Testout Network Pro Ch 1-8 Exams and Labs
Which of the following terms are often synonymous with or made possible with CIDR? (2)
-Classless -VLSM
Which of the following devices operate at OSI Model layer 2? (Select two)
-Network Interface Card -Switch
Which of the following connectors usually require polishing as part of the assembly process? (Select two.)
-ST -SC
Which port number is used by SNMP
161
Which of the following is a characteristic of static routing when compared to dynamic routing?
All routers must be manually updated on the router.
Which of the following describes how access lists
An access list filters traffic based on the IP header information such as source or destination IP address, protocol, or socket numbers.
Which type of polish grade uses green-colored connectors to help prevent using the wrong connector type?
Angled Physical Contact
You provide Internet access for a local school
Application Level
You are working with an older 10Base2 Ethernet network. Which of the following connector types will you most likely encounter?
BNC
Which of the following is a valid MAC address? 34-9A-86-1G-B3-24 83-5A-5B-0B-31-55-F1 255.255.255.0 C0-34-FF-15-01-8E 73-99-12-61-15 192-168-12-15
C0-34-FF-15-01-8E
The media access control method of all Ethernet networks is
CSMA/CD
Which of the following cable types often includes a solid plastic core?
Cat 6
You manage a network that uses 1000BaseT Ethernet. You find that one device communicates on the network at only 100 Mbps. Which tool should you use to test the drop cable and the connection to the network?
Certifier
You have implemented a network where hosts are assigned specific roles, such as for file sharing and printing. Other hosts access those resources but do not host services of their own. What type of network do you have?
Client-server
when designing a firewall, what is the recommended approach
Close all ports, open only ports required
You have just connected four switches as shown in the Exhibit. Assuming the default switch configuration, how can your force Switch C to become a root bridge?
Configure a priority number of 4096 for switch C
You have three switches configured as shown in the Exhibit. How can you guarantee that switch C becomes the root bridge?
Configure switch C with a lower priority value
What does the ip address dhcp command allow you to do?
Configures the switch to obtain an IP address from a DHCP server.
Which of the following prevents access based on website rating and classifications?
Content filter
Which of the following prevents access based on website ratings
Content filter
You are building network cables and attaching RJ45 connectors to each end. Which tool do you need for this task?
Crimping Tool
Your company purchase a new bridge, which filters packets based on the MAC address of the destination computer. On which layer of the OSI Model is this device functioning?
Data Link
Which of the following describes the point where the service provider's responsibility ends and the customer's responsibility for installing and maintaining wiring and equipment?
Demarc
Using the Netstat command, you notice that a remote system
Downloading a file
Which of the following routing protocols is classified as a balance hybrid routing protocol?
EIGRP
You have a cable Internet connection at home. The installer had connected the router near the outside wall of your house with RG-6 cable. You move the cable router a distance of 50 meters using RG-8 cables and special connector adapters. Which condition are you most likely to experience?
Echo
You manage a network with multiple switches. You find that your switches are experiencing heavy broadcast storms. Which of the following will help reduce the effects of a broadcast storm?
Enable spanning tree on the switches
You have two switches connected as shown in the Exhibit. You would like to configure rapid spanning tree on switch A. On which ports would you use portfast command?
Fa0/1 and Fa0/2
You are the network administrator for a small organization. Recently, you contracted with an ISP to connect your organization's network to the Internet to provide users with Internet access. Since doing so, it has come to your attention that an intruder has invaded your network from the Internet on three separate occasions. Router Switch Hub CSU/DSU Proxy server Firewall
Firewall
Which protocol is used on the World Wide Web to transmit Web pages to Web browsers
HTTP
Which protocol is used for securely browsing a website?
HTTPS
You have a network that occupies both floors of a building. The WAN service provider has installed the line for the WAN service into the building in a wiring closet on the main floor. You have a second wiring closet on the second floor directly above the wiring closed that holds the demar. Which of the following describes the closet on the second floor?
IDF
Which of the following protocols stores email on the mail server and gives users a choice to download mail or keep it on the server?
IMAP4
IP address Subnet Mask Default Gateway DNS server
IP: 192.168.12.46 Subnet: 255.255.255.240 Default G: 192.168.12.34 DNS: 198.162.1.22
Under which of the following circumstances might you implement BGP on your company network and share routes with internet routers?
If the network is connected to the internet using multiple ISPs
You manage a local area network with several switches. A new employee has started today so you connect her workstation to a switch port. Which of the following is the most likely cause of the problem?
Incorrect VLAN assignment
Which of the following best describes how a switch functions?
It connects multiple cable segments (or devices), and forwards frames to the appropriate segment.
A switch running STP is in the listening state. A message destined for a different network segment arrives at the switch. Which of the following best describes what the switch will do?
It does not record the address or segment information. It does not forward the message
The UDP transport protocol provides which of the following features?
Low Overhead Connectionless datagram services
Which two of the following tasks do routers perform?
Maintain information about paths through an internetwork. Route data based on logical network addresses.
You have implemented an ad-hoc wireless network that doesn't employ a wireless access point. Every wireless network card can communicate directly with any other wireless network card on the network. What type of physical network topology has been implemented in this type of network?
Mesh
You want to implement a fault tolerant topology as you interconnect routers on your wide area netowrk. Which of the following would meet your needs?
Mesh
You manage a network of multiple subnets connected to the Internet. A user reports that she can't access the Internet. You investigate the problem and find that she can access all hosts on the private network, but no hosts on the Internet. Which of the following is likely the cause of the problem?
Missing default route on a router.
You want to measure the voltage, amps, and ohms of various devices. Which tool should you use?
Multimeter.
Examine the following output: Active Connections Proto Local Address Foreign Address State TCP SERVER1:1036 localhost:4832 TIME_WAIT TCP SERVER1:4798 localhost:1032 TIME_WAIT TCP SERVER1:1258 pool-141-150-16-231.mad.east.ttr:24076 CLOSE_WAIT TCP SERVER1:2150 cpe-66-67-255-118.roc.res.rr.com:14100 ESTABLISHED TCP SERVER1:268 C872c-032.cpe.net.cale.rers.com:46360 ESTABLISHED TCP SERVER1:2995 ip68-97-96-186.ok.ok.cox.net:23135 ESTABLISHED Which of the following utilities produced this output?
Netstat
Which of the following routing protocols uses relative link cost as a metric?
OSPF
What are the main differences between the OSPF and IS-IS routing protocols?
OSPF requires an area 0, while IS-IS does not.
Which of the following associates a port number with a host on a private network?
PAT
You have been asked to implement a wired network infrastracture that will accommodate fialed conenctions. You don't have a large budget, so you decide to provide redundancy for only a handful of critical devices. Which of the following netowork topologies should you implement?
Partial Mesh
What topology is used with 100BaseTX Fast Ethernet networks?(2 answers)
Physical star/logical bus Physical star/logical star
You are adding new wires in your building for some new offices. The building has a false ceiling that holds the lights. You would like to run your Ethernet cables in this area. Which type of cable must you use?
Plenum
You have just installed a packet-filtering firewall
Port number/source address of a packet/destination address of a packet
Match each layer of the TCP/IP model on the left with the corresponding layer of the OSI model on the right. Each option on the left can be used more then one.
Presentation-Application Data Link-Network Interface Application-Application Session-Application Network-Internet Transport-Transport
What tool should you use to extend network services beyond the demarc?
Punchdown tool
You are working with 25 pair wires and 66 blocks. You have pushed the wires onto the 66 block, but now need to cut off the excess end of each wire. Which tool should you use?
Punchdown tool
You have used firewalls to create a demilitarized zone
Put the Database on the private network/Put the Web server inside the DMZ
You have a small home network connected to the Internet using an RG-6 cable. You need to move the router connecting the network to the Internet, but can't find any RG-6 cable. Which cable types could you use instead?
RG-59
Of the following cables, which offer the best protection against EMI?
RG-6
Which of the following protocols has a limit of 15 hops between and two networks?
RIP
You need to configure spanning tree on a Cisco switch. You'd like to use a protocol that confirms to the 802.1w standards. Which protocol should you use?
Rapid PVST+
Which of the following hardware devices regenerates a signal out all connected ports without examining the frame or packet contents? (Select two)
Repeater Hub
A user from the Sales department calls to report that he is experiencing problems connecting to the Sales file server. All users in the Sales department connect to the Sales server through a single Ethernet switch. No other users have reported problems connecting to the Sales server. Which of the following troubleshooting actions are you most likely to perform first?
Replace the network card in the user's computer.
What is the main difference between RIP and RIPv2?
Rip is a classful protocol, while RIPv2 is a classless protocol.
You have purchased a new router that you need to configure. You need to connect a workstation to the router's console port to complete the configuration task. Which type of cable would you most likely use?
Rollover
Which process reduces the size of the routing table by advertising a single route as a destination for a group of contiguous subnets?
Route summarization
Which of the following features dynamically places switch ports in blocking or forwarding states?
Spanning tree
You need to connect a workstation to a switch using a regular port on the switch (not an uplink port). The switch does not sport auto-MDI. Which type of cable should you use?
Straight-Through
Which of the following are true about routed firewalls
Supports Counts
Users complain that they can't connect to the website when they type
The HTTP port should be changed to 80
You are monitoring network traffic on your network and you see a large amount of traffic between a Windows
The workstation is using NetBIOS to access shared resources on the server
What device sends signals from a computer onto a network? Transceiver Cable Gateway Router
Transceiver
When configuring VLANs on a switch, what type of switch ports are members of all VLANs defined on the switch?
Trunk Ports
Which protocol and port number is used by BOOTP/DHCP?
UDP 67
You have been recently hired to mange a network for a small company. Prior to your arrival, the entire network was migrated from IPv4 to IPv6. Which strategy could you imply to help prevent these issues from occurring?
Use a /127 prefix on the backbone segment.
Which of the following methods would you use to create a crossover cable?
Use the T568A standard on one connector, and the T568B standard on the other connector
How do switches and bridges learn where the devices are located on a network?
When a frame enters a port, the source MAC address is copied from the frame header.
When would you typically use and RJ-11 connector?
When connecting a phone to a phone line
You want to use the T568B standard for adding connectors to your Cat5 cable. Starting with pin 1, which order should you use for the wires within the connector?
White/orange, orange, white/green, blue, white/blue, green, white/brown, brown
Which of the following benefits apply only to creating VLANs with switches and not to segmenting the network with regular switches?
You can create multiple broadcast domains
In which of the following situations might you use an RJ-11 connector?
You want to connect your computer to the Internet with a dial-up connection
An All-in-one security appliance is best
a Remote
Which TCP/IP utility gives you the following output? Interface: 192.168.4.101 on Interface 0x3 Internet Address Physical Address Type 192.168.1.23 00-d1-b6-b7-c2-af dynamic
arp.
Which command would you use on a switch to enable management from a remote network?
ip default-gateway 192.168.10.185
Which TCP/IP utility gives you the following output?
nbtstat -c.
