers) and USB. Nowadays, all most all the keyboards are USB devices. PS/2 port is obsolete.

After setting up a new computer, a user states that the mouse and keyboard will not work. Which of the following is the MOST likely reason? A. The network cable is disconnected B. The PS/2 connectors are switched C. The USB connectors are switched D. The hard drive is unplugged

Answer: B Explanation: It is normal to switch the PS/2 connectors in older computers. PS/2 connectors are present side by side at the back of a computer casing. Both are colored to avoid switching but sometimes the keyboard is switched to a mouse PS/2 port and the mouse is connected to keyboard PS/2 port. So first check PS/2 connector to see whether the problem lies with PS/2 connectors.

RG-59 is a designation for which of the following cable types? A. Plenum B. Fiber optic C. Twisted pair D. Coaxial Answer: D Reference:http://en.wikipedia.org/wiki/RG-59

Answer: D Reference:http://en.wikipedia.org/wiki/RG-59

Which of the following is a standard Intel processor socket type? A. F B. 754 C. 940 D. LGA

Answer: D Reference:http://en.wikipedia.org/wiki/Land_grid_array

A technician is building a gaming PC for a user. The user wants to dual boot between Windows XP 32-bit and a 64-bit version of Windows 7 as some of the games require XP. The user requests the following specifications: 64-bit i7 processor, (consisting of 6 cores @ 3.0GHz) 16 GB of RAM (consisting of two 8 GB modules) One 200 GB SSD RAID 1 (consisting of two 1TB SATA Drives) Two 2 GB SLI Video Cards Which of the following components should the technician warn the user will be reported differently depending on the operating system that is currently booted? A. RAID B. RAM C. Processor D. SSD Drive E. Video Card

Answer: B Reference:http://en.wikipedia.org/wiki/Random-access_memory Random-access memory (RAM /ræm/) is a form of computer data storage. A random-access memory device allows data items to be accessed (read or written) in almost the same amount of time irrespective of the physical location of data inside the memory. Today, random-access memory takes the form of integrated circuits. RAM is normally associated with volatile types of memory (such as DRAM memory modules), where stored information is lost if power is removed, although many efforts have been made to develop non-volatile RAM chips.[1] Other types of non-volatile memory exist that allow random access for read operations, but either do not allow write operations or have limitations on them. These include most types of ROM and a type of flash memory called NOR-Flash

Which of the following adapter types uses a 7-pin cable to transmit video signals? A. RGB B. S-Video C. HDMI D. DVI

Answer: B Reference:http://geoffthegreygeek.com/s-video/#.UitCfGQS2Qk

Which of the following display connections has 15-pins? A. RGB B. VGA C. DVI D. HDMI

Answer: B Reference:http://pinouts.ru/Video/VGA15_pinout.shtml

The Tower of Hanoi is MOST likely configured in a system which implements: A. a high RPM drives. B. a tape drive. C. an externally attached storage. D. a RAID configuration.

Answer: B Reference:http://searchdatabackup.techtarget.com/definition/Tower-of-Hanoi-backups Tower of Hanoi is a complex tape backup strategy that's useful for archiving data for an extended period of time in an economical manner. To solve Lucas' puzzle, the player must move all the discs from the first pole to the third pole in the fewest possible moves.

Ann, a home user, would like to connect her laptop display to her home HD television. Which of the following is the BEST solution? A. Connecting the laptop's VGA output to an HDMI adaptor B. Connecting the laptop's VGA output to the television's VGA input C. Connecting the laptop's USB output to the HD television's HDMI adaptor D. Connecting the laptop's USB output to the television's USB input

Answer: B Reference:http://sewelldirect.com/articles/How-To-Connect-Laptop-To-TV.aspx

A user already has 2 RAM modules in a 64-bit Windows 7 PC. Each is a 1GB DDR-PC1600 RAM module. The user has 2 additional RAM modules that are each 2GB DDR-PC800. Which of the following is true about the PC after installing the additional RAM modules? A. The system only accesses the pair of 2GB RAM modules B. The system accesses all RAM at 100MHz C. The system enables ECC on all RAM modules D. The system will not work as all RAM has to be equal sizes

Answer: B Reference:http://whatis.techtarget.com/reference/Fast-Guide-to-RAM

Which of the following types of connectors would be found to connect printers and scanners to a device that did not have any network connections? A. RJ-45 B. Parallel C. RJ-11 D. BNC

Answer: B Reference:http://wiki.answers.com/Q/What_is_a_parallel_connector

Which of the following hard drive types would be considered the MOST likely to survive a fall? A. SCSI B. Solid State C. IDE D. SATA

