ITExams - CompTIA A+ Core 1 Practice Test
A
A systems administrator receives a notification from the RAID controller that the RAID 5 array is degraded. Upon logging into the server, the administrator sees that on logical disk 0, physical disk 2 has failed. Which of the following is the BEST course of action to take to resolve the problem? A. Schedule system downtime and replace physical disk 2. Wait until the array is rebuilt and confirm in the RAID controller that the system is no longer degraded. B. Immediately replace physical disk 2. Wait until the array is rebuilt and confirm in the RAID controller that the system is no longer degraded. C. Delete logical disk 0 and manually configure a new RAID array only using the known-good working drives. Wait until the array is rebuilt and confirm in the RAID controller that the system is no longer degraded. D. In the controller, convert the RAID 5 array to RAID 0 array to avoid system downtime. Wait until the array is rebuilt and confirm in the RAID controller that the system is no longer degraded.
A
A technician is dispatched to troubleshoot a slow performance issue on a PC. Upon arrival, the technician immediately opens Task Manager and sees that CPU and RAM performance are within normal ranges. The technician then checks and verifies the speed and duplex settings and performance on the network card.The technician then temporarily disables the antivirus to see if performance is affected, and it is not. After re-enabling the antivirus, which of the following is theNEXT best step for the technician to take? A. Check to see if insufficient hard drive space is causing the issue B. Update the operating system, drivers, and firmware on the PC C. Log into the PC with another user profile and test performance D. Shut down the PC, unplug the power for 30 seconds, and then boot the PC
A
A technician is hired to install network cable in a crawl space running the length of a hallway. To do so without a fire code violation, which of the following types of cable should the technician run? A. Plenum B. Fiber C. Shielded D. Coaxial
B
An end user has signed up to use a web-based calendar application.Which of the following solutions has the user purchased? A. DaaS B. SaaS C. PaaS D. IaaS
A
Which of the following devices performs forwarding decisions based on MAC addresses? A. Switch B. Router C. Hub D. Repeater
C
Company management wants to give users the ability to work from home during periods of bad weather. Which of the following would enable the workforce to do this? A. NAT B. VLAN C. VPN D. HIPS
A
Some users are unable to access the Internet form their workstations. A technician runs the ipconfig command on one of the workstations and sees the following (IMAGE): The technician pings 8.8.8.8 and gets no response. Next, the technician pings 192.168.1.1 and gets no response. The technician is able to successfully ping an adjacent workstation but cannot ping the print server on the floor below. Which of the following is the MOST likely cause of the Internet connectivity issue in the office? A. There is a problem with a router in the office B. There is a problem with a DNS server in the office C. The users are not getting correct IP addresses from the DHCP server D. The wireless access point in the area is down
A
A business owner wants to provide security to laptop users with the ability to charge their devices, access corporate LAN resources, and allow for a variety of other removable hardware.Which of the following devices would BEST meet the ownerג€™s needs? A. Docking station B. Port replicator C. Thunderbolt D. USB hub
AB
A client has three locations within city limits that need to be networked. Vendor network requirements for all three locations are a minimum of 1GB.Which of the following are the types of networks that will MOST likely be used for internal office and office-to-office networking? (Choose two.) A. MAN B. LAN C. WAN D. PAN E. SAN F. WLAN
A
A company has very strict rules regarding proprietary information leaving the premises. All computers host proprietary information. A technician is called to repair a computer on-site at the companyג€™s corporate office. The technician identifies the problem and goes through the troubleshooting steps to create a plan of action.The technician determines the computer needs to be taken off-site for repair.Which of the following should the technician do NEXT? A. Check corporate policies for guidance. B. Get authorization from the manager. C. Delete proprietary data before leaving the building. D. Remove the HDD and send the device for repair.