Which of the following connectors is typically used on one end of a rollover cable?
serial
While troubleshooting a problem on a Linux system, you run a utility that generates the following output:
traceroute
A router is connected to network 192.168.1.0/24 and network 192.168.2.0/24. the router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24. The next hop router for network 192.168.3.0 has changed. You need to make the change with the least amount of effort possible. what should you do.
wait for convergence to take place.
Match each decimal value on the left with the corresponding hexadecimal value on the right. Not all decimal values have a corresponding hexadecimal value.
(drop) - (drag) 11 - 17 B - 11 D - 13 F - 15 C - 12 10 - 16
Consider the 850 nm multimode fiber optic cable shown below. How much loss can you expect between the transmitter and the receiver?
-1.2 dB
Which of the following IP addresses have a default subnet mask of 255.255.0.0? (3)
-129.0.0.1 -168.16.5.1 -191.168.2.15
A host on the network has an IP address of 129.11.99.78 using the default subnet mask. How would you identify the address and mask using CIDR notation?
-129.11.99.78/16
Which three of the following IP addresses are Class B addresses? (3)
-132.12.0.0 -190.65.2.0 -129.0.0.0
Which of the following are valid IPv6 addresses?
-141:0:0:0:15:0:0:1 -6384:1319:7700:7631: 446A:5511:8940:2552
Which of the following IP address ranges is reserved for Automatic Private IP addressing?
-169.254.0.1 - 169.254.255.254
You've decided to use a subnet mask of 255.255.192.0 on the 172.17.0.0 network to create four separate subnets. Which network IDs will be assigned to these subnets in this configuration? (2)
-172.17.0.0 -172.17.128.0
Which of the following is a valid IPv4 address? (2)
-2.2.2.2 -172.16.1.26
You have a network that occupies all three floors of a building. The WAN service prodider has installed the line for the WAN service into the building in a wiring closet on the main floor You have a second wiring closet on the main floor. You need to connect the two wiring closets. Which of the following are typically used to connect the two wiring closets? (Select two.)
-25 Pair -Horizontal cross connect
You are configuring the IP address for a host and have been asked to use the address 192.160.99.110/16. What subnet mask value would you use?
-255.255.0.0
What is the network address and subnet mask used by APIPA? (2)
-255.255.0.0 -169.254.0.0
What is the default subnet mask for the IP address 203.111.3.3?
-255.255.255.0
Which of the following tunneling methods is used to sent IPv4 traffic through an IPv6 network?
-4-to-6 tunneling
You are a network technician for a small corporate network. It was recently decided to switch to a new ISP. The network needs to be moved to the new ISP so that the old one can be cancelled. The new ISP has run a fiber optic line directly to back of the fiber patch panel in the basement networking closet, but the NSA device does not have any fiber ports.
-Add the Media Converter to the Basement -Workspace -Move the Ethernet cable from the wall outlet to the Media Converter's Ethernet port -Connect the SC to LC fiber cable to the Media -Converter's LC port -Connect the SC to LC cable to ports 23 and 24 on the fiber patch panel Show Details -Plug in the Media Converter -Confirm the office has an Internet connection Explanation Because the NSA does not have any fiber ports, you need to use a media converter to convert from a fiber optic cable to an Ethernet cable. Most media converters use SFP ports so they can convert multiple form factors. The media converter in this lab already has a fiber SFP module installed. To complete this lab, use the following steps: 1. On the Shelf, expand the Networking Devices category. 2. Drag the Media Converter to the bottom shelf of the rack in the Workspace. 3. Switch to the back view of the rack. 4. Drag the Ethernet cable from the wall outlet to the Ethernet port on the Media Converter. 5. On the Shelf, expand the Cables category. 6. Drag the SC to LC fiber cable to the LC port on the Media Converter. 7. In the Select Connector dialog, select the LC connector. 8. Switch to the front view of the rack. 9. In the Selected Component window, drag the Fiber Optic SC Connector (A) to port 23 on the fiber patch panel. 10. In the Selected Component window, drag the Fiber Optic SC Connector (B) to port 24 on the fiber patch panel. 11. From the Shelf, drag the Power Adapter to the DC power port on the Media Converter. 12. In the Select Connector window, click DC Power Connector. 13. Switch to the back view of the rack. 14. In the Selected Component window, drag the AC Power Adapter connector to an open outlet on the rack UPS. The lights on the Media Converter should turn on. 15. Navigate to any workstation on Floor 1 or Floor 2 and confirm Internet connectivity. 16. Click Done to complete the lab.
Which three of the following devices operate at the Data Link Layer of the OSI Model?
-Bridges -Network Interface Cards -Switches
1. 124.77.8.5 2. 131.11.0.9 3. 190.66.250.10 4. 196.5.89.44 What is the order of classes presented by the IP addresses above?
-Class A, Class B, Class B, Class C
You manage a server that uses an IP address of 192.168.255.188 with a mask of 255.255.0.0. Which of the following describes the address type?
-Classless
You have a TCP/IP network with 50 hosts. There have been inconsistent communication problems between hosts. You run a protocol analyzer and discover that two hosts have the same IP address assigned. Which protocol can you implement on your network to help prevent problems such as this?
-DHCP
You have a network with 50 workstations. You want to automatically configure workstations with the IP address, subnet mask, and default gateway values. Which device should you use?
-DHCP server
You want to implement a protocol on your network that allows computers to find the IP address of a host from a logical name. Which protocol should you implement?
-DNS
You need to enable hosts on your network to find the IP address of logical names such as srv1.myserver.com. Which device would you use?
-DNS server
Which of the following are functions of the MAC sublayer? (Select two)
-Defining a unique hardware address for each device on the network -Letting devices on the network have access to the LAN
Which of the following services automatically creates and deletes host records when an IP address lease is created or released?
-Dynamic DNS
Which of the following is a valid IPv6?
-FEC0::AB:9007
Which organization is responsible for allocating public IP addresses?
-IANA
Which protocol does an IP host use to inform a router that it wants to receive specific multicast frames?
-IGMP
Which two of the following are included as part of the Data Link Layer?
-Identifying physical network device -Controlling how messages are propagated through the network
Which of the following are advantages of using fiber optic cabling for a network, as opposed to other types of cabling? (Select two)
-Immunity to electromagnetic interference -Greater cable distances without a repeater
You recently created a new network segment for Development. Because the hosts are now on a different network segment, they can no longer contact the DHCP server. Both network segments are connected via a Cisco router. Which of the following would be the best action to take in order to fix the problem?
-Implement an IP Helper address on the router
A user reports that he can't browse to a specific website on the Internet. From his computer, you find that a ping test to the web server succeeds. A traceroute test shows 17 hops to the destination web server. What is the most likely cause of problem?
-Incorrect DNS server address
You manage a network that has multiple internal subnets. You connect a workstation to the 192.168.1.0/24 subnet. This workstatoin cannot communicate with any other host on the network. You run ipconfig /all and see the following: Ethernet adapter Local Area Connection: Connection-specific DNS suffix: mydomain.local Description: Broadcom network adpter Physical Address: 00-AA-BB-CC-74-EF DHCP Enabled: No Autoconfiguration Enabled: Yes IPv4 Address: 192.168.1.102(Preferred) Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1 DNS Servers: 192.168.2.20 What is the most likely cause of the problem?
-Incorrect IP address
You manage a network that has multiple internal subnets. You connect a workstation to the 192.168.1.0/24 subnet. This workstation can communicate with some hosts on the private network, but not with other hosts. You run ipconfig/ all and see the following: Ethernet adapter Local Area Connection: Connection-specific DNS suffix: mydomain.local Description: Broadcom network adpter Physical Address: 00-AA-BB-CC-74-EF DHCP Enabled: No Autoconfiguration Enabled: Yes IPv4 Address: 192.168.1.102(Preferred) Subnet Mask: 255.255.255.0 Default Gateway: 192.168.2.1 DNS Servers: 192.168.2.20 What is the most likely cause of the problem?
-Incorrect default gateway
You manage a network that has multiple internal subnets. You connect a workstation to the 192.168.1.0/24 subnet. This workstation can communicate with some hosts on the private network, but not with other hosts. You run ipconfig /all and see the following: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix: mydomain.local Description: Broadcom network adapter Physical Address: 00-AA-BB-CC-74-EF DHCP Enabled :No Autoconfigration Enabled: Yes IPv4 Address: 192.168.1.102 (preferred) Subnet Mask: 255.255.0.0 Default Gateway: 192.168.1.1 DNS servers: 192.168.1.20 192.168.1.27 What is most likely cause of the problem?
-Incorrect subnet mask
Which of the following strategies are used to prevent duplicate IP addresses from being used on a network? (2)
-Install a DHCP server on the network -Use Automatic Private IP Addressing
You are a network technician for a small corporate network. The Support Manager recently decided to add a new workstation to the network to handle an upcoming project in her department. To accommodate specific network communication needs for this project, you need to upgrade the network connection speed for the workstation in the Support Office.
-Install the 1000BaseTX network adapter in the Support workstation -Connect the Support workstation to the network using a Cat5e cable -Verify that the Support workstation can communicate with the Internet Explanation Select the 1000BaseTX network adapter and reconnect the Cat5e cable. The 1000BaseTX network adapter supports Gigabit Ethernet. Complete the following steps: 1. In the Support Office, switch to the motherboard view of the computer (turning off the workstation as necessary). 2. On the Shelf, expand the Network Adapters category. 3. Identify the network adapter that supports Fast Ethernet 1000BaseTX. Drag the network adapter from the Shelf to a free PCI-E slot on the computer. 4. To connect the computer to the network, switch to the back view of the computer. 5. Drag the Cat5 cable connector from the motherboard's NIC to the port of the 1000BaseTX network adapter. 6. To verify the connection to the local network and the Internet, switch to the front view of the computer. 7. Click the power button on the computer case. 8. After the workstation's operating system is loaded, click the networking icon in the Task Bar and click Open Network and Sharing Center. The diagram should indicate an active connection to the network and the Internet. You can also confirm the speed of the connection by clicking Local Area Connection 2 in the Network and Sharing Center.
In the OSI Model, which of the following functions are performed at the Application Layer?
-Integration of network functionality into the host operating system -Enabling communication between network clients and services
Which two of the following statements about the Dynamic Host Configuration Protocol (DHCP) are true
-It can deliver other configuration information in addition to IP addresses -A DHCP server assigns addresses to requesting hosts
Which of the following are characteristics of coaxial network cable? (Choose three)
-It uses two concentric metallic conductors. -The ends of the cable must be terminated. -It has a conductor made from copper in the center of the cable.
Which of the following connectors are used with fiber optic cables and include both cables in a single connector? (*Select two.)
-LC -MT-RJ
The Data Link Later of the OSI Model is comprised of two sublayers. What are they?
