Autocad prep

Réussis tes devoirs et examens dès maintenant avec Quizwiz!

What is the angle that you use to rotate the chair from point A to point B? A) 90 B) -90 C) -270 D) None

-90

How many types of arcs do we have in AutoCad? A) 10 B) 3 C) 11 D) 12

11

By default, AutoCAD has the following workspaces. A) 2D Drafting & Annotation B) 3D Modeling C) My workspace D) AutoCAD Classic

2D Drafting & Annotation, 3D Modeling, AutoCAD Classic

How many types of islands do we have in Hatch Command? A) 3 B) 4 C) 9 D) 6

3

In order to get the below result using Object A, you have to set the number of rows and columns to: A) 4,1 B) 4,2 C) 4,3 D) 4,4

4,2

How many types of circles do we have in AutoCad? A) 3 B) 6 C) 4 D) 5

6

By mistake, only the hatch object was moved in a drawing revision. Which tool will rectify this situation? A) Recreate B) Pick Points C) Remove D) Select

A

How does Drawing Compare automatically display the differences between drawings? A) Revision Clouds B) Arrows C) Colors D) Hatching

A

If an annotation scale is not assigned to an annotative object but is used in a scaled viewport, what happens to the annotative object? A) It is not displayed B) It is too small C) It is too large D) It is displayed at the incorrect scale

A

Objects are selected in Drawing A. You right-click and choose Copy with Basepoint and specify a basepoint. Upon switching to Drawing B, you right-click and choose Paste as Block. What is the result? A) The selected elements are placed as an unnamed block B) The selected elements are dated as a block and exploded C) The selected elements are placed as individual elements D) The selected elements are Placed as a group

A

Refer to the exhibit. A dashed line needs to be placed that precisely connects the two point objects. Which object snap should be used? A) Intersect B) Center C) Node D) Endpoint

A

Refer to the exhibit. Three multileaders in a drawing (BEFORE) need to be revised to suit the new leader arrangement (AFTER). Which multileader command should you use? A) Collect B) Remove C) Add D) Align

A

Refer to the exhibit. Which area of the interface is used to filter for Line objects in the drawing? A, B, C, or D

A

To represent a circular hole in a 2D isometric View, which command should you use? A) ELLIPSE B) CIRCLE C) SPLINE D) ISOCIRCLE

A

What occurs when an external reference is attached as an overlay in the host drawing and you then use the host drawing where the overlay is attached as an external reference? A) The overlav external reference is not included with the host file B) The overlay external C) Reference is automatically included with the host file D) You are prompted to open the External References palette The overlay external E) Reference is included but shows as "detached"

A

When using the Polyline option in the WIPEOUT command, on which layer will the wipeout be placed? A) Current B) zero C) Defpoints D) Polyline layer

A

When working with xrefs in a drawing, a clipping boundary can be used to manage the display of the xref in the host drawing except for which of the following? A) Circular B) Polygonal C) Rectangular D) Poly line

A

Which command allows you to plot multiple drawings in AutoCAD? A) PUBLISH B) PLOT C) DWFOUT D) DXFOUT

A

You are working with two scaled viewports of differing scales. The dimension annotations in both viewports are the same by way of text height and arrowhead size. Why is this the case? A) The dimension stvle is annotative B) The text style is associative C) The dimension annotatonIs not annotative D)The dimension annotation is associative

A

Refer to the exhibit. You want to use MATCHPROPERTIES to change all the dimension annotation to use the same dimension style and layer. Which properties should you select? (Select two.) A, B, C, D, or E

A and C

Which of the following can be joined using the Join command? A, B, C, and D

A and C

In order to move an object, ________________. A) Select a base point, followed by a point to define where the object is moving to. B) Use the Displacement option. C) Select an object for grips, then move. D) All of the above

All of the above

What is the function of the divide command? A) To Divide Circle in Segments B) To Divide Polyline in Segments C) To Divide Line in Segments D) All of the Above

All of the above

An array is used to place multiple instances of the same object(s). What is the appropriate method of placement for the array objects? A) Along a rav at variable distances B) At set distances C) Along a ray at set distances D) At variable distances

B

Refer to the exhibit. A corner of an object requires a chamfer as shown in the exhibit. Each length (A and B) is different. Which option in the CHAMFER command gives you the desired result? A) No Trim B) Distance C) Trim D) Angle

B

Refer to the exhibit. Oblique angles can be applied to dimensions, especially when working in isometric drafting. Which tool should be used to add oblique dimension angles? (Choose the letter that matches the icon.) A, B, C, or D

B

Refer to the exhibit. Select the letter of the layer control used to change the color of the mark ups later in the current viewport. A, B, C, or D

B

Refer to the exhibit. The exhibit shows a wall line (dashed) that has been offset using the OFFSET command. What option in the OFFSET command is used to achieve the dashed offset line? A) Source B) Current C) Through D) Erase

B

Refer to the exhibit. The arc on the left needs to be modified so that it looks like the arc on the right. Which is the best method to achieve this? A) JOIN command with both arcs B) LENGTHEN with Dynamic option C) Endpoint grip and stretch Fillet with Shift key.

