Networking Module 3

extended

What type of ACL offers greater flexibility and control over network access? numbered standard named standard extended flexible

private

What type of address is 10.100.126.126? private public

private

What type of address is 10.100.34.34? private public

Private

What type of address is 10.131.48.7? Private Public

private

What type of address is 10.19.6.7? private public

Public

What type of address is 128.107.240.239? Public Private

Private

What type of address is 192.168.7.126? Private Public

Public

What type of address is 198.133.219.148? Private. Public

public

What type of address is 64.100.190.189? public private

public

What type of address is 64.101.198.107 public private

public

What type of address is 64.101.198.197? public private

0.3.255.255

What wild card mask will match networks 172.16.0.0 through 172.19.0.0? 0.0.3.255 0.252.255.255 0.3.255.255 0.0.255.255

Router(config)# access-list 95 permit any Router(config)# access-list 95 deny 172.16.0.0 0.0.255.255

A network administrator is writing a standard ACL that will deny any traffic from the 172.16.0.0/16 network, but permit all other traffic. Which two commands should be used? (Choose two.) Router(config)# access-list 95 deny 172.16.0.0 255.255.0.0 Router(config)# access-list 95 permit any Router(config)# access-list 95 host 172.16.0.0 Router(config)# access-list 95 deny 172.16.0.0 0.0.255.255 Router(config)# access-list 95 172.16.0.0 255.255.255.255 Router(config)# access-list 95 deny any

Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.0 Router1(config)# access-list 10 permit host 192.168.15.23

A network administrator needs to configure a standard ACL so that only the workstation of the administrator with the IP address 192.168.15.23 can access the virtual terminal of the main router. Which two configuration commands can achieve the task? (Choose two.) Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.0 Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.255 Router1(config)# access-list 10 permit 192.168.15.23 255.255.255.255 Router1(config)# access-list 10 permit host 192.168.15.23 Router1(config)# access-list 10 permit 192.168.15.23 255.255.255.0

to apply an extended ACL to an interface

A technician is tasked with using ACLs to secure a router. When would the technician use the 'ip access-group 101 in' configuration option or command? to apply an extended ACL to an interface to secure management traffic into the router to secure administrative access to the router to display all restricted traffic

to create an entry in a numbered ACL

A technician is tasked with using ACLs to secure a router. When would the technician use the 40 deny host 192.168.23.8 configuration option or command? to remove all ACLs from the router to create an entry in a numbered ACL to apply an ACL to all router interfaces to secure administrative access to the router

to secure administrative access to the router

A technician is tasked with using ACLs to secure a router. When would the technician use the access-class 20 in configuration option or command? to secure administrative access to the router to remove an ACL from an interface to remove a configured ACL to apply a standard ACL to an interface

to identify any IP address

A technician is tasked with using ACLs to secure a router. When would the technician use the any configuration option or command? to add a text entry for documentation purposes to generate and send an informational message whenever the ACE is matched to identify any IP address to identify one specific IP address

to restrict specific traffic access through an interface

A technician is tasked with using ACLs to secure a router. When would the technician use the deny configuration option or command? to identify one specific IP address to display all restricted traffic to restrict specific traffic access through an interface to generate and send an informational message whenever the ACE is matched

to allow returning reply traffic to enter the internal network

A technician is tasked with using ACLs to secure a router. When would the technician use the established configuration option or command? to add a text entry for documentation purposes to display all restricted traffic to allow specified traffic through an interface to allow returning reply traffic to enter the internal network

to identify one specific IP address

A technician is tasked with using ACLs to secure a router. When would the technician use the host configuration option or command? to add a text entry for documentation purposes to generate and send an informational message whenever the ACE is matched to identify any IP address to identify one specific IP address

to apply an extended ACL to an interface

A technician is tasked with using ACLs to secure a router. When would the technician use the ip access-group 101 in configuration option or command? to secure administrative access to the router to apply an extended ACL to an interface to display all restricted traffic to secure management traffic into the router

to remove a configured ACL

A technician is tasked with using ACLs to secure a router. When would the technician use the no ip access-list 101 configuration option or command? to apply an ACL to all router interfaces to secure administrative access to the router to remove all ACLs from the router to remove a configured ACL

to add a text entry for documentation purposes

A technician is tasked with using ACLs to secure a router. When would the technician use the remark configuration option or command? to generate and send an informational message whenever the ACE is matched to add a text entry for documentation purposes to identify one specific IP address to restrict specific traffic access through an interface

A Telnet or SSH session is allowed from any device on the 192.168.10.0 into the router with this access list assigned. Devices on the 192.168.10.0/24 network are allowed to reply to any ping requests.