A
A company offers several out-of-the-box computer configurations to its clients. A client requests several new computers for its newest location, which will be used by guests to check in upon arrival and fill out contact information. Which of the following configurations would BEST fit this customerג€™s needs? A. Touch-screen kiosk B. Thick client C. CAD workstation D. Virtualized host computer
C
A customer accidentally drops a laptop while it is charging. The next day, the customer notices the laptop will not turn on and calls a technician to investigate. The technician confirms the laptop will not turn on even though it is connected to the power adapter.Which of the following components is the MOST likely cause of this behavior? A. Power adapter B. Battery C. DC jack D. Hard drive
AB
A customer asks a technician to help set up a specialized computing system for video editing.Which of the following should the technician install on the workstation to BEST meet the customerג€™s specifications? (Choose two.) A. SSD B. Dual monitors C. Gigabit NIC D. Hypervisor E. Docking station F. NAS
A
A customer recently moved a high-end graphics card from a known-working computer to a different computer. The computer works without issue when viewing email and web pages or when using certain applications. However, when a game with high-end graphics requirements is opened, the program will run for a few minutes before the computer shuts down. Which of the following is MOST likely causing the problem? A. Power supply wattage B. Video RAM C. CPU frequency D. Monitor resolution
A
A customer wants to upgrade a PCג€™s internal storage to have more room to store backups, photos, and videos. The new storage should be large enough to avoid expanding again next year.Which of the following BEST meets these needs? A. 3TB HDD B. 50GB NAS C. 500TB SAN D. 512GB SSD
B
A customerג€™s laptop display has suddenly become very dim. The image of the display can only be seen with a bright, external light, as adjusting the brightness/ contrast controls does not cause much change.Which of the following components MOST likely needs to be replaced? A. LCD panel B. Inverter C. Video card D. Digitizer
A
A laptop is connected to a conference room projector in extended display mode. The desktop icons appear normal on the laptop, but are disproportionate and illegible on the projector screen. Which of the following should the technician check? A. Video resolution B. HDMI connection C. Keystone D. Focus
A
A network administrator is attempting to access the firewall while inside the datacenter. Which of the following peripherals must be connected to do so? A. KVM B. Touchpad C. Mouse D. Keyboard
D
A network administrator is troubleshooting a notebook that is not loading the local Windows 10 operating system. All the computers inside the company are installed using UEFI mode selected. The message on the screen shows a failed attempt to connect to a PXE server. When requested, the end user reported trying to improve the computerג€™s speed by changing some BIOS configurations randomly. Which of the following should the network administrator check FIRST insideBIOS? A. C-states should be configured to 2 B. Secure Boot should be enabled C. Wake-on-LAN should be unchecked D. The PXE server address should be set
A
A network administrator must install a device that will proactively stop outside attacks from reaching the LAN.Which of the following devices would BEST meet the organizationג€™s needs? A. IPS B. IDS C. Proxy server D. Authentication server
A
A printer stops working in the billing department and cannot be repaired. A new printer has been ordered and a technician is tasked with allowing other users to print to the billing managerג€™s printer until the new printer arrives. The managerג€™s printer is currently used via USB connection, and there are no network jacks available for use.Which of the following is the BEST way for the technician to allow access to the printer? A. Create a share on the managerג€™s computer and give the users rights to the share. B. Install the printer on the usersג€™ desktops and point it to the IP address of the managerג€™s computer. C. Purchase a wireless printer so the users can access the printer via the network. D. Provide flash drives to the users so they can transfer data to the managerג€™s computer for printing.
A
A projectorג€™s image begins to flicker during a presentation. The laptop display does not produce this issue.When a technician changes the resolution on the laptop, the issue persists. Which of the following is the NEXT step the technician should take? A. Check the connectivity of the VGA cable. B. Check the connectivity of the power cable. C. Change the aspect ratio on the laptop. D. Change the settings of the projector.
DEH
A server administrator set up a VM to be used in a lab setting. A technician is setting up thin-client computers to access this VM. Which of the following tasks are required to complete the project? (Choose three.) A. Connect the device to a printer. B. Install the operating system. C. Install a USB keyboard and mouse. D. Connect the device to the network. E. Install the latest system updates. F. Install the latest device drivers. G. Connect the device to a monitor. H. Install the necessary applications.