Answer: B Reference:http://www.examiner.com/article/solid-state-drives-vs-hard-drives

Which of the following connectors from a power supply should be used with a graphics expansion card? A. 8-pin 12 volt B. PCIe 6-pin C. 20-pin D. SATA Answer: B Reference:http://www.maplin.co.uk/pci-express-power-converter-46857

Answer: B Reference:http://www.maplin.co.uk/pci-express-power-converter-46857

Which of the following devices requires 12V of power from the power supply? A. Serial Port Card B. CD-ROM Drive C. Parallel Port D. Audio Jack

Answer: B Reference:http://www.mrjentis.com/cdplayer_adapter.html(Introduction, second para)

An end user is designing a PC with a clear acrylic access panel to show off the insides. The user wants the inside to stay cool, but as dust free as possible. Which of the following would BEST meet this scenario? A. Create a positive pressure air flow with unfiltered intakes and filtered exhausts B. Create a positive pressure air flow with filtered intakes and unfiltered exhausts C. Create a negative pressure air flow with unfiltered intakes and unfiltered exhausts D. Create a negative pressure air flow with filtered exhausts and unfiltered exhausts

Answer: B Reference:http://www.overclock.net/t/1219634/positive-air-pressure-what-you-need-to-know-tokeep-your-pc-clean-and-happy

Which of the following is the BEST way to explain RAID to a non-technical user? A. "RAID is a dynamic logical disk management system." B. "RAID uses multiple hard disks to increase performance and/or provide protection against data loss." C. "RAID uses data striping to reduce hard drive write time and parity bits to reconstruct the data from a failed hard drive." D. "RAID stands for Redundant Array of Independent Disks".

Answer: B Reference:http://www.pcworld.com/article/132877/RAID.html

Thermal paste is used with which of the following components? A. Fan B. Heat sink C. Motherboard D. RAM

Answer: B Reference:http://www.techpowerup.com/articles/overclocking/134

Which of the following expansion cards would MOST likely have the requirements of utilizing a direct auxiliary 6-pin power plug to operate properly? A. PCI Express RAID card B. PCI Express video card C. PCI Express FireWire card D. PCI Express LAN card

Answer: B Reference:http://www.tomshardware.com/reviews/power-supply-specifications-atxreference,3061-12.html

A user is requesting assistance in building a custom made PC for home theater use to connect to their existing large LCD screen. Which of the following components should MOST likely be recommended? (Select TWO). A. Large IDE hard drive B. HDMI output C. Dual monitors D. RAID array E. TV tuner

Answer: B,E Explanation: A Home theater PC is also a TV. So you need to have a TV tuner card that will show cable on the home theater PC. You would also need an HDMI output to connect the PC to a large LCD screen for optimal viewing.

Which of the following are examples of multimedia devices? (Select TWO). A. Scanner B. Digitizer C. Webcam D. Microphone E. Touchscreen Answer: C,D Explanation: Multimedia is the integration of multiple forms of media. This includes text, graphics, audio, video, etc. For example, a presentation involving audio and video clips would be considered a "multimedia presentation." Educational software that involves animations, sound, and text is called "multimedia software." CDs and DVDs are often considered to be "multimedia formats" since they can store a lot of data and most forms of multimedia require a lot of disk space. Webcam incorporates both audio and video. Similarly, microphone is a multimedia device because it incorporates sound and it can also be used for various applications. Touchscreen, scanner and digitizer are input devices because they require input from the user to function properly.

Answer: C,D Explanation: Multimedia is the integration of multiple forms of media. This includes text, graphics, audio, video, etc. For example, a presentation involving audio and video clips would be considered a "multimedia presentation." Educational software that involves animations, sound, and text is called "multimedia software." CDs and DVDs are often considered to be "multimedia formats" since they can store a lot of data and most forms of multimedia require a lot of disk space. Webcam incorporates both audio and video. Similarly, microphone is a multimedia device because it incorporates sound and it can also be used for various applications. Touchscreen, scanner and digitizer are input devices because they require input from the user to function properly.