Consider the following access list. access-list 100 permit ip host 192.168.10.1 anyaccess-list 100 deny icmp 192.168.10.0 0.0.0.255 any echoaccess-list 100 permit ip any any Which two actions are taken if the access list is placed inbound on a router Gigabit Ethernet port that has the IP address 192.168.10.254 assigned? (Choose two.) Only Layer 3 connections are allowed to be made from the router to any other network device. Devices on the 192.168.10.0/24 network are not allowed to reply to any ping requests. Devices on the 192.168.10.0/24 network can sucessfully ping devices on the 192.168.11.0 network. A Telnet or SSH session is allowed from any device on the 192.168.10.0 into the router with this access list assigned. Devices on the 192.168.10.0/24 network are allowed to reply to any ping requests. Only the network device assigned the IP address 192.168.10.1 is allowed to access the router

An SSH connection is allowed from a workstation with IP 192.168.25.18 to a device with IP 172.16.45.16.

Refer to the exhibit. A network administrator configures an ACL on the router. Which statement describes the result of the configuration? An SSH connection is allowed from a workstation with IP 172.16.45.16 to a device with IP 192.168.25.18. An SSH connection is allowed from a workstation with IP 192.168.25.18 to a device with IP 172.16.45.16. A Telnet connection is allowed from a workstation with IP 192.168.25.18 to a device with IP 172.16.45.16. A Telnet connection is allowed from a workstation with IP 172.16.45.16 to a device with IP 192.168.25.18.

The sequence of the ACEs is incorrect.

Refer to the exhibit. A network administrator has configured ACL 9 as shown. Users on the 172.31.1.0 /24 network cannot forward traffic through router CiscoVille. What is the most likely cause of the traffic failure? The established keyword is not specified. The sequence of the ACEs is incorrect. The port number for the traffic has not been identified with the eq keyword. The permit statement specifies an incorrect wildcard mask.

ACL 10 is removed from the running configuration.

Refer to the exhibit. A network administrator is configuring a standard IPv4 ACL. What is the effect after the command no access-list 10 is entered? ACL 10 is removed from both the running configuration and the interface Fa0/1. ACL 10 is removed from the running configuration. ACL 10 is disabled on Fa0/1. ACL 10 will be disabled and removed after R1 restarts.

5 deny 172.23.16.0 0.0.15.255

Refer to the exhibit. A network administrator needs to add an ACE to the TRAFFIC-CONTROL ACL that will deny IP traffic from the subnet 172.23.16.0/20. Which ACE will meet this requirement? 30 deny 172.23.16.0 0.0.15.255 15 deny 172.23.16.0 0.0.15.255 5 deny 172.23.16.0 0.0.15.255 5 deny 172.23.16.0 0.0.255.255

R2(config-if)# ip access-group 101 in R2(config)# interface fastethernet 0/0 R2(config)# access-list 101 permit ip host 192.168.1.1 host 192.168.2.1

Refer to the exhibit. A network administrator wants to permit only host 192.168.1.1 /24 to be able to access the server 192.168.2.1 /24. Which three commands will achieve this using best ACL placement practices? (Choose three.) R2(config)# interface fastethernet 0/1 R2(config-if)# ip access-group 101 out R2(config)# access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 R2(config-if)# ip access-group 101 in R2(config)# access-list 101 permit ip any any R2(config)# interface fastethernet 0/0 R2(config)# access-list 101 permit ip host 192.168.1.1 host 192.168.2.1

The ACL is implicitly denying access to all the servers.