B
A server needs a RAM upgrade, and a technician has been tasked with retrieving the RAM from storage and then installing it.Which of the following is the BEST RAM type for the technician to retrieve? A. SoDIMM B. DDR4 C. Single channel D. ECC
A
A shipping department is having problems with its thermal label printer. Two columns on the left are not appearing on all labels. Which of the following should a technician do FIRST? A. Verify the ribbon is correctly aligned to the label B. Run a label calibration C. Remove stuck labels from the print path D. Replace the print head
A
A systems administrator is configuring a server to host several virtual machines. The administrator configures the server and is ready to begin provisioning the virtual machines.Which of the following features should the administrator utilize to complete the task? A. Hypervisor B. Disk management C. Terminal services D. Device Manager E. Virtual LAN
AB
A technician has been asked to fix a problem with a projector. The projector lamp turns off for brief periods during a demonstration. After the technician replaced the lamp, the problem continued with an added message that appears just before the lamp turns off. Which of the following MOST likely need to be performed?(Choose two.) A. Reset the lamp life counter B. Replace the cooling fan C. Adjust the brightness D. Update the laptop video driver E. Install a higher lumen lamp F. Change the video resolution
B
A technician has been informed that multiple users are receiving duplicate IP address warnings on their workstations, and they are unable to browse the Internet.Which of the following server types should the technician log in to in order to resolve the problem? A. DNS server B. DHCP server. C. Proxy server D. RADIUS server
A
A technician has noticed that when at company headquarters the laptop connection to the Internet is more responsive than when using the company-provided phone as a hotspot. The technician updated the drivers on the WiFi NIC without resolution and then verified the configuration on the WiFi was correct.Which of the following configurations could cause the decreased performance? A. The connection is throttled. B. There is a low RFID signal. C. SSID is not found. D. It is out of range.
B
A technician is buying a laptop that will host three VMs running at the same time with the current configuration. The technician believes there might be a need to run several additional VMs in the near future. Which of the following resources would be the MOST important to upgrade to allow for the additional VMs? A. CPU B. SSD C. NIC D. RAM
C
A technician is configuring a high-performance workstation. The technician needs to choose storage for the boot drive with the highest performance possible.Which of the following drive types BEST meets this requirement? A. MicroSD B. 15K rpm C. NVMe D. USB flash
A
A technician is determining the specifications for a desktop computer that will be used at trade shows all over the world. The computer will have the maximum amount of RAM. The CPU, GPU, and storage will be typical of a business workstation.Which of the following system parameters is the MOST important for the technician to consider when choosing a power supply? A. Input voltage B. Efficiency rating C. 12V rail amperage D. Number of SATA connectors
B
A technician is ordering a new motherboard and processors for a company email server. When reviewing the vendor licensing agreement, the technician sees that there is a flat per-socket licensing fee.Which of the following motherboard/processor combinations should the technician order to get the BEST performance while minimizing licensing fees? A. A dual-processor motherboard with six hyperthreaded cores each. B. A single-processor motherboard with eight hyperthreaded cores. C. A dual-processor motherboard with eight overclocked cores each. D. A single-processor motherboard with ten overclocked cores.
A
A technician is replacing a broken screen on a new company laptop but does not have repair information from the vendor.Which of the following is the BEST way to proceed? A. Document and label the cable and screw locations. B. Replace the screen with a non-OEM. C. Update the firmware on the device before repairing it. D. Wait for the vendor to provide more information.