-LLC -MAC
You have a server at work with a custom application installed. Connections to the server that use the custom application must use IPv6. The server is currently running IPv4. You are the only person who connects the server, and you always use your Linux laptop for the connection. Your laptop supports both IPv4 and IPv6. The rest of your company network runs only IPv4. You need a cost-effective solution to allow your laptop to connect to the server. Your solution must also support communication through NAT servers. Which client software should you use to connect to the server?
-Miredo
A video conference call consisting of multiple participants uses ____________ network transmissions?
-Multicast
Which of the following address types is shared by multiple hosts, and is used to form groups of computers that should receive the same data stream?
-Multicast
Which type of address is the IP address 232.111.255.250?
-Multicast
You are working on a small office/home office (SOHO) network. The owner of the SOHO has decied to change his Internet Service Provider (ISP) to EtherSpeed. The ISP has installed a connection to both RJ45 jacks on the wall plate. You are responsible for selecting the correct router to connect the SOHO network to the Internet. You want to use the fasted connection speed available while providing for security for both computers (named Home-PC and Home-PC2)
-Place the Ethernet router with firewall on the Bench -Connect the computers to the Ethernet router with Cat5e cables -Connect the Ethernet router to the RJ45 jack on the wall plate using a Cat5e cable -Plug in the Ethernet router -Confirm that the computers are properly connected to the Internet Explanation To complete this lab, you need to make the following choices: Select the Ethernet router with Firewall capabilities. Your ISP provides a connection to the Internet up to the wall plate. You can protect a home computer by using a router with the firewall built in. Connect the Ethernet router to the Internet with a Cat5e Ethernet cable. To connect the computers to the router's integrated Ethernet LAN ports, use the existing Cat5e Ethernet cables. Cat3 cable is not designed to support 100 Mbps Ethernet. To complete this lab, follow these steps: 1. On the Shelf, expand the Networking Devices category. 2. Read the description for each device. Drag the Ethernet router with firewall to the Workspace. 3. Switch to the back view of the switch, the router, and the cable modem. 4. To connect the Home-PC to the router, select the Ethernet cable on the switch port 3 (i.e., the third Ethernet port from the left), and drag it to an open Ethernet LAN port on the router. (LAN ports are the first four ports on the left of the router.) 5. To connect the Home-PC2 to the router, repeat step 4 for the Ethernet cable connected to switch port 4. 6. To connect the router to the Internet connection, select the remaining Ethernet cable on the switch (i.e., port 1), and drag it to the open Ethernet WAN port on the router. (The WAN port is the last port on the right of the router.) 7. Select the Ethernet cable on the cable modem and drag it to one of the RJ45 ports on the wall plate. 8. To plug in the router, select the DC power connector on the switch and drag it to the power port on the router. 9. To confirm that Home-PC is properly connected to the SOHO network and Internet, click the Windows icon on the monitor on the left. 10. In the notification area, click the networking icon and click Open Network and Sharing Center. The diagramshould indicate an active connection to the home network and the Internet. 11. Repeat steps 9 and 10 to confirm the connection for Home-PC2.
You are working on a small office/home office (SOHO) network. Recently, you added a cabel modem to the network so Home-PC could connect to the internet. Currently, this networking configuration only allows Home-PC (the computer on the left) to connect to the internet, but now you also have Home-PC2 (the computer on the right). You need to add a hub to the network so that both computers can communicate with each other, as well as have a successful connection to the Internet. The computers do not need guaranteed bandwidth for their network connections.
-Place the hub on the Bench -Connect the cable modem to the hub -Use Cat5e cable to connect both computers to the hub Show Details -Provide power to the hub -Confirm that the two computers are properly connected to the Internet Show Details Explanation Complete the following steps: 1. On the Shelf, expand the Networking Device category. 2. Drag the 1000BaseTX Ethernet hub to the Workspace. 3. Switch to the back view of the hub. 4. On the Shelf, expand the Cables category. 5. To plug in the hub, select the power adapter on the Shelf. 6. In the Selected Component window, drag the DC power connector to the port on the hub. 7. In the Selected Component window, drag the AC power adapter end to an empty outlet on the wall or surge protector. 8. To connect the cable modem to the hub, switch to the back view of the Home-PC (the computer on the left). 9. Select the Cat5e cable connected to the motherboard's NIC, and drag the connector to an Ethernet port on the hub. 10. To connect the Home-PC to the hub, expand the Cables category on the Shelf. 11. Select the Cat5e cable with RJ-45 connectors. 12. In the Selected Component window, drag a connector to the Ethernet port on the back of Home-PC. 13. In the Selected Component window, drag a connector to an Ethernet port on the hub. 14. To confirm that Home-PC is properly connected to the network and Internet, click the Windows icon on the monitor on the left. 15. In the notification area, click the networking icon and click Open Network and Sharing Center. The diagram should indicate an active connection to the home network and the Internet. 16. To connect Home-PC2 (the computer on the right) to the hub, switch to the Workspace. 17. Repeat steps 11 through 13 to make the connection, and then repeat steps 14 and 15 to confirm the connection.
You are working on a small office/home office (SOHO) network. After adding a hub to the network so Home-PC and Home-PC2 could communicate and have successful connection to the Internet, the customer has noticed a connection delay whenever the computers use the network at the same time. You believe the delay might be related to the shared bandwidth on the network.
-Place the managed switch on the Bench -Connect the cable modem to the managed switch -Use Cat5e cables to connect both computers to the managed switch -Provide power to the managed switch -Confirm that the two computers are properly connected to the local network and the Internet Explanation To meet the requirements, you will need to select a managed switch. The following are the essential differences between the networking devices offered in this scenario: A switch creates a connection for computers in a local area network, and offers guaranteed bandwidth between the devices. Types of switches include: Managed switches allow administrators to change the port configurations, including the following: Port speed Filters based on network adapter MAC addresses Unmanaged switches are autonomous in their function, requiring no port management or configuration. A router connects devices on two different networks, but many routers (such as the ones shown here) also include integrated Ethernet ports for the LAN. Selecting a router with an integrated hub or switch is not necessary for this scenario. Complete the following steps: 1. On the Shelf, expand the Networking Devices category. 2. Read the device descriptions to identify the switch. Drag the Managed Switch to the Workspace (preferably next to the existing hub). 3. Switch to the back view of the managed switch and the hub. 4. To plug in the switch, select the DC power connector on the hub and drag it to the power port on the switch. 5. To connect the Home-PC, Home-PC2, and the cable modem to the switch, select an Ethernet cable on the hub, and drag it to an open Ethernet port on the switch. Repeat for each Ethernet connection on the hub. 6. To confirm that Home-PC is properly connected to the network and Internet, click the Windows icon on the monitor on the left. 7. In the notification area, click the networking icon and click Open Network and Sharing Center. The diagram should indicate an active connection to the home network and the Internet. 8. To confirm the connection for Home-PC2, switch back to the bench and click the Windows icon on the monitor on the right. 9. Repeat step 7.
CorpServ is a small company with 14 client systems and a network printer. Because there are only a limited number of networked systems, you decide to use APIPA addressing for the network. With APIPA configured, all systems are able to communicate with each other but you are having trouble configuring Internet access. What is the likely cause of the problem?
-Private addresses cannot directly communicate to hosts outside the local subnet.
F-Type connectors are typically used with cables using which of the following standards? (Select two)
-RG-6 -RG-59
Which of the following cable classifications are typically used for cable and satellite networking with coaxial cables?
-RG-6 -RG-59
Which of the following connector types are used with UTP cables? (Select two.)
-RJ11 -RJ45
You have a Windows Server 2012 system that you want to use as a DHCP Relay Agent. Which Windows Server 2012 service would you use to do this>
-Routing and Remote Access
In the OSI Model, which of the following functions are performed at the Presentation Layer?
-Specify data format -Encrypt and compress data
You are configuring the DHCP Relay Agent role service on a Windows server. Which of the following is required step for the configuration?
-Specify which server network interface the agent listens on for DHCP messages
You manage a network that uses IPv6 addressing. When clients connect devices to the network, they generate an interface ID and use NDP to learn the subnet prefix and default gateway. Which IPv6 address assignment method is being used?
-Stateless autoconfiguration
Which of the following best describes the purpose of using subnets?
-Subnets divide an IP network address into multiple network addresses.
You manage a subnet that uses the following subnet address: 198.162.1.0/23. Which of the following best describes how addressing is configured for the subnet?
-Supernetting
You have a small network connected to the Internet as shown is the Exhibit. You need to configure the default gateway address on Wrk1 so that it can communicate with hosts on the Internet. Which address would you use for the default gateway address?
-The IP address assigned to Fa0/0 on Router 1
You've connected a cable certifier to an RJ45 wall jack, and the output shown below is displayed on the device. What does this output indicate? (Select two.)
-The cable is functioning correctly -This is a crossover cable
After installing a new DHCP server on the network, you need to verify that network devices are receiving IP addressing via DHCP. You reboot a Windows XP client system using the ipconfig command, receive the following information: Ethernet adapter Local Area Connection 1: Description .. : CardBus-II 10/100 PC Card Physical Address.. : 02-00-4C-4F-3F-50 DHCP Enable.. : Yes Auto-configuration Enabled.. :/yes Auto-configuration IP Address.. : 169.254.25.129 Subnet Mask: 255.255.0.0 Which of the following statements are true?
-The client system is configured to use DHCP -The client system is unable to reach the DHCP server
Due to widespread network expansion, you have decided to upgrade the network by configuring a DHCP server for the network. THe network uses Linux, Windows, and MAC OS X client systems. You configure the server to distribute IP addresses from 192.168.2.1 to address 192.168.2.100. You use the subnet mask of 255.255.255.0. After making all setting changes on the DHCP server, you reboot each client system but they are not able to obtain an IP address from the DHCP server. Which of the following would explain the failure?
-The clients must be configured to obtain IP addressing from a DHCP server
If dynamic DNS is being used, which of the following events will cause dynamic update of the host records? (2)
-The ipconfig /release command is entered on a workstation -The DHCP server renews an address lease
Which of the following are characteristics of an LC fiber optic connector? (Choose two.)
-They are half the size of standard connectors. -They use a housing and latch system similar to an RJ-45 UTP connector
Which of the following are characteristics of an MT-RJ fiber optic connector? (Select two)
-They can be used with multimode fiber optic cables. -They use metal guide pins to ensure accurate alignment.
You administer a network with Windows 2000 and UNIX servers, and Windows 2000 Professional, Windows 98, and Macintosh clients. A user of a Windows 98 computer calls you one day and says he is unable to access resources on the network. You type ipconfig on the user's computer and receive the following output: 0 Ethernet adapter: IP address: 169.254.1.17 Subnet Mask: 255.255.0.0 Default Gateway :... You also check your NIC and see the link light on. What might the problem be?
-Unavailable DHCP server
Which type of address is the IP address 198.162.12.254/24?