Refer to the exhibit. A new network policy requires an ACL denying FTP and Telnet access to a Corp file server from all interns. The address of the file server is 172.16.1.15 and all interns are assigned addresses in the 172.18.200.0/24 network. After implementing the ACL, no one in the Corp network can access any of the servers. What is the problem? Inbound ACLs must be routed before they are processed. The ACL is implicitly denying access to all the servers. Named ACLs require the use of port numbers. The ACL is applied to the interface using the wrong direction

All traffic will be blocked, not just traffic from the 172.16.4.0/24 subnet.

Refer to the exhibit. An ACL was configured on R1 with the intention of denying traffic from subnet 172.16.4.0/24 into subnet 172.16.3.0/24. All other traffic into subnet 172.16.3.0/24 should be permitted. This standard ACL was then applied outbound on interface Fa0/0. Which conclusion can be drawn from this configuration?​ The ACL should be applied outbound on all interfaces of R1. The ACL should be applied to the FastEthernet 0/0 interface of R1 inbound to accomplish the requirements. All traffic will be blocked, not just traffic from the 172.16.4.0/24 subnet. Only traffic from the 172.16.4.0/24 subnet is blocked, and all other traffic is allowed.​ An extended ACL must be used in this situation.

Ping packets will be permitted. SSH packets will be permitted.

Refer to the exhibit. An administrator first configured an extended ACL as shown by the output of the show access-lists command. The administrator then edited this access-list by issuing the commands below. Router(config)# ip access-list extended 101 Router(config-ext-nacl)# no 20 Router(config-ext-nacl)# 5 permit tcp any any eq 22 Router(config-ext-nacl)# 20 deny udp any any Which two conclusions can be drawn from this new configuration?​ (Choose two.) TFTP packets will be permitted.​ Ping packets will be permitted. Telnet packets will be permitted. SSH packets will be permitted. All TCP and UDP packets will be denied

The traffic is dropped.

Refer to the exhibit. An administrator has configured a standard ACL on R1 and applied it to interface serial 0/0/0 in the outbound direction. What happens to traffic leaving interface serial 0/0/0 that does not match the configured ACL statements? The traffic is dropped. The source IP address is checked and, if a match is not found, traffic is routed out interface serial 0/0/1. The resulting action is determined by the destination IP address. The resulting action is determined by the destination IP address and port number.

standard ACL inbound on R1 G0/1

Refer to the exhibit. Employees on 192.168.11.0/24 work on critically sensitive information and are not allowed access off their network. What is the best ACL type and placement to use in this situation? standard ACL inbound on R1 vty lines extended ACL inbound on R1 G0/0 standard ACL inbound on R1 G0/1 extended ACL inbound on R3 S0/0/1

standard ACL outbound on R2 WAN interface towards the internet

Refer to the exhibit. Internet privileges for an employee have been revoked because of abuse but the employee still needs access to company resources. What is the best ACL type and placement to use in this situation? standard ACL inbound on R2 WAN interface connecting to the internet standard ACL outbound on R2 WAN interface towards the internet standard ACL inbound on R1 G0/0 standard ACL outbound on R1 G0/0

extended ACLs inbound on R1 G0/0 and G0/1

Refer to the exhibit. Many employees are wasting company time accessing social media on their work computers. The company wants to stop this access. What is the best ACL type and placement to use in this situation? extended ACL outbound on R2 WAN interface towards the internet standard ACL outbound on R2 WAN interface towards the internet standard ACL outbound on R2 S0/0/0 extended ACLs inbound on R1 G0/0 and G0/1

extended ACL inbound on R3 G0/0

Refer to the exhibit. Network 192.168.30.0/24 contains all of the company servers. Policy dictates that traffic from the servers to both networks 192.168.10.0 and 192.168.11.0 be limited to replies for original requests. What is the best ACL type and placement to use in this situation? extended ACL inbound on R3 G0/0 extended ACL inbound on R1 G0/0 standard ACL inbound on R1 G0/1 standard ACL inbound on R1 vty lines

extended ACL inbound on R2 WAN interface connected to the internet

Refer to the exhibit. Only authorized remote users are allowed remote access to the company server 192.168.30.10. What is the best ACL type and placement to use in this situation? extended ACLs inbound on R1 G0/0 and G0/1 extended ACL outbound on R2 WAN interface towards the internet extended ACL inbound on R2 S0/0/0 extended ACL inbound on R2 WAN interface connected to the internet