B
A technician is replacing an older video card with a new high-end video card in a workstation. The installation was successful, the new card seated properly, and power is connected. However, upon booting, the computer now emits several beeps and will not boot, but shows no error messages. Which of the following isMOST likely the cause of this issue? A. The BIOS is out-of-date B. The is not enough PSU output C. There is an onboard RAM mismatch D. GPU is overlocked E. The firmware is out-of-date
D
A technician is replacing the LCD panel in a laptop. Which of the following components is MOST likely to be damaged accidentally during the repair? A. Bezel B. Hinge C. Motherboard D. Digitizer
C
A technician is setting up a VM for use in testing software deployments. The VM is offline, but the hypervisor is not.Which of the following settings should the technician change to resolve this issue? A. Virtual security B. Virtual storage C. Virtual CPU D. Virtual switch E. Virtual RAM
AC
A technician is setting up a WiFi-enabled thermostat for a customer, but the customer is concerned about IoT devices getting hacked.Which of the following BEST address the customerג€™s concerns? (Choose two.) A. Use the latest encryption standard on the wireless network and set a strong password. B. Enable two-factor authentication for the IoT deviceג€™s cloud account, if it is available. C. Separate the IoT thermostat by segregating it in a DMZ network. D. Disable wireless access on the thermostat to make it unshakable. E. Upgrade the customerג€™s router to the latest version to improve network security. F. Upgrade the customerג€™s wireless network encryption to WPA.
A
A technician is setting up a Windows mobile device for a user who had trouble reading text on a previous device, especially at night.Which of the following adjustments would be MOST appropriate? A. Use the magnifier. B. Increase the resolution. C. Use haptic feedback. D. Utilize text-to-speech.
A
A technician is setting up a new wireless network at a branch office that previously had only wired connectivity with statically assigned IP addresses. After setting up the network, the technician configures a server to provide IP addresses to wireless clients. During testing, the technician is unable to access the Internet or named network resources. The technician receives a valid IP address from the DHCP server and can ping the default gateway.Which of the following should be technician check NEXT to resolve this issue? A. Ensure the options are configured to provide a DNS server. B. Verify the Windows Firewall is turned off. C. Configure the wireless networkג€™s SSID to be hidden. D. Enable file and printer sharing in the OS.
A
A technician is setting up a printer for a small office that does not have an RJ-45 jack. The usersג€™ computers are all in the same workgroup and are connected physically to the same network switch. The technician needs to make sure all users can print to the new printer through the switch. Which of the following should the technician configure? A. Shared printer B. Print server C. Bluetooth printing D. Cloud printing
D
A technician is talking to end users about the specifications for an upgraded application server. The users of the application report that there cannot be any unscheduled downtime or data loss. Additionally, they would like the performance of the application to improve over the previous server in any way possible. The previous server was running RAID 5.Which of the following RAID solutions should be implemented in this scenario? A. RAID 0 B. RAID 1 C. RAID 6 D. RAID 10
B
A technician is troubleshooting a Windows CAD workstation that is running slow. The computer uses RAID 10 and has dual GPU cards. The user states that the same application runs faster on an identical workstation.Which of the following should the technician perform FIRST to troubleshoot the problem? A. Replace the write cache battery. B. Check the event log for any cache issues. C. Clear the RAID configuration file and restart the PC. D. Replace the RAID controller write cache module.
AB
A technician is troubleshooting a laptop/projector combination that is displaying artifacts on the screen. When a different laptop is connected to the projector, the image appears to be correct but is very dim.Which of the following steps should the technician take to address these issues? (Choose two.) A. Update the video drivers on the laptop. B. Increase the projector contrast. C. Replace the original laptop. D. Change the aspect ratio on the projector. E. Replace the bulb in the projector. F. Modify the laptopג€™s display resolution.
A
A technician is troubleshooting network connectivity issues after a new wireless router was installed in an office. Users who connect to the new router are unable to access LAN resources. Which of the following is the MOST likely cause of the issue? A. There are conflicting DHCP servers on the network B. There are conflicting ARP records C. There are conflicting gateways on the network D. There are conflicting IP protocols
Continuous reboots
A technician is troubleshooting what appears to be a RAM issue on a PC. Which of the following symptoms would indicate if this is a RAM issue?