-Unicast
Which type of address is used in a packet to address the packet to a single host?
-Unicast
You have configured your organization's DHCP to dynamically assign IP addresses to DHCP clients using a lease duration of four days. A user's workstation is powered on and receives addressing information from this DHCP server Monday morning at 8AM. When will the client contact the DHCP server to renew the lease (by default)?
-Wednesday morning
Which of the following are characteristics of Teredo tunneling? (3)
-Works through NAT -Dual stack hosts -Tunnel endpoints configured on hosts
You are implementing a DHCP server for your segment. Your segment's IP address is 192.168.1.0. Your default gateway address is 192.168.1.254. Your DNS server address is 192.168.1.1. Your default gateway is configured as a NAT router to translate addresses between network segments. You configured the 03 Router option on your DHCP server so it can deliver the IP address of the default gateway to workstations. After configuring your workstations to get their IP addressing information dynamically, your users complain that they are unable to access websites on the Internet. How can you resolve this problem?
-You must configure your DHCP server with an option that delivers the IP address of the DNS server (Option 06)
Which TCP/IP utility gives you the following output? Interface: 192.168.4.101 on Interface 0x3 Internet Address Physical Address Type 192.168.1.23 00-d1-b6-b7-c2-af dynamic
-arp
Which of the following tools would you use to view the MAC addresses associated with the IP addresses that the local workstation has contacted recently?
-arp
Which TCP/IP utility gives you the following output? (shows current entries in the computer's ARP cache)
-arp -a
Which of the following utilities produced this output? (very detailed)
-dig
You need to perform a reverse lookup of the 10.0.0.3 IP address. Which command can you use to accomplish this? (2)
-dig -x 10.0.0.3 -nslookup 10.0.0.3
You want to be able to view the DNS server address that a computer is using. Which of the following utilities would you use? (2)
-ifconfig -ipconfig
You need to configure a Cisco RFC 1542 compliant router to forward any received DHCP frames to the appropriate subnet. The address of the remote DHCP server is 172.16.30.1. Which of the following commands would be used to configure the router?
-ip helper-address 172.16.30.1
You have been called in to troubleshoot a connectivity problem on a newly installed Windows Server 2003 system. The system is operating satisfactorily and is able to communicate with other systems on the local network. However it is unable to access any systems on other segments of the corporate network. You suspect that the default gateway parameter for the system has not been configured, or may be configured incorrectly. Which of the following utilities are you most likely to use to view the default gateway information for the system?
-ipconfig
You administer a NetBIOS-based network that uses the TPC/IP protocol. You are trying to troubleshoot a computer that is unable to conact a server by its NetBIOS name. Which command can you use to check the connection?
-nbtstat
Which TCP/IP utility gives you the following output? (shows resolved NETBIOS name cache for a computer) Local Area Connection: Node IpAddress: 192.168.1.111 Scope ID [] NetBIOS Remote Cache Name Table Name Type Host Address Life(sec) NTINE.ES 54 Un 192.168.1.23 395 NTINE 20 Un 192.168.1.23 45 AUDIO 00 Un 192.168.1.168 585
-nbtstat -c
Examine the following output: Active Connections Proto Local Address Foreign Address State TCP SERVER1:1036localhost:4832TIME_WAIT TCP SERVER1:4798 localhost:1032TIME_WAIT TCP SERVER1: 1258 pool-141-150-16-231.mad.east.ttr:24076 CLOSE_WAIT TCP SERVER1:2150 cpe-66-67-225-188.roc.res.rr.com:14100 ESTABLISHED TCP SERVER1:268 C872c-032.cpe.net.cale.rers.com:46360 ESTABLISHED TCP SERVER1:2995 ip68-97-96-186.ok.ok.cox.net:23135 ESTABLISHED Which of the following utilities produced this output?
-netstat
Your computer is sharing information with a remote computer using the TCP/IP protocol. Suddenly, the connection stops working and appears to hang. Which command can you use to check the connection?
-netstat
Which TCP/IP utility gives you the following output? (shows status of all connections and listening ports)
-netstat -a
Which TCP/IP utility gives the you the following output? (showing the computer's route table)
-netstat -r
Which command displays network activity statistics for TCP, UDP, and IP?
-netstat -s
Examine the following output: Server: helicuplar.xct.takro.net Address: 209.53.4.130 Name: westsim.com Address: 64.78.193.84 Which of the following utilities produced this output?
-nslookup
Mary calls to tell you that she can't connect to an intranet server called WebSrv1. From her computer, you ping the server's IP address. The ping test test is successful. Which tool would you use on her workstation next to troubleshoot the problem?
-nslookup
You are troubleshooting a network connectivity issue on a Unix system. You are able to connect to remote systems by using their IP address, but unable to connect using the hostname. You check the TCP/IP configuration, and note that DNS server IP address is configured. You decide to run some manual resolution queries to ensure that the communication between the Unix system and the DNS server are working correctly. Which utilities can you use to do this?
-nslookup -dig
Which TCP/IP utility gives you the following output? (shows Packets sent, received, and lost)
-ping
You work in an office that uses NetWare servers and Windows NT 4.0 servers. The network uses both the TCP/IP and IPX/SPX protocols. You are sitting at a workstation that uses Windows 95 OSR2. An application you are using is unable to contact a Windows NT server named FileSrv2. Which command can you use to determine whether your computer can still contact the server?
-ping
While working on a Linux server, you are unable to connect to Windows Server 2003 system across the Internet. You are able to ping the default gateway on your own network, so you suspect that the problem lies outside of the local network. Which utility would you use to track the route a packet takes as it crosses the network?
-traceroute NOT ---> tracert <--- NOT
You have a computer that is connected to the Internet through a NAT router. You want to use a private addressing scheme for your computer. Which of the following IP addresses could you assign to the computer?
10.0.12.15 172.18.188.67 192.168.12.253
With an Ethernet 10BaseT network, the maximum cable length between a computer and the hub is:
100 meters
Your network follows the 100BaseTx specifications for Fast Ethernet. What is the maximum cable segment length allowed?
100 meters
What is the binary format for the following decimal IP address? 131.9.202.111
100000011.00001001.1001010.01101111
You have been tasked with designing a high-speed Ethernet network. Your client's building already has 150 ohm shielded twisted pair wiring installed. Due to budget constraints, they have asked you to reuse the existing wiring instead of installing new fiber optic cabling. Which Ethernet standard could you implement in this situation?
1000BaseCX
Which Gigabit Ethernet standard uses multimode fiber-optic cabling and supports network segments up to a maximum of 550 m long?
1000BaseSX
Which of the following Ethernet standards uses fiber optic cabling?(2 answers)
100BaseFX 1000BaseLX
Which of the following use the CSMA/CD access method?(2 answers)
10BaseT 1000BaseT
You would like to implement 10 Gbps Ethernet over a distance of 1 km or greater. Which of the following would be the minimum requirement for the implementation?(2 answers)
10GBaseLR standards Single mode fiber
Which of the following standards is used by SONET?
10GBaseLW
You have been tasked with designing an Ethernet network. Your client needs to implement a very high-speed network backbone between campus buildings; some of which are around 300 m apart. Fiber-optic cabling has already been installed between buildings. Your client has asked that you use the existing cabling that operates at full-duplex. Which Ethernet standard meets these guidelines?(2 answers)
10GBaseSR 1000BaseSX
Which of the following IP addresses is a valid IP address for a host on a public network?
142.15.6.1
Which port number is used by SNMP?
161
Which of the following is the last IP address that can be assigned to hosts on the 166.70.0.0 network using the default subnet mask?
166.70.255.25
Which of the following is not one of the ranges of IP addresses defined in RFC 1918 that are commonly used behind a NAT server?
169.254.0.1 - 169.254.255.254
Which of the following is not one of the ranges of IP addresses defined in the RFC 1918 that are commonly used behind a NAT server?
169.254.0.1 - 169.254.255.254
you have two switches connected together as shown in the following diagram. How many broadcast domains are there in the network?
2
You are planning a network for an educational campus. Due to the size of the buildings and the distance between them, you have elected to use 10BaseFL hubs, cabling, and network interface cards. What is the maximum length for the network cable between a workstation and a hub?
2000 meters
What is the IP address of the DNS server that performed this name resolution?
202.64.49.150
What is the decimal format for the following binary IP address? 11001110.00111010.10101010.01000011
206.58.170.67
To increase security on your company's internal network
443
To increase security on your company's internal network, the administrator has disabled as many ports as possible. Now, however, though you can browse the Internet, you are unable to perform secure credit card transactions. Which port needs to be enabled to allow secure transactions?
443
You are configuring PuTTY to be used to access the CLi of a Cisco switch Which of the following configuration values would prevent PuTTY from connecting? (Select two)
4600 baud Flow control = RTS/CTS
You want to maintain security on your internal network
53
You manage a network with two locations: Portland and Seattle. Both locations are connected to the Internet. All computers in both locations are configured to use IPv6. You would like to implement an IPv6 solution to meet the following requirements: -Hosts in each location should be able to use IPv6 to communicate hosts in the other location through the IPv4 Internet. -You want to use a site-to-site tunneling method instead of a host-to-host tunneling method. Which IPv6 solution should you use?
6-to-4
select the statement that best describes a broadcast storm.
A Broadcast storm occurs when there are so many broadcast messages on the network that they approach or exceed the network bandwidth..
While viewing the status of the interfaces on a Cisco switch, you see an abnormally large number of CRC errors on one interface. This interface is connected to a user's workstation located in a cubicle on the 2nd floor. What could be causing this to happen?
A strong emitter near the cable run connected to that interface
Using the exhibit to match the connector type on the left with the corresponding letter on the right.
A- DB-25 B- DB-9 C- RJ45 D- RJ11 E- LC F- BNC G- F-Type
Which of the following is a valid MAC address? 95ABC2F4.ABC5.569D.43BF FABC.875E.9BG6 AB.07.CF.62.16.BD 145.65.254.10
AB.07.CF.62.16.BD
Which of the following does a router acting as a firewall use to control packets
ACL
A host wants to send a message to another host with the IP address 115.99.80.157. IP does not know the hardware address of the destination device. Which protocol can be used to discover the MAC address? BOOTP ARP DNS DHCP IGMP ICMP
ARP
A router is configured with the login, no password condition for console access. Which of the following statements is true about access via a Telnet or SSH session?
Access is denied.
Your Cisco router has three
Add a permit
You are implementing a SOHO network for a local business. The ISP has already installed and connected a cable modem in the business. The business has four computers that need to communicate with each other and the internet. You examine each computer and notice only one of the four has a wireless NIC; they all have ethernet NICs. What should you purchase.
An unmanaged switch and Cat5e cabling
You need to replace a fiber optic cable that is connecting two switches together. You instpect the existing fiber cable and determine that it uses LC connectors. You also notice the cable's ferrule has a slight slant to it. Which polish grade should you use to replace the existing cable?