R1 Gi0/1.12 outbound

Refer to the exhibit. The Gigabit interfaces on both routers have been configured with subinterface numbers that match the VLAN numbers connected to them. PCs on VLAN 10 should be able to print to the P1 printer on VLAN 12. PCs on VLAN 20 should print to the printers on VLAN 22. What interface and in what direction should you place a standard ACL that allows printing to P1 from data VLAN 10, but stops the PCs on VLAN 20 from using the P1 printer? (Choose two.) inbound R2 S0/0/1 R1 Gi0/1.12 outbound R1 S0/0/0 R2 Gi0/1.20

extended ACL outbound on R2 WAN interface towards the internet

Refer to the exhibit. The company CEO demands that one ACL be created to permit email traffic to the internet and deny FTP access. What is the best ACL type and placement to use in this situation? extended ACL outbound on R2 WAN interface towards the internet standard ACL outbound on R2 S0/0/0 extended ACL inbound on R2 S0/0/0 standard ACL inbound on R2 WAN interface connecting to the internet

extended ACL inbound on R1 G0/0

Refer to the exhibit. The company has provided IP phones to employees on the 192.168.10.0/24 network and the voice traffic will need priority over data traffic. What is the best ACL type and placement to use in this situation? extended ACL inbound on R1 G0/0 extended ACL outbound on R2 WAN interface towards the internet extended ACL outbound on R2 S0/0/1 extended ACLs inbound on R1 G0/0 and G0/1

The commands are added at the end of the existing Managers ACL.

Refer to the exhibit. The named ACL "Managers" already exists on the router. What will happen when the network administrator issues the commands that are shown in the exhibit? The commands are added at the end of the existing Managers ACL. The commands overwrite the existing Managers ACL. The commands are added at the beginning of the existing Managers ACL. The network administrator receives an error that states that the ACL already exists.

standard ACL inbound on R1 vty lines

Refer to the exhibit. The network administrator has an IP address of 192.168.11.10 and needs access to manage R1. What is the best ACL type and placement to use in this situation? extended ACL outbound on R2 WAN interface towards the internet standard ACL inbound on R1 vty lines extended ACLs inbound on R1 G0/0 and G0/1 extended ACL outbound on R2 S0/0/1

Apply an inbound extended ACL on R1 Gi0/0.

Refer to the exhibit. The student on the H1 computer continues to launch an extended ping with expanded packets at the student on the H2 computer. The school network administrator wants to stop this behavior, but still allow both students access to web-based computer assignments. What would be the best plan for the network administrator? Apply an inbound standard ACL on R1 Gi0/0. Apply an inbound extended ACL on R2 Gi0/1. Apply an outbound extended ACL on R1 S0/0/1. Apply an inbound extended ACL on R1 Gi0/0. Apply an outbound standard ACL on R2 S0/0/1

The router has not had any Telnet packets from 10.35.80.22 that are destined for 10.23.77.101.

Refer to the exhibit. What can be determined from this output? The ACL is missing the deny ip any any ACE. The ACL is only monitoring traffic destined for 10.23.77.101 from three specific hosts. Because there are no matches for line 10, the ACL is not working. The router has not had any Telnet packets from 10.35.80.22 that are destined for 10.23.77.101.

access-list 1 permit 192.168.10.96 0.0.0.31

Refer to the exhibit. Which command would be used in a standard ACL to allow only devices on the network attached to R2 G0/0 interface to access the networks attached to R1? access-list 1 permit 192.168.10.128 0.0.0.63 access-list 1 permit 192.168.10.0 0.0.0.255 access-list 1 permit 192.168.10.96 0.0.0.31 access-list 1 permit 192.168.10.0 0.0.0.63

access-list 1 permit 192.168.10.0 0.0.0.127 access-list 5 permit 192.168.10.0 0.0.0.63 access-list 5 permit 192.168.10.64 0.0.0.63

Refer to the exhibit. Which two ACLs would permit only the two LAN networks attached to R1 to access the network that connects to R2 G0/1 interface? (Choose two.) access-list 1 permit 192.168.10.0 0.0.0.127 access-list 2 permit host 192.168.10.9 access-list 2 permit host 192.168.10.69 access-list 5 permit 192.168.10.0 0.0.0.63 access-list 5 permit 192.168.10.64 0.0.0.63 access-list 3 permit 192.168.10.128 0.0.0.63 access-list 4 permit 192.168.10.0 0.0.0.255

Router(config-std-nacl)#

What does the CLI prompt change to after entering the command ip access-list standard aaa from global configuration mode? Router(config-line)# Router(config-std-nacl)# Router(config)# Router(config-router)# Router(config-if)#

Traffic originating from 172.16.4.0/24 is permitted to all TCP port 80 destinations.