EF
A technician needs to routinely run scripting commands in Linux but does not want to walk over to the server room every time to perform the task. The technician also travels between buildings and has a Windows 10 laptop with 4GB of memory and a fully partitioned 500GB hard drive.Which of the following steps should the technician take to resolve this issue? (Choose two.) A. Increase the memory to 8GB. B. Install a Linux guest VM. C. Add another 500GB hard drive. D. Create a Linux LiveBoot CD. E. Repartition the hard drive. F. Install Linux on a new ext3 partition.
A
A technician receives a cellular call from a manager. The technician is instructed to download a service manual directly from the Internet to a laptop. However, there is no WiFi signal or wired Ethernet. Which of the following would be the MOST appropriate connections for the technician to use? A. Hotspot B. NFC C. Bluetooth D. VPN
ACD
A technician replaced a broken LED screen on a mobile computer. The operating system can be seen perfectly on screen, but the touch screen is non-responsive.Which of the following are the MOST probable root causes for the given failure? (Choose three.) A. The hardware replacement used is a non-touch-screen version. B. The touch screen must be calibrated after a replacement. C. The digitizer cable is not seated properly on the motherboard. D. The new touch-screen drivers must be installed. E. The replacement part is dead-on-arrival. F. The LCD panel firmware must be updated. G. The grounding screws are not securely attached.
D
A technician upgraded the memory on a server from two 8GB sticks to eight 32GB sticks. The server memory is now at full capacity per the user guide. When the technician powers on the system, only 128GB of memory is recognized by the OS and the BIOS. The technician decides to upgrade to the latest version of the firmware on the system, which does not help. Next, the technician installs the memory in sets of 64GB at a time. Each individual set of 64GB is fully recognized by the server.Which of the following will not allow the server to recognize all of the memory installed at the same time? A. The power supply is not supplying enough power for the memory. B. The memory has too many ECC errors and is shutting down C. The server is overheating when all of the memory is installed. D. The server needs DDR4 memory, and DDR3 is installed.
A
A technician wants to block remote logins to a server. Which of the following ports should be blocked? A. 21 B. 53 C. 80 D. 443
D
A technician was called to check an unexpected clicking noise on a desktop that has become more frequent every time a video editing application is loaded. The system fans have been replaced, but the clicking noise remains. Diagnostics have been run on the video card.Which of the following should the technician do FIRST? A. Replace the hard drive. B. Replace the video card. C. Do a System Restore. D. Perform a full data backup. E. Scan the system for viruses.
AB
A user accidentally spills liquid on a laptop. The user wants the device to be fixed and would like to know how much it will cost.Which of the following steps should the technician take NEXT to verify if the device is repairable before committing to a price? (Choose two.) A. Remove the case and organize the parts. B. Document the screw locations. C. Search the Internet for repair tutorials. D. Consult colleagues for advice. E. Place the device in rice for a few days.
A
A user brings in a smartphone for repair. The device is unable to send/receive calls or connect to WiFi. All applications on the device are working unless they require connectivity.Which of the following is MOST likely causing the problem? A. Airplane mode B. Tethering C. Disabled hotspot D. VPN
B
A user is experiencing email problems and explains to a technician that all emails with graphics or images do not display the graphics.Which of the following configurations would correct this behavior? A. Change the email settings in antivirus. B. Change the security settings of the email client. C. Change the firewall security settings. D. Change the email proxy settings. E. Change the trusted sites in the browser settings.
B
A user is having a problem with printing a specific document type.The network printer OCP shows that the printer is online with no errors. Other users are not having the same issue. The user sends the document to another printer and the document prints.Which of the following should a technician do FIRST in troubleshooting the problem? A. Stop and restart the PC print spooler service. B. Verify the user is sending the document to the correct printer queue. C. Have each user send the same document to the correct printer queue. D. Stop and restart the print server queues, and then have the user resend the document.