Angled Physical Contact polish
Match the network function or device on the left with the OSI model layer it is associated with on the right.
Application-HTTP Presentation-ASCII Session-Session ID Number Transport-Port Numbers Network-Router Data Link-Switch Physical-Wireless Access Point
You provide Internet access for a local school. You want to control Internet access based on user, and prevent access to specific URLs. Which type of firewall should you install?
Application-level
You are creating an Ethernet network for your company. The shipping department is located in a different building that is located 150 meters from the main wiring closet. You connect a single Cat6e cable to connect the wiring closet to the shipping building. Which of the following are you most likely to experience?
Attenuation.
You have just connected four switches as shown in the Exhibit. Assuming the default switch configuration, which switch will become the root bridge?
B
Which of the following routing protocols uses paths, rules, and policies instead of a metric for making routing decisions?
BGP
Which of the following features are common functions
Bandwith shaping Spam Filtering
A switch running STP is a backup bridge. What state is it in?
Blocking
Which of the following topologies connects all devices to a trunk cable?
Bus
You are making Ethernet drop cables using Cat5e cable and RJ45 connectors. You need to remove the plastic coating over the cable to expose the individual wires. Which tool should you use?
Cable Stripper
You recently installed a new all-in-one security appliance in a remote office
Change the default Configure the device's authentication
Match each type of switch on the left with its corresponding characteristics on the right. Each switch may be used once, more than once, or not at all.
Commonly sold at retail stores Unmanaged switch Provide port security features Managed switch Support VLANs Managed switch Provide very few configuration options Unmanaged switch Can be configured over a network connection Managed switch Can be configured over a dedicated communication channel Managed switch
Match each switch management method on the left with its corresponding characteristics on the right. Each method may be used once, more than once, or not at all.
Competes with normal network traffic for bandwidth In-band management Uses a dedicated communication channel Out-of-band management Must be encrypted to protect communications from sniffing In-band management Does not compete with normal network traffic for bandwith Out-of-band management Affected by network outages In-band management
Computers A and B are on the same VLAN and are separated by two switches, as shown in the exhibit. Computer A sends a Fram to Computer B. Which of the following best describes the composition of the frame as it travels from A to B?
Computer A sends a normal frame. The first switch appends a VLAN ID to the frame. The second switch removes the VLAN ID before forwarding it to Computer B.
Your company has decided to temporarily partner with a third-party organization for an upcoming project. This requires your company's network and the third-party's network to be connected via a dedicated WAN connection. what should you do to allow routing information to the exchange?
Configure a border router to use route redistribution.
You want to create a rollover cable that has an RJ-45 connector on both ends. How should you connect the wires within the connectors?
Connect pin 1 to pin 8, pin 2 to pin 7, pin 3 to pin 6, and pin 4 to pin 5
Match the Cisco device password type on the left with its function on the right.
Controls the ability to log on through a LAN or WAN interface configured on the device. VTY Controls the ability to switch configuration modes EXEC Controls the ability to connect to the device using a direct connection Console
you have a network configured to use the OSPF routing protocol. Which of the following describes the state when all OSPF routers have learned about all other routes in the network.
Convergence
You have two switches that you need to connect using their uplink ports. The switches do not support auto-MDI. Which type of cable should you use?
Crossover
You need to transfer data from one laptop to another and would like to use an Ethernet cable. You do not have a hub or a switch. Which type of cable should you use?
Crossover
You want to connect the LAN port on a router to the uplink port on a switch. The switch does not support auto-MDI. Which type of cable should you use?
Crossover
You have decided to implement Gigabit Ethernet on your network. Each switch port is connected to a single device. Following the installation, you find one device connected to a switch that is only running at 100 Mbps. Which of the following are likely causes?
Crosstalk.
Which firewall implementation creates a buffer
DMZ
You have just connected a new computer to your network. The network user static IP addressing. You find that the computer can communicate with hosts on the same subnet, but not with hosts on a different subnet. No other computers are having a problem Which of the configuration values would you most likely need to change?
Default gateway.
You have a network that occupies the top floor of a three story building. The WAN service provider has installed the line for the WAN service into the building in a wiring closet on the main floor. What would you use to relocate the WAN line into a wiring closet on your floor?
Demarc Extension
Match the Etherchannel protocol on the left with its characteristics on the right.
Desirable mode places the port in a negotiating state. Port Aggregation Protocol (PAgP) Based on the 802.3ad standard link Aggregation control protocol(LACP) Passive mode places the port into a passive negotiation state. link aggregation control protocol (LACP) Auto mode places the port into a passive negotiating state. Port Aggregation Protocol (PAgP) Active more places the port in a negotiating state. link Aggregation control protocol(LACP)
You have just installed a packet-filtering firewall on your network
Destination address Port number Source address
Which of the following statements describe how VLANs effect broadcast traffic within an internetwork?
Devices on the same VLAN have the same subnet address Broadcast traffic is transmitted only within a VLAN
Which of the following best describes the concept of VLAN?
Devices on the same network logically grouped as if they were on separate networks
Which of the following are true for the IS-IS routing protocol? select two
Divides large networks into areas Supports IPv6 routing
You manage the two-location network shown in the exhibit. Workstations and servers at each location connect to a patch panel using behind-the-wall wiring. The patch panel.... Drag the cable type on the left to the most appropriate network location on the right.
Drop Cables Cat6 straight-through UTP Patch Cables Cat6 straight-through UTP Uplink Cables Cat6 crossover UTP WAN Cable Single-mode fiber optic
A router is connected to a network 192.168.1.0/24 and network 192.168.2.0/24. The router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24. There is no default route on router. The router receives a packet addressed to network 10.1.0.0/16. What will the router do with the packet?
Drop the packet.
A user reports that network access from her workstation is very slow. The problem does not seem to be affecting any other users. Which of the following conditions is the most likely cause?
Duplex mismatch
You want to connect your small company network to the Internet. Your ISP provides you with a single IP address that is to be shared between all hosts on your private network. You do not want external hosts to be able to initiate connection to internal hosts. What type of NAT should you implement?
Dynamic
You are troubleshooting a client connectivity problem on an Ethernet network. The client system has intermittent connectivity to the network. You discover that the UTP patch cable is run 75 feet from the wall outlet, passes through the ceiling and over several florescent light fixtures before reaching the client system. Which of the following may be a cause of the connectivity problem?
EMI interfaace.
You have configured a remote access server to accept dial-up connections for remote access clients. Remote clients are able to connect successfully and access resources on the remote access server. However, the remote clients are not able to connect to other devices located on the same subnet where the remote access server is located. Which action would likely correct the problem?
Enable proxy arp on the LAN connection for the remote access server.
You need to disable the FastEthernet 0/0 interface on a switch Drag the command on the left to the approbate configuration step on the right to accomplish this. Not all of the commands may be required
Enter global configuration mode conf t Enter interface configuration mode int fa0/0 Disable the interface shutdown Verify the interface is disabled show ip interface brief
The FastEthernet 0/0 interface on a s witch is currently disable. You need to enable it so a workstation can be connected to it. Drag the command on the left to the approbate configuration step on the right to accomplish this. Not all of the commands may be required
Enter global configuration mode conf t Enter interface configuration mode int fa0/0 Enable the interface no shut Verify the interface is disabled show interface status
You need to configure the FastEthernet 0/1 interface on a switch to automatically detect the appropriate link speed and duplex setting by negotiating with the device connected to the other end of the link. Drag the command on the left to the approbate configuration step on the right to accomplish this. Not all of the commands may be required
Enter global configuration mode conf t Enter interface configuration mode int fa0/1 Set speed of the interface speed auto Set the duplex setting for the interface duplex auto
You have just signed up for a broadband home Internet service that uses coaxial cable. Which connector type will you most likely use?
F-type
You want to allow your users to download files from a server running the TCP
FTP
You are moving a client to a new location within an Ethernet network. Previous to the move, the client system did not have any difficulty accessing the network. During the relocation, you attach a patch cable from the client system to the wall jack and from the patch panel to the switch. Once connected you do not get a link light on the network card or the switch. You swap out the cable running between the patch panel and the switch with a known working one but you can still not connect. Which of the following might you suspect as the problem?
Failed patch cable between the client system and the wall jack.
Ethernet 100BaseFX networks use what type of cabling?
Fiber-optic
Which of the following is the best device to deploy to protect your private network from a public untrusted network? Gateway Hub Firewall Router
Firewall
You are the administrator of your company's network. You want to prevent unauthorized access to your intranet from the Internet. Which of the following should you implement? Firewall ICS Packet Internet Groper Proxy server
Firewall
A router is connected to a network 192.169.1.0/24 and network 192.168.2.0/24. The router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24. The router is also configured with a static route of 0.0.0.0 with a mask of 0.0.0.0. The router receives a packet addressed to the network 10.1.0.0/16. What will the router do with the packet.
Forward the packet to the next hop router specified by the route network 0.0.0.0
Which of the following protocols provide gateway redundancy? select all that apply
HSRP GLBP VRRP
You have been given a laptop to use for work
Host-based
You have been given a laptop to use for work. You connect the laptop to your company network, use it from home, and use it while traveling. You want to protect the laptop from Internet-based attacks. What solution should you use?
Host-based firewall
Which of the following devices does not segment the network?
Hub
Which of the following protocols allows hosts to exchange messages to indicate problems with packet delivery
ICMP
Match the default administrative distance with the route type.
IGRP/100 RIP/120 Static Route/1 EIGRP internal route/90 OSPF/110 EIGRP Summary Route/5 Connected Interface/0 EIGRP external Route/170
You are asked to recommend an email retrieval protocol for a company's sales team. The sales team needs to access email from various locations and possible different computers. The sales team does not want to worry about transferring email messages or files back and forth between these computers. Which email protocol was designed for this purpose?
IMAP4
You have a private network connected to the internet. Your routers will not share routing information about your private network with internet routers. Which of the following best describes the type of routing protocol you would use?
IPG
Which of the following are reasons to configure VLAN's on a switch as opposed to using switches without VLANs?
Increased Security Increased Number of broadcast domains
Which of the following is true about the MAC address? (Select two) It is typically represented by octets of decimal numbers between 0-255 It is typically represented by hexadecimal numbers. It is a 64-bit address It is a 48-bit address It is a 32-bit address
It is typically represented by hexadecimal numbers. It is a 48-bit address
Which of the following statements accurately describes how a modem works? (Select two)
It modulates digital data from the PC into analog data and transmits it on a telephone network. It demodulates analog data from a telephone network into digital PC data.
A switch running STP is in a learning state. A message destined for a different network segment arrives at the switch. Which of the following best describes what the switch will do?
It uses the source MAC address and network segment information to build its bridge database, but does not forward the message
At which OSI model layer does a media converter operate?
Layer 1
Match the firewall type
Layer 2- V Layer 3- R Counts-R Does-V Different-R Same-V
You have a router configured to share routing information using RIP. In addition, you have a single static route that identifies a default route for all other networks. The next hop router for the default has changed. You need to make the change with the least amount of effort possible. What should you do?