What effect would the Router1(config-ext-nacl)# permit tcp 172.16.4.0 0.0.0.255 any eq www command have when implemented inbound on the f0/0 interface? All TCP traffic is permitted, and all other traffic is denied. Traffic originating from 172.16.4.0/24 is permitted to all TCP port 80 destinations. All traffic from 172.16.4.0/24 is permitted anywhere on any port. The command is rejected by the router because it is incomplete.

Place identical restrictions on all vty lines.

What is considered a best practice when configuring ACLs on vty lines? Place identical restrictions on all vty lines. Remove the vty password since the ACL restricts access to trusted users. Apply the ip access-group command inbound. Use only extended access lists.

Use the no keyword and the sequence number of the ACE to be removed.

What is the quickest way to remove a single ACE from a named ACL? Use the no keyword and the sequence number of the ACE to be removed. Copy the ACL into a text editor, remove the ACE, then copy the ACL back into the router. Create a new ACL with a different number and apply the new ACL to the router interface. Use the no access-list command to remove the entire ACL, then recreate it without the ACE.

access-list 101 permit tcp any host 192.168.1.1 eq 80

Which ACE will permit a packet that originates from any network and is destined for a web server at 192.168.1.1? access-list 101 permit tcp any host 192.168.1.1 eq 80 access-list 101 permit tcp host 192.168.1.1 eq 80 any access-list 101 permit tcp host 192.168.1.1 any eq 80 access-list 101 permit tcp any eq 80 host 192.168.1.1

access-list 103 permit tcp 192.168.10.0 0.0.0.255 host 172.17.80.1 eq 80 access-list 103 deny tcp ​192.168.10.0 0.0.0.255 any eq 23

Which set of access control entries would allow all users on the 192.168.10.0/24 network to access a web server that is located at 172.17.80.1, but would not allow them to use Telnet? access-list 103 deny tcp host 192.168.10.0 any eq 23 access-list 103 permit tcp host 192.168.10.1 eq 80 access-list 103 permit tcp 192.168.10.0 0.0.0.255 any eq 80 access-list 103 deny tcp 192.168.10.0 0.0.0.255 any eq 23 access-list 103 permit 192.168.10.0 0.0.0.255 host 172.17.80.1 access-list 103 deny tcp 192.168.10.0 0.0.0.255 any eq telnet​​ access-list 103 permit tcp 192.168.10.0 0.0.0.255 host 172.17.80.1 eq 80 access-list 103 deny tcp ​192.168.10.0 0.0.0.255 any eq 23

They filter traffic based on source IP addresses only.

Which statement describes a characteristic of standard IPv4 ACLs? They are configured in the interface configuration mode. They can be configured to filter traffic based on both source IP addresses and source ports. They can be created with a number but not with a name. They filter traffic based on source IP addresses only.

Inbound ACLs are processed before the packets are routed while outbound ACLs are processed after the routing is completed.

Which statement describes a difference between the operation of inbound and outbound ACLs? Inbound ACLs are processed before the packets are routed while outbound ACLs are processed after the routing is completed. In contrast to outbound ALCs, inbound ACLs can be used to filter packets with multiple criteria. On a network interface, more than one inbound ACL can be configured but only one outbound ACL can be configured. Inbound ACLs can be used in both routers and switches but outbound ACLs can be used only on routers.

host any

Which two keywords can be used in an access control list to replace a wildcard mask or address and wildcard mask pair? (Choose two.) host most gt some any all

destination UDP port number ICMP message type

Which two packet filters could a network administrator use on an IPv4 extended ACL? (Choose two.) destination UDP port number computer type destination MAC address ICMP message type source TCP hello address