B
A user is no longer able to browse the Internet after returning from vacation. The user is able to log in and navigate to the local intranet, but not to any outside sites. A technician pings a well-known website by name but gets no reply. The technician then pings its IP address and gets a reply.Which of the following commands will MOST likely resolve the issue? A. ipconfig /all B. ipconfig /flushdns C. ipconfig /release D. ipconfig /setclassid
B
A user logs on a PC and receives a message stating there is a duplicate IP address on the network. After a system restart, the user notices the same error.Which of the following is the MOST probable cause of the error? A. The user is still logged into another device. B. The user has set a static IP address. C. The user has moved to a different office. D. The user has wireless and wired connections.
AD
A user printed several documents to a shared network copier and noticed that they have very faint color density. A technician investigates the issue and verifies that the printer had a maintenance kit installed recently. Which of the following next steps will MOST likely resolve the issue? (Choose two.) A. Replace the toner cartridges B. Replace the fuser module C. Clean the paper tray rollers D. Adjust the printer settings E. Replace the developer F. Empty the waste toner bottles
D
A user purchases a wireless printer and sets it up in an office. The user installs all necessary software for the printer on the computer and connects the printer to the guest wireless network. However, when the user attempts to print to the printer, nothing happens.Which of the following will resolve the issue? A. Set up the userג€™s computer to act as a print server. B. Configure the printer to use the Internet printing protocol. C. Ensure the userג€™s computer is set to DHCP. D. Connect the printer to the company wireless network.
A
A user reports that a laptop is not connecting to the corporate wireless network. A technician confirms with a smartphone that the corporate wireless network is available and can be accessed. The technician observes that the Ethernet connection to the corporate network is working. The technician disconnects theEthernet cable.Which of the following should the technician do NEXT to troubleshoot this problem? A. Confirm that the laptop wireless card is turned on. B. Confirm that the laptop is in range for the access point. C. Confirm that the correct wireless network is selected. D. Confirm the userג€™s network login ID and password.
A
A user reports that printing on heavy cardstock paper results in the image smearing if touched. When printing on plain paper, the problem does not occur.Which of the following would be the NEXT troubleshooting step to perform? A. Increase the fuser temperature. B. Change the paper feed rate. C. Clean the transfer roller. D. Replace the toner cartridge.
A
A user sets up a cable modem at home and connects the modem to the ISP at the cable company. Which of the following network types does this connection describe? A. WAN B. LAN C. PAN D. MAN
A
A user wants to build a computer with a high-end CPU, plenty of RAM, and a high-end graphics card for online gaming. The user wants to verify that the graphics card is compatible with the motherboard. Which of the following connection types would the user MOST likely utilize to connect the video card to the motherboard? A. PCle B. ISA C. AGP D. USB
D
A userג€™s laptop is shutting down unexpectedly. The technician discovers the shutdowns only happen when the laptop is moved from one room to another. The technician reseated the hard drive, memory, battery, and LCD cable, but the laptop continues to shut down.Which of the following is the MOST probable cause of the issue? A. Residual energy on the motherboard B. System overheating C. Distended capacitors D. Loose battery connection E. CMOS battery failure
A
A workstation was just moved to a new work location without a surge protector. It was working the day before, but now the PC will not power on, the fans will not spin, and there are no signs of activity. Which of the following should the technician do FIRST? A. Check the power cable connection B. Check the voltage of the PSU with a tester C. Test for distended capacitors D. Check the voltage switch
A
An ISP has notified a SOHO user of a usage increase on the userג€™s network. The user is concerned the WiFi network is being utilized by unauthorized users.Which of the following would minimize the unauthorized use of the WiFi network? A. Implement MAC filtering B. Enable NAT C. Create a network DMZ D. Upgrade the encryption standards
B
An analyst asks a technician to recommend a solution for a customer in the software development industry, where the customer can test a variety of OSs running the various applications that the customer produces. The customer wants to minimize the investment in hardware.Which of the following solutions should the technician recommend to BEST meet the customerג€™s requirement? A. Purchase a number of low-cost devices, installing the required OSs and applications on each one. Use separate machines for each testing environment. B. Purchase a high-end system meeting the hardware requirements for all of the individual OSs and applications. Configure a VM for each testing environment. C. Purchase one computer and create images for each computer configuration and OS. Re-image the machine for each testing environment. D. Purchase a number of computers, installing a VM on each one. Configure each VM with an OS for the testing environment.