Manually reconfigure the default route to point to the new next hop router.
Which of the following tests can be performed by a TDR?
Measure the length of a cable. Identify the location of a fault on a cable.
You have a server that has a 100BaseFX network interface card that you need to connect to a switch. The switch only has 100BaseTX switch ports. Which device should you use? Repeater Hub Bridge Media converter Gateway
Media converter
You have been asked to implement a network infrastructure that will accommodate failed connections. Which of the following network topologies provides redundancy for a failed link?
Mesh
You have a network that uses a logical bus topology. How do messages travel through the network?
Messages are broadcast to all devices connected to the network.
You have a network that uses a logical ring topology. How do messages travel through the network?
Messages travel from one device to the next until they reached the destination device.
When multiple routes to a destination exist, what is used to select the best possible route?
Metric
Which of the following geographic network types are typically managed by a city as a public utility?
Metropolitan Area Network (MAN)
You manage a network with multiple subnets connected to the Internet. A user reports that she can't access the new server used in the accounting department. You check the problem and find out that her computer cannot access any server on the subnet, however the computer does access other computers on other subnets as well as the Internet. Which of the following is most likely the cause of the problem?
Missing route on the default gateway router.
Which of the following functions are performed at the Physical Layer of the OSI Model?
Movement of data across network cables
You have a large TCP/IP network and want to keep hosts' real time clock synchronized. What protocol should you use?
NTP
At what OSI layer does a router operate to forward network messages?
Network
Which network component connects a device with the transmission media and allows it to send and receive messages? Client Network interface card Peripheral Protocol Server
Network interface card
You have a network connected using a physical bus topology. One of the cables connecting a workstation to the bus breaks. Which of the following best describes what happens to network communications?
No device is able to communicate.
You are installing network wiring for a new Ethernet network at our company's main office building. The project specs call for Category 5 UTP network cabling and RJ-45 wall jacks. near the end of the project, you run out of wire before the last few runs are complete. You have a spool of Category 3 network cable in storage. Upon investigation, it appears very similar to Category 5 wiring. Should you substitute Category 3 cabling for Category 5 cabling to finish the project?
No, Category 5 cabling has more twists per inch that Category 3 cabling to reduce cross-talk and support higher data rates.
You are configuring a switch so that you can manage it via PuTTY from the same network segment as the switch. On the switch, you enter the following commands: switch#config terminal switch(config)#interface vlan 1 switch(config-if)#ip address 192.168.1.10 255.255.255.0 Will this configuration work?
No, the no shutdown command needs to be entered.
You are building a new network for a small startup financial services company. Security is paramount, so each organization within the company will have its own network segment separated by a router. However, funds are limited, and you have been asked to keep costs to a minimum. You have acquired a used fiber optic switch and want to use it to create a fiber optic backbone that interconnects all of the routers. You purchased several used multimode GBIC modules on ebay that you will install in each router to allow them to connect to the switch. Both the switch and the GBIC modules use MT-RJ connectors. You purchased several used cables from Amazon. However, when they arrived, you noticed that they use LC connectors. Fortunately, with some force, you found that you are able to get the LC connectors on the cables to lock into the MJ-RJ connectors on the GBIC modules and on the switch. Will this implementation work?
No, you should purchase path cables that use MT-RJ connectors
You are building a new network for a small startup financial services company. Security is paramount, so each organization within the company will have its own network segment separated by a router. However, funds are limited, and you have been asked to keep costs to a minimum. You have acquired a used fiber optic switch and want to use it to create a fiber optic backbone that interconnects all of the routers. You purchased several used single mode GBIC modules on ebay that you will install in each router to allow them to connect to the switch. Both the switch and the GBIC modules use MT-RJ connectors. You connect each module to the switch with 1 meter multimode patch cables. Will this implementation work?
No, you shouldn't use multimode patch cables with single mode GBIC moduals
Based on the diagram, which network line code technique is being used?
Non-Return-to-Zero
Match the description on the left with the appropriate network signal line code on the right.
Non-Return-to-Zero Binary 1s are represented by positive voltage while 0s are represented by negative voltage. There is no zero voltage state between bits. Manchester The transition from one voltage level to another is used to represent binary data Return-to-Zero Inverted A 0 is represented by sending a light pulse. A 1 is represented by sending no light pulse. Return-to-Zero Binary 0s and 1s are transmitted by sending voltage pulses, with the voltage returning to zero between pulses.
Which of the following routing protocols divides the network into areas, with all networks required to have an area 0 (area 0 identifying the backbone area)?
OSPF
Which of the following routing protocols are classified as link state routing protocols? select two
OSPF IS-IS
You work for a large, multinational organization that has an extensive global network that is interconnected using WAN links and routers.
One of the intermediate routers is an MTU black hole.
After blocking a number of ports to secure your server
Open port 25 to allow SMTP service
Which of the following TCP/IP protocols do e-mail clients use to download messages from a remote mail server?
POP3
Match the firewall type on the right with the OSI layers at which it operates. Note: Each OSI Layer can be used once, more than once, or not at all.
Packet Filtering Firewall OSI Layer 3 Circuit-level Proxy OSI Layer 5 Application-level Gateway OSI Layer 7 Routed Firewall OSI Layer 3 Transparent Firewall OSI Layer 2
Match the firewall type on the right
Packet Filtering Firewall- 3 Circuit Level Proxy - 5 Application Level Gateway - 7 Routed Firewall - 3 Transparent Firewall - 2
Which of the following is used to terminate individual wires from a 25 pair or 100 pair cables using female RJ-45 ports?
Patch panel
You have implemented a network where each device provides shared files with all other devices on the network. What type of network do you have?
Peer-to-peer
At which layer of the OSI Model do hubs operate?
Physical
Network Signaling is a function of which later of the OSI Model?
Physical Layer
You need to terminate a Cat 6 UTP cable with and RJ045 connector. Your organization's IT policy states that all cable connectors must be wired according to TIA568A standards Drag the UTP wire on the left to the correct pin in the RJ45 connector on the right
Pin 1: White w/ green stripe Pin 2: Solid Green Pin 3: White with orange Stripe Pin 4: Solid blue Pin 5: white w/ blue stripe Pin 6: solid orange Pin 7: white w/ brown stripe Pin 8: Solid brown
1. Points a hostname to an IPv4 addresss 2. Provides alternate names to hosts that already have a host record 3. Points an IP address to a hostname 4. Points a hostname to an IPv6 address 5. Identifies servers that can be used to deliver mail
Points a hostname to an IPv4 address... A Provides alternate names to hosts that already have a host record... CNAME Points an IP adress to a hostname... PTR Points a hostname to an IPv6 address ... AAAA Identifies servers that an be used to deliver mail ... MX
Which of the following techniques allows incoming traffic addressed to a specific port to move through a NAT router and be forwarded to a specific host?
Port forwarding
Which statements accurately describes port states of both bridges and switches?
Ports in a blocked state still receive BPDUs In the learning state the MAC address table can be populated, but frames not forwarded.
Which of the following are advantages of using the Spanning Tree Protocol (STP) in network segmented bridges?
Prevents message loops from forming Identifies the optimal path between network devices. Lets you provide redundancy by using more then one connection between devices, making your network more reliable.
You have a small network at home that is connected to the Internet. On your home network you have a server with the IP address of 192.168.55.199/16. All computers on your home network can connect to the Internet. From your work office, you can try to access your home computer using its IP address, but are unable to communicate with the server. You are able to connect to other hosts on the Internet. Why can't you access the server?
Private addresses are not accessible through the Internet.
You manage a server that runs your company website
Proxy Server
You manage a server that runs your company Web site. The Web server has reached its capacity, and the number of client requests is greater than the server can handle. You would like to find a solution so that static Web content can be offloaded to a different server, while the Web server continues to process dynamic content. Which solution should you implement?
Proxy server
You computer has an IP address of 161.13.5.15. Your computer is on a:
Public network
Which of the following standards is typically used in a rollover cable?
RJ-232
Which of the following connectors is used with Ethernet 10BaseT networks?
RJ-45
Which of the following are requirements of the 1000BaseT Ethernet standards?(3 answers)
RJ-45 connectors The cable length must be less than or equal to 100m CAT 5e cabling
Which of the following connector types would you most likely use to connect a T1 WAN service?
RJ48c
You are creating an Ethernet network for your company. The shipping department is located in a different building that is located 150 meters from the main wiring closet. You connect a single Cat 6e cable to connect the wiring closet to the shipping building. Which of the following should you include in your plan?
Repeater
Based on the diagram, which type of proxy is handling the client's request
Reverse
Based on the diagram, which type of proxy server is handling the client's request?
Reverse Proxy Server
In which of the following topolgies does each device on the netowrk act as a repeater, sending the signal to the next device?
Ring
Which of the following topologies connects each device to a neighboring device?
Ring
Which of the following hardware devices links multiple networks and directs traffic between networks? Router Repeater Hub Bridge
Router
In the OSI Model, what is the primary function of the Network Layer?
Routes messages between networks
You manage a network with two switches. The switches are connected together through their Gigabit Ethernet uplink ports. You define VLAN 1 and VLAn 2 on each switch. A device on the first switch in VLAN 1 needs to be communicate with a device on the same switch is VLAN 2. What should you configure so that the two devices can communicate?
Routing
You are troubleshooting access to a server in a remote network. You use the tracert command and see the following: Trace route to 192.168.2.250 over a maximum of 30 hops: 1 2 ms 2 ms 2 ms 192.168.12.11 2 2 ms 2 ms 2ms 192.168.11.1 3 5 ms 5 ms 3 ms 192.168.10.15 4 2 ms 2 ms 2 ms 192.168.9.1 5 5 ms 5 ms 3 ms 192.168.11.1 6 2 ms 2 ms 2 ms 192.168.10.15 7 5 ms 5 ms 3 ms 192.168.9.1 ...additional output omitted What is the problem?
Routing loop.
What type of module might a switch use to allow it to modify the media type supported by a switch port? (Select two)
SFP GBIC
What protocol sens e-mail to a mail server?
SMTP
Your company has just acquired another company in the same city. You are given the task of integrating the two e-mail systems so that messages can be changed between the e-mail servers. However, each network uses an e-mail package from a different vendor? Which TCP/IP protocol will enable messages to be exchanged between systems?
SMTP
Which of the following network services or protocols uses TCP/IP port 22
SSH
Which of the following network services or protocols uses TCP/IP port 22?
SSH
Which of the following connectors is used with fiber optic cables and connects using a twisting motion?
ST
A switch receives a frame addressed to the MAC address FF:FF:FF:FF:FF:FF. What will the switch do with the frame?
Send it out all ports except for the port it was received on
An 8-port switch receives a frame on port number 1. The frame is addressed to an unknown device. What will the switch do?