Which of the following are the MOST important considerations when configuring a PC that will be used for a CAD / CAM workstation? (Select TWO). A. Gigabit NIC B. HDMI output C. Maximum RAM D. Powerful processor E. High end audio output

Answer: C,D Reference:http://www.physicsforums.com/showthread.php?t=499107

Which of the following technologies can be accessed through the DisplayPort? (Select TWO). A. USB B. SATA C. DVI D. FireWire E. HDMI

Answer: C,E Reference:http://www.tomshardware.com/forum/390436-33-hdmi-display-port-hdmi

Which of the following are standard AMD processor socket types? (Select TWO). A. 1366 B. 1155 C. socket 940 D. LGA E. Socket F

Answer: C,E Reference:http://www.wisegeek.com/what-is-socket-940.htm Socket F replaced socket 940

Which of the following expansion slots uses a serial connection? A. PCI B. PCI-X C. PCIe D. AGP

Answer: C. PCIe (Reference:http://en.wikipedia.org/wiki/PCI_Express#Serial_bus)

Two new PCs will have a DVD-RW drive for support use. The PCs will be used for Point of Sales transactions and everything will be password protected or disabled. Which of the following is the BEST way to disable the DVD-RW drives? A. The Registry B. Device Manager C. Disk Management D. The BIOS

Answer: D Explanation: BIOS settings directly affect hardware. You can disable DVD-RW drives from the BIOS and it is perhaps the best way to keep the drives disabled. In BIOS menu, there is an option to disable the DVD drives.

Which of the following MUST be configured when trying to start a machine with a DVD? A. TPM B. Virtualization support C. BIOS security D. Boot order

Answer: D Explanation: By default BIOS boot order is configured to boot the computer from the hard disk. When installing Windows from a DVD or any other OS, you need to set the preferred boot order to DVD so the computer can scan the DVD drive to get the boot data and boot from the DVD.

A customer has asked for the ability to operate dual digital monitors. Which of the following is the BEST solution for accomplishing this? A. Split the onboard video port. B. Update the video drivers to allow for multiple monitors. C. Add an adaptor to the onboard VGA port. D. Install a video card with multiple DVI ports.

Answer: D Explanation: Dual digital monitors can be easily setup by using a video card with multiple DVI ports. You can set up as many monitors as the DVI ports on the video card allow you to do so.

Ann, a user, has recently installed a new Blu-Ray ROM in her desktop computer. The computer recognizes the device as a DVD-ROM. Which of the following actions would enable the system to recognize the device as a Blu-Ray device? A. The operating system must be upgraded to Windows Ultimate. B. Flash the system's motherboard CMOS. C. Upgrade to the latest Windows Media Player. D. Install the manufacturer's drivers for the OS.

Answer: D Explanation: Install the drivers that came with the Blu-ray ROM. Without the drivers, the computer might not recognize the drive.

Which of the following are factors when designing a home theater PC? A. Wireless NIC B. Audio frequency C. Video refresh rate D. Video output

Answer: D Explanation: Video output is the main factor in building a home theater PC. You need to connect the TV or a large display with a PC and HDMI, DVI outputs are needed to show the PC on the display screen.

Which of the following would be the MOST important factor to consider when building a virtualization workstation? A. High-end graphics card with onboard memory B. A compact form factor C. Dual monitor support D. Maximum RAM and CPU cores

Answer: D Explanation: Virtualization requires a lot of memory and processing power. If you install 2 or 3 operating systems, you will be needing memory and processors to keep them running in optimal condition. Therefore, you need maximum RAM and CPU cores to make sure you have enough resources for your virtualization platform.

Which of the following should a technician do NEXT after reporting an incident? A. Delete the content B. Confiscate the PC C. Go back to work D. Document the incident

Answer: D Explanation: When the incident is reported, the best thing to do afterward is to document the details of the incident especially in the hardware case. The documenting of the incident will help determine the cause of the problem and the circumstances in which the problem occurred.

Which of the following uses a single connector to deliver both video and audio? A. DVI B. Serial C. VGA D. HDMI Answer: D HDMI (Reference:http://hometheater.about.com/od/hometheatervideobasics/qt/hdmifacts.htm)

Answer: D (Reference:http://hometheater.about.com/od/hometheatervideobasics/qt/hdmifacts.htm)

A home user's PC has an over-clocked CPU with a relatively small heat sync, small fans on the 800W power supply, and a high-end video card. Which of the following is the recommended solution that will manage heat more effectively? A. Replace the CPU heat sync with a high RPM fan B. Purchase an energy efficient power supply C. Not over-clocking the CPU D. Liquid cooling system

Answer: D Reference:http://computer.howstuffworks.com/liquid-cooled-pc.htm


Kaugnay na mga set ng pag-aaral

International migration midterm :()

View Set

Operating Systems Chapter 2 Review

View Set

CA HA 7 LOWER appendicular skeleton

View Set

Child Development and Stages (Infant/Toddler/Pre-schooler/School-Age/Adolescent)

View Set

Quiz 5 - cropping, resizing, and rotating

View Set

Bushong 1-1 Nature of our Surroundings

View Set