A
An associate is seeking advice on which device to purchase for a friend who is a business owner. The friend needs the ability to chart activity while keeping in contact with the home office.Which of the following would be the BEST recommendation? A. Smart watch B. Fitness monitor C. Global positioning sensor D. Portable hotspot
C
An end user wants to have a second monitor installed on a laptop. Which of the following would allow a technician to configure the laptop to show both screens once the cable is connected? A. Plug an external monitor into the USB port. B. Use the Fn and function key combination C. Adjust the monitor display settings. D. Enable DisplayPort.
A
An engineer is working at a remote site that does not have Internet access. Which of the following features should the engineer use to connect a laptop to theInternet if hotspot functionality is unavailable? A. Tethering B. Near field communication C. Wireless LAN D. Virtual private network
B
Ann, a user, needs to attend several day-long conferences and wants to ensure her mobile device will have enough power for these events. She is concerned about wall outlet availability at the conferences and needs to continuously use her device for important updates.Which of the following should a technician recommend to BEST accommodate Annג€™s needs? A. Wireless charging pad B. Built-in battery case C. Extra charging cords D. Airplane mode
B
Ann, an accountant, reports that after turning on her new laptop, she received a message stating her IP address is already in use on the system. She tried going back to her old desktop, which she now only uses for email, but received the same message. The technician checks the account and sees a comment that Ann requires a special network setup to connect to the banking software. Which of the following should the technician do to resolve the issue? A. Remove the static IP configuration from the desktop. B. Set the laptop configuration to DHCP to prevent conflicts. C. Replace the network card in the laptop, as it may be defective. D. Bridge the LAN connection between the laptop and the desktop.
A
During an inspection, it was found that data racks were not properly grounded. To pass the inspection and address a growing concern to protect data cabling and equipment, a technician must make sure all racks are properly grounded.Which of the following tools should the technician use to verify this has been completed? A. Multimeter B. Cable tester C. Tone generator D. Voltmeter
ipconfig/flushdns
IP address of COmputer 1 is changed. Now user can't connect to file shares. What command to use?
A
In a virtual environment, which of the following allows all the VMs to have RAM allocated for use? A. Resource pooling B. Measured service C. Virtual application streaming D. Synchronization
A
Joe, a user, has purchased a new mobile device that uses a different OS than his previous one. Joe wants to copy his contacts and appointments from his corporate account without entering them manually.Which of the following would be the BEST way for a technician to assist Joe? A. Log into the same email provider on the new device, and restore the contacts and dates. B. Create a Bluetooth connection between Joeג€™s devices, and copy his contacts and calendar. C. Back up the old mobile device to a PC, and import the contacts and schedule from the PC. D. Use NFC to transfer all compatible data from one device to the other.
D
Multiple users report that the network printer, which is connected through the print server, is not printing.Which of the following should a technician do FIRST to remedy this situation? A. Replace the USB cable. B. Reinstall the drivers on usersג€™ PCs. C. Have users restart their PCs. D. Clear the print queue.
A
Several company users are frequently forgetting passwords for their mobile devices and applications.Which of the following should the systems administrator do to reduce the number of help desk tickets submitted? A. Implement single sign-on. B. Enable multifactor authentication. C. Configure biometric authentication. D. Remove complex password requirements.
D
Several computers are having network connectivity issues. Two of the computers are wired and are not having any issues. The technician verifies that none of the computers having issues have been assigned a static IP.Which of the following should the technician check NEXT? A. Check the closest AP for the area. B. Check each wireless adapter switch. C. Check the groupג€™s network switch. D. Check the DHCP server.