Send the frame out port 2-8.
Which of the following forms of optical fiber would usually be used to connect two building across campus from each other, which are several kilometers apart?
Single Mode
You want to implement an Ethernet network at very long distances using fiber optic cables. Which standard and cable type would you choose?(2 answers)
Single Mode Fiber 1000BaseLX
Of the following cables, which offer the best protection against EMI?
Single mode fiber optic
Users report that the Internet is no longer accessible. You suspect that the line connecting your building to the Internet is not working properly. Which of the following allows the service provider to remotely test the local loop?
Smart jack.
You are monitoring network traffic on your network, and you see the traffic between two network hosts on port 2427. What is the source of this network traffic?
Someone is using Voice over IP (VoIP) to make a telephone call.
You are monitoring network traffic on your network, and you see traffic between two network hosts on port 2427
Someone is using Voice over IP VOIP
You have just installed a packet-filtering firewall on your network. Which options will you be able to set on your firewall?
Source address of a packet Destination address of a packet Port Number
You manage a network that uses multiple switches. You want to provide muliple paths between switches so that if one link goes down, an alternate path is available. Which feature should your switch support?
Spanning tree
You manage a single subnet with three switches. The switches are connected to provide redundant paths between the switches. Which feature prevents switching loops and ensures there is only a single active patch between any two switches?
Spanning tree
One method of preventing routing loops is to not send information about a route back to the router from which the information came. What is this technique called?
Split horizon
Which of the following topologies connects each network device to a central hub?
Star
You have a small network that uses a hub to connect multiple devices. What physical topology is used?
Star
Which of the following physical topologies are used with Ethernet networks?(2 answers)
Star Bus
You are the network administrator for a small company that implements NAT to access the Internet. However, you recently acquired 5 servers that must be accessible from outside your network. Your ISP has provided you with 5 additional registered IP addresses to support these new servers but you don't want the public to access these servers directly. You want to place these servers behind your firewall on the inside network yet still allow them to be accessible to the public from the outside. Which method of NAT translation should you implement for these 5 servers?
Static
1. Static Full Assignment 2. Static Partial Assignment 3. Stateless Autoconfiguration 4. Stateful DHCPv6 5. Stateless DHCPv6
Static Full Assignment ... The entire 128-bit address and all other configuration information is statically assigned to the host Static Partial Assignment ... The prefix is statically assigned and the interface ID is derived from the MAC address Stateless Autoconfiguration ... Clients automatically generate the interface ID and learn the subnet prefix and default gateway through the Neighbor Discovery Protocol (NDP) Stateful DHCPv6 ... Provides each client with an IP address, default gateway, and other IP configuration information Stateless DHCPv6 ... Supplies the client with the DNS server IP address only. Does not provide the client with an IP address and does not track the status of each client
You have a small network at home that is connected to the Internet. On your home network you have a server with the IP address of 192.138.55.199/16. You have a single public address that is shared by all hosts on your private network. You want to configure the server as a Web server and allow Internet hosts to contact the server to browse a personal website. What should you use to allow access?
Static NAT
A virtual LAN can be created using which of the following?
Switch
You want to reduce collisions by creating separate collision domains and virtual LANs. Which of the following devices should you choose?
Switch
What device is used to create a physical star topology?
Switch or hub
When configuring VLANs on a switch, what is used to identify VLAN membership of a device?
Switch port
Which of the following statements accurately describes a VLAN ID?
Switches append a VLAN ID to the header of each frame to identify the virtual network to which it belongs.
What problem does the Spanning Tree protocol prevent?
Switching loops from developing when redundant paths are implemented between switches.
Which of the following protocols includes extensive error checking to ensure that a transmission is sent and received without mistakes?
TCP
You are an application developer and are writing a program to exchange video files through a TCP/IP netowrk. You need to select a transport protocol that will guarantee deliery. Which TCP/IP protocol would you implement that provides this capability?
TCP
0.1.2 You have been hired as a network technician for a small corporate network. Today is your first day on the job and you need to familiarize yourself with the network. A new employee will work in Office 2 and you need to complete the workstation in the office. Complete the following tasks in Office 2...
Tasks: Add the monitor to the Office 2 Connect the monitor to the computer using the DVI-D cable Plug in the monitor Connect the keyboard to the computer Connect the mouse to the computer Turn on the monitor and the computer Steps: 1. Click the Hardware button under Office 2 to go to the workstation. 2. To add the monitor to the office, expand the Monitors category on the Shelf. 3. Drag the monitor from the Shelf and drop it on the bench in the office (next to the computer). 4. To connect the monitor to the computer, switch to the back view of both objects. Click the Back button above the monitor. Click the Back button above the computer case. 5. On the Shelf, expand the Cables category. 6. Select the DVI-D to DVI-D cable. 7. In the Selected Component pane, select a DVI-D connector. Drag the connector to the white connector on the back of the computer. 8. In the Selected Component pane, select the unconnected DVI-D connector. Drag this connector to the DVI port on the back of the monitor. 9. To plug in the monitor, select the AC power cable on the Shelf. 10. Drag the cable from the Shelf and drop it onto the AC power port on the back of the monitor. Select the female connector. 11. In the Selected Component window, select the male AC power connector. Drag this connector to the unused power port on the wall plate. 12. Expand the Input Devices category on the Shelf. 13. To add the keyboard to the computer, drag the keyboard from the Shelf and drop it on an empty USB port on the back of the computer. 14. To add the mouse to the computer, drag the mouse from the Shelf and drop it on an empty USB port on the back of the computer. 15. Switch to the front view of the monitor and the computer. Click the Front button above the monitor. Click the Front button above the computer case. 16. Click the power button on the monitor. 17. Click the power button on the computer. The computer startup process begins and you are automatically switched to the startup screen view. Click the Start button and click Computer or Control Panel to explore the capabilities of the operating system simulator. To switch back to the hardware view, click the Office 2 button at the top of the simulator window. 18. Click Done to finish the lab and see the score report.
2.3.3 You work as the IT Administrator for a growing corporate network. You are in the process of creating an iSCSI storage area network (SAN) on the CorpiSCSI server. The server is currently connected to the network using an Ethernet cable. To increase the server's performance, you have decided to replace the existing Ethernet connection with a fiber optic connection. Your task in this lab is to do the following...
Tasks: Connect the LC connector to the SFP module on the switch Connect the ST A connector to the Tx port on the computer Connect the ST B connector to the Rx port on the computer Disconnect the Ethernet cable from the CorpiSCSI server Steps: 1. On the shelf, expand the Cables category. 2. Drag the ST to LC fiber cable to the SFP LC port on the switch. 3. In the Select Connector window, click the LC connector. 4. Click the Back button above the rack to switch to the back view. 5. In the Selected Component pane, drag the ST Connector (A) to the Tx port on the CorpiSCSI server (the bottom server). 6. In the Selected Component pane, drag the ST Connector (B) to the Rx port on the CorpiSCSI server. 7. Disconnect the Cat5e Cable from the CorpiSCSI server. Drag the RJ45 connector from the back of the server to the shelf. Click the Front button above the rack. Drag the highlighted RJ45 connector from the switch to the shelf. 8. Click the Windows icon on the CorpiSCSI's monitor (right-most monitor). 9. In the notification area, right-click the network icon and click Open Network and Sharing Center. 10. Click Change adapter settings 11. Verify that Ethernet 3 is connected to CorpNet.com. 12. Click Done to finish the lab.
2.1.3 You are working on a small office/home office (SOHO) network. You have just signed up for cable Internet access for the network. The cable company has installed the line into your home, and given you a preconfigured modem for your network. Your task in this lab is to...
Tasks: Connect the cable modem to the Internet using the RG-6 cable Connect the computer to the cable modem using the Ethernet cable Plug in the cable modem Confirm that the computer is properly connected to the Internet Steps: 1. On the Shelf, expand the Modems category. 2. Drag the cable modem from the Shelf to the Workspace. 3. To connect the modem to the Internet connection, switch to the back view of the cable modem. 4. On the Shelf, expand the Cables category. 5. Select the RG-6 coaxial cable. 6. In the Selected Component window, drag a connector to the port on the cable modem. 7. In the Selected Component window, drag the other connector to the port on the wall plate. 8. To connect the computer to the cable modem, switch to the back view of the computer. 9. On the Shelf, select the Cat5e Ethernet cable. 10. In the Selected Component window, drag a connector to the Ethernet port on the cable modem. 11. In the Selected Component window, drag the other connector to the Ethernet port on the computer. 12. To plug in the cable modem, select the power adapter on the Shelf. 13. In the Selected Component window, drag the DC power connector to the port on the cable modem. 14. In the Selected Component window, drag the AC adapter end to the power outlet. 15. Click the Windows icon on the monitor. 16. In the notification area, click the networking icon and click Open Network and Sharing Center. The diagram should indicate an active connection to the home network and the Internet.
2.1.3 You are a network technician for a small corporate network. The owner of the company has asked you to connect the new workstation to the network while a new employee is in an orientation meeting. Your task in this lab is to...
Tasks: In Office 1, connect the twisted pair cable between the workstation and the wall plate In Office 1, confirm that the workstation has a connection to the local network and the Internet Steps: 1. Click the Hardware icon shown in Office 1 to go to the workstation. 2. In Office 1, switch to the back view of the computer. 3. On the Shelf, expand the Cables category. 4. Select each cable type. Examine the cable ends in the Selected Component window to identify the cable with RJ- 45 connectors. 5. In the Selected Component window, select a cable end. Drag and drop the connector to the Ethernet port on the computer. 6. In the Selected Component window, drag the other connector to the Ethernet port on the wall outlet. 7. To confirm that the workstation has a connection to the local network and the Internet, click the Windows icon on the monitor. 8. In the notification area, click the network icon and click Open Network and Sharing Center. The diagram should indicate an active connection to the network and the Internet.
2.4.7 You are a network technician for a small corporate network. You recently made a patch panel connection for a workstation in the IT Administrator Office. In order to connect other workstations which you have placed in other offices, you need to connect patch cables between the patch panel and the switch. Your task in this lab is to connect patch cables as indicated in the following table...
Tasks: In the Networking Closet, connect a patch cable between the Exec 1 port on the patch panel and port 1 on the switch In the Networking Closet, connect a patch cable between the Support port on the patch panel and port 6 on the switch In the Networking Closet, connect a patch cable between the Lobby port on the patch panel and port 8 on the switch Steps: 1. In the Networking Closet, expand the Cables category in the Shelf. 2. Select the Ethernet twisted pair cable. 3. In the Selected Component window, drag the connector to the Exec 1 port on the patch panel. 4. In the Selected Component window, drag the other connector to port 1 on the switch (top row, first column on the left). 5. Repeat steps 2 through 4 for the remaining locations.
2.4.6 You are a network technician for a small corporate network. Today you moved an unused workstation to the IT Administration office, and now you need to connect the computer to the Ethernet local area network and the Internet. Your task in this lab is to connect the workstation to the wired network as follows...
Tasks: In the Networking Closet, connect an Ethernet twisted pair cable betweeen the IT Adm port on the patch panel and port 5 on the switch In the IT Administration office, connect an Ethernet twisted pair cable between the workstation and the wall outlet In the IT Administration office, configure the workstation to obtain IP and DNS addresses automatically Steps: 1. In the Networking Closet, expand the Cables category in the Shelf. 2. Select the Ethernet twisted pair cable. 3. In the Selected Component pane, drag the connector to the IT Adm port on the patch panel. 4. In the Selected Component pane, drag the other connector to port 5 on the switch (top row, fifth column from the left). 5. In the IT Administration office, switch to the back view of the computer. 6. Expand the Cables category in the Shelf and select the Ethernet twisted pair cable. 7. In the Selected Component pane, select a cable end. Drag the connector to the Ethernet port on the computer. 8. In the Selected Component pane, drag the other connector to the Ethernet port on the wall outlet. 9. To configure the workstation to obtain IP and DNS addresses automatically from the server on the network, click the Windows icon on the monitor's screen. 10. In the notification area, click the network icon and click Open Network and Sharing Center. (The Network and Sharing Center diagram should indicate a bad connection to the Internet.) 11. Click Local Area Connection. 12. Click Properties. 13. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. 14. Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK. 15. Click Close. 16. Click Close. 17. To confirm the connection to the network and the Internet for the workstation, view the diagram in the Network and Sharing center. The Network and Sharing Center diagram should now indicate an active connection to the local network and the Internet.
0.1.3 You have recently been hired as a network technician for a small corporate network. Today is your first day on the job and you need to familiarize yourself with the network. You need to continue to work on the computer in Office 2 and go to the Networking Closet to test the rack mounted uninterruptible power supply (UPS). Complete the following tasks in Office 2...
Tasks: Install the PCIe network adapter Install the PCI network adapter Turn the computer back on after installing the network adapters Connect the networking cable between the wall plate and the computer In the Networking Closet, remove the power cable from the wall plate Steps: 1. Click the Hardware button under Office 2 to go to the workstation. 2. Click the Motherboard button above the computer case to switch to the motherboard view of the computer. 3. Read the warning and click Yes to turn the computer off. 4. On the Shelf, expand the Network Adapters category. 5. Examine each expansion card. If necessary, click Details to get a larger view of the expansion card. Tip: In the Details window, compare the tab size on the card with the slot on the motherboard. Expansion slots required for this scenario on the motherboard are as follows: PCIe x1 PCI 6. To install a card, drag the card from the Shelf to a free slot on the motherboard. 7. Repeat steps 5 and 6 to install additional expansion cards. 8. To connect the computer to the wall plate, click the Back button above the computer case. 9. Expand the Cables category on the Shelf and select the networking cable. 10. In the Selected Component pane, select a cable end. Drag and drop the connector to any of the network adapter ports on the computer. 11. In the Selected Component pane, drag the other connector to the network port on the wall outlet. 12. To turn the computer on, click the Front button above the computer case. 13. Click the power button on the computer. The computer startup process begins and you are automatically switched to the startup screen view. Click the Start button and click Computer or Control Panel to explore the capabilities of the operating system simulator. To switch back to the hardware view, click the Office 2 button at the top of the operating system simulator. 14. In the Navigation Path, click Floor 1. 15. Click the Hardware button under Networking Closet. 16. Drag the male AC power connector out of the wall plate's AC outlet. 17. Observe the power and activity lights on the rack mounted networking devices to ensure that they are still flickering. (Zoom in if necessary.) 18. Click the Done button to finish the lab and see the score report.
A small startup company has hired
The UTM represents a single point of failure
A small startup company has hired you to harden their new network. Because funds are limited, you have decided to implement a unified threat management (UTM) device that provides multiple security features in a single network appliance: • Firewall • VPN • Anti-spam • Antivirus You join the UTM device to the company's Active Directory domain. The company's traveling sales force will use the VPN functionality provided by the UTM device to connect to the internal company network from hotel and airport public WiFi networks. What weaknesses exist in this implementation?
The UTM represents a single point of failure.
Which of the following is true about single mode fiber optic network cabling?
The central core is smaller than that of multimode fiber optic cabling
A network is connected following the IEEE 802.3 specifications. Which of the following best describes when a device can transmit messages?
The device listens to determine if the transmission media is free.
What information does the next hop entry in a routing table identify?
The first router in the path to the destination network.
Which of the following are true using multiple VLANS on a single switch? select two
The number of broadcast domains increases The number of collision domains remain the same
You are monitoring network traffic on your network and you see a large amount of traffic between a Windows workstation and a Window server on the following ports: *137 *138 *139 Which is the source of this network traffic?
The workstation is using NetBIOS to access shared resources on the server.
While viewing the status of the interfaces on a Cisco switch, you see abnormally large of oversized ethernet frames being received on one interface. This interface is connected to a workstation located on the 2nd floor. What could be causing this to happen?
The workstation's network board is jabbering
What is the primary purpose of gateway redundancy?
To overcome a single point of failure on the next hop router.
Which of the following is a good reason to install a firewall?
To prevent hackers from accessing your network.
Which OSI Model layer is responsible for guaranteeing reliable message delivery?
Transport
You manage a network with two switches. The switches are connected together through their Gigabit Ethernet uplink ports. You define VLAN 1 and VLAN 2 on each switch. A device on the first switch in VLAN 1 needs to communicate with a device on the second switch also in VLAN 1. What should you configure to allow communication between these two devices through the switches?
Trunking
You manage a single subnet with three switches. The switches are connected to provide redundant paths between the switches. Which feature allows the switches to pass VLAN traffic between the switches?
Trunking
What type of cabling is used with 100BaseTX Fast Ethernet networks?
Type 1A STP or Category 5 UTP
Which protocol and port number is used by BOOTP
UDP 67
You are troubleshooting a connectivity problem in which one clien system is unable to connect to a server. Both the server and client system are connected to the same Ethernet network switch. No other users have complained of a problem, and you suspect that faulty network cabling might be to blame. Which of the following troubleshooting steps are you most likely to perform first?
Use a cable tester to test the cable between the computer system and the network switch.
You have a company network that is connected to the Internet. You want all users
Use firewalls to create a DMZ. Web Inside / Private Behind
Match each network signaling method on the left with its corresponding definition on the right.
Uses the entire network medium as a single transmission channel-Baseband Combines signals from multiple channels into a single channel.-De-multiplexing Assigns different frequencies to different channels on the same network medium.-Frequency-division multiplexing Divides the transmission medium into several channels.-Broadband Measures the number of times a signal in a communications channel changes state.-Baud rate Measures the number of data bits transmitted in one second in a communication channel.-Bit rate
You run a small network for your business that has a single router connected to the internet and a single switch. You keep sensitive doc. What should you use for this situation?
VLAN
You manage a network that uses a single switch. All ports within your buildings connect through he single switch . Which feature should you implement?
VLANs
You need to keep users in all other departments from accessing the servers used by the finance department. Which of the following technologies should you use to logically isolate the network?
VLANs
You have a network that occupies all three floors of a building. The WAN service provider has installed the line for the WAN service into the building in a wiring closet on the main floor. You have a wiring closet on the two remaining floors directly above the wiring closet on the main floor. What would you use to connect the wiring closets together?
Vertical Cross Connect
You manage a network with a single switch. On each switch port, a hub connects multiple devices to the switch. which condition are you most likely to experience on the network ?
collisions
You are troubleshooting a connectivity problem on a Linux server. You are unable to connect to another system on the local network, but are not able to connect to a server on a remote network. You suspect that a default gateway information for the system may be configured incorrectly. Which of the following commands would you use to view the default gateway information on a Linux server?
ifconfig.
Which TCP/IP utility gives you the following output? (shows the computer's TCP/IP configuration information)
ipconfig
You want to be able to view the DNS server address that a computer is using. Which of the following utilities would you use?
ipconfig. ifconfig.
Switches running the STP are in the process of exchanging BPDUs and defining their roles. In what state are the switches?
listening
Which TCP/IP utility gives you the following output? Reply from 192.168.1.68: bytes=32 time<10ms TTL=128 Reply from 192.168.1.68: bytes=32 time<10ms TTL=128Reply from 192.168.1.68: bytes=32 time<10ms TTL=128Reply from 192.168.1.68: bytes=32 time<10ms TTL=128 Packets: Sent = 4, Received = 4, Lost = 0 <0% loss>, Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms
ping.
Which of the following commands would display the output shown here?
route print.
Which of the following utilities would you use to view the routing table?
route.
The network board in a workstation is currently configured as follows:
show running-config interface show interface
Which of the following solutions would you implement to eliminate switching loops?
spanning tree
You manage a network that uses multiple switches. You want to provide multiple paths between switches so that if one link goes down, an alternate path is available. Which feature should your switch support?
spanning tree
Which feature prevents switching loops and ensures there is only a single active path between any two switches?
spanning trees
Examine the following output: 4 22 ms 21 ms 22 ms sttlawa01gr02.bb.ispxy.com [154.11.10.62] 5 39 ms 39 ms 65 ms plalca01gr00.bb.ispxy.com [154.11.12.11] 6 39 ms 39 ms 39 ms Rwest.placa01gr00.bb.ispxy.com [154.11.3.14] 7 40 ms 39 ms 46 ms svl-core-03.inet.ispoxy.net [205.171.206.29] 8 75 ms 117 ms 63 ms dia-core-01.inet.ispxy.net [205.151.142.1] Which of the following produced this output?
tracert.
Which TCP/IP utility gives you the following output? 2 14 ms <10 ms 14 ms Loopback0.GWI.SLT1.ALTER.NET [137.39.2.123] 3 14 ms <10 ms 13 ms 122.at-6-0-0.XR1.SLT4.ALTER.NET [152.63.91.86] 4 <10 ms 14 ms <10 ms 0.so-0-1-0.TL1.SLT4.ALTER.NET [152.63.1.210] 5 41 ms 41 ms 41 ms 0.so-7-0-0.TL1.PQR3.ALTER.NET [152.63.32.41] 6 42 ms 41 ms 41 ms 0.so.6-0-0.XL1.SEA1.ALTER.NET [152.63.38.82] 7 41 ms 41 ms 41 ms PQS6-0.GW11.SEA1.ALTER.NET [152.63.107.17]
tracert.
You are the network administrator of a branch office of your company. The branch office network is part of a WAN that covers most of the United States. The office has two Windows 2000 servers, two UNIX severs, one Windows NT server, 90 Windows 98 clients, 40 Windows 2000 Professional clients, and five Macintosh clients. Users have been complaining that they are unable to access resources over the WAN at the main headquarters. You suspect that one of the routers between your office and the main headquarters is not working properly. What TCP/IP utility can you use to see if a router is not working properly?
tracert.