A
The ability for new computers to be automatically connected to the network is provided by the: A. DHCP server B. DNS server C. proxy server D. TACACS server
A
The cloud model that represents a company maintaining some data in on-premise storage and some data in cloud-based storage is known as: A. hybrid B. private C. public D. community
A
The feature that allows users to store files in cloud-based storage when necessary, but can be removed when space is freed up, is known as: A. on-demand B. resource pool C. synchronization application D. shared resources
D
The touch-screen feature on a Windows device has stopped working.Which of the following should the technician check FIRST? A. Device Manager B. Performance Monitor C. System configuration D. Digitizer settings
C
Whenever a userג€™s machine is turned on, a black screen appears prompting the user for an administrative password. The technician has no such password on file for this machine.Which of the following steps should the technician take to resolve this issue? A. Press and hold the CPU power button for five seconds, and then power back on. B. Disconnect and reconnect the internal hard drive. C. Remove the CMOS battery and reinsert it after ten seconds. D. Remove the motherboard and place it back into the machine after ten minutes.
C
Which of the following Ethernet cables would BEST support an application that requires a 600Mbps throughput at the lowest price point? A. Cat 3 B. Cat 5 C. Cat 5e D. Cat 6
B
Which of the following Internet connection types often terminates at a switching center and then requires the use of a different media for the last mile to the customer? A. ISDN B. DSL C. Fiber D. Cable
A
Which of the following channels would commonly be used on an 802.11 wireless network? A. 6 B. 17 C. 802 D. 8080
D
Which of the following charging and data ports has a non-directional connector? A. Micro-USB B. Mini-USB C. USB-A D. USB-C
C
Which of the following cloud computing concepts allows scalable services to be provided to the client? A. On-demand B. Metered C. Rapid elasticity D. Resource pooling
B
Which of the following connector types is used to terminate household telephone cabling? A. RG-6 B. RJ-11 C. RJ-45 D. RG-59
B
Which of the following devices can be used to connect multiple devices within a network without broadcasting to every network port? A. Unmanaged switch B. Hub C. Firewall D. Cable modem
A
Which of the following devices is used to implement network security policies for an environment? A. Firewall B. Managed switch C. Repeater D. Gateway
DE
Which of the following features will save the battery life of a laptop significantly if they are disabled? (Choose two.) A. Touchpad B. Volume C. Screen orientation D. Cellular E. Bluetooth F. Fingerprint reader
D
Which of the following is designed to function BEST in harsh lighting conditions? A. Large tablet B. E-reader C. Smart watch D. Virtual reality headset
A
Which of the following is the MOST likely cause for a network PC to have an APIPA address? A. DHCP failure B. DNS resolution C. Duplicate IP address D. Cleared ARP cache
A
Which of the following is the main purpose of the +5VSB output of a power supply? A. It allows peripherals to draw power when the machine is off B. It provides power to the audio and sound boards of the machine C. It acts as the main voltage supply to the motherboard and processor D. It powers all expansion cards and external device hubs
B
Which of the following peripheral types is MOST likely to be used to input actions into a PC? A. Webcam B. Mouse C. Monitor D. Optical drive
AC
Which of the following peripherals would a company use to take inventory quickly and update price tags for products? (Choose two.) A. Barcode scanner B. Label printer C. Magnetic reader D. KVM switch E. NFC device F. Flatbed scanner
AF
Which of the following ports are used for secure sessions? (Choose two.) A. 22 B. 23 C. 25 D. 80 E. 110 F. 443
B
Which of the following resources is the MOST critical when using cloud file-storage synchronization applications? A. Disk speed B. I/O bandwidth C. RAM utilization D. CPU utilization
A
Which of the following services provides the ability to resolve UNC to appropriate IP addresses? A. DNS B. DHCP C. Proxy D. Web server
A
Which of the following technologies can be used for wireless payments? A. NFC B. Bluetooth C. IR D. LTE
C
Which of the following terminates a coaxial cable? A. DB9 B. RJ45 C. RG-59 D. RS-232
A
Which of the following wireless standards is only capable of 5GHz frequencies? A. 802.11a B. 802.11ac C. 802.11b D. 802.11g