B

To convert a line segment of a polyline into an arc, which part of the polvline should be used? A) Midpoint object snap B) Midpoint grip C) Endpoint gri D) Endpoint object snap

B

To create a polyline with width about its centerline, which variable should be defined? A) Length B) Width C) Global width D) Halfwidth

B

When sending an transmittal using TRANSMIT, the files can be sent as a package. Which package filetype can be used? A) PDF B) ZIP C) RAR D) EXE

B

Which tool allows you to retain and restore the settings of more than one laver at a time? A) Layer Filters B) Layer States Manager C) Layer Properties Manager D) Locked Layer Fading

B

You are working in AutoCAD, and there is an unexpected power outage. Upon powering up AutoCAD again, what tool should you use to check the integrity of the DWG file you were working on? A) AUDIT B) RECOVER C) STATUS D) PURGE

B

You have a drawing with several blocks in it. You want to make sure that the blocks are saved to a separate drive folder as separate DWG files. Which command should be used? A) SAVEAS B) BLOCK C) WBLOCK D) BEDIT

B

After you select the vertex of a six-sided polygon, what multi-grip options are available? (Select three.) A) Remove Vertex B) Stretch C) Extend D) Add Vertex E) Lengthen

B and E

What does the DRAWORDER command allow you to do in the drawing? (Select three.) A) Bring Hatches to Front B) Bring Dimensions to Front C) Bring Leaders to Front D) Bring Text to Front E) Send All Annotations to Back

B, C, and D

Which of the following object types can be converted into a region? (Select three.) A) Line B) Polygon C) Circle D) BLOCK E) Ellipse

B, C, and E

A rectangular boundary encloses a landscaping layout represented by a number of geometric objects. When hatching, the hatch pattern covers all of the obiects within the boundary. Which hatch setting needs to be changed? A) Normal island detection B) Separate hatches C) Ignore island detection D) Outer island detection

C

How do you identify the annotative scale of a text object? A) Double-click on the text object B) Check the text style settings C) Select the object, right-click and select Properties D)Hover over the text object

C

Refer to the exhibit. Blocks not being used in a drawing can be tidied up using the PURGE command, as shown in the exhibit. Which option allows you to check sequentially which blocks are being purged from the drawing? A, B, C, or D

C

Refer to the exhibit. The image below shows a design that has filleted corners but the angled geometry has been left in place. To create fillets without trimming the corner(s), which setting in the FILLET command do you select? A) LEAVE EDGE B) ADD CURVE C) NO TRIM D) NO EDIT

C

Refer to the exhibit. You can move the oriqin of the UCS using grips. Select the appropriate grip you would use to move the UCS shown. A) The Y axis grip B) The X axis grip C) The origin grip D) Another coordinate

C

Symbols from the character map can be inserted into multiline text (MTEXT). Which method should be used to do this? A) Type the character code in the multiline text window B) Insert from a file C) Copy and Paste from the Character map D) Copy and Paste the character code into the multiline text window

C

The Viewports (VPORTS) command allows you to set up viewports in the Model tab and Layout tabs. When a layout is current, which ribbon tab can be used to create and configure viewports? A) Annotate B) Home C) Layout D) Output

C

What occurs when a field is inserted into text? A) It uses the current text stvle. Regardless of what text style is used by the text B) It uses a different text style from the text object C) it uses the same text stvle as the text obiect D) It uses a prompt for a new text style

C

When defining attributes, what attribute mode is used to ensure multiple attributes are ordered neatly in a block? A) Invisible B) LOCK position C) Align below previous attribute definition D) Preset

C

Where are the tools to isolate or hide objects in a drawing located? A) Display bar B) View tap on the ribbon C) Status bar D) Options dialog box

C

Reter to the exhibit. You are working in a layout in paper space. How do you add a custom scale to the scale list? (Select two.) A) Select the viewport B) Double-click to activate the viewport C) Type SCALELISTEDIT D) Use the VPORTS command E) Use the Scale List on the status bar

C and E

Which of the following can hyperlinks be linked to? (Select three.) A) Views inside a drawing B) Links to AutoLISP macros C) Layout tabs in a drawing D) Other software links E) An existing file or webpage

C, A, and E

What is the default method to draw a circle? A) Center Diameter B) Center Radius C) 2 points D) Tan Tan Tan

Center Radius

The multi-leaders 4,8,9 represent: A) Aligned Multileaders B) Vertical Multileaders C) Collected Multileaders D) Horizontal Multileaders

Collected multileaders

An xline is infinite in how many directions? A) Four B) One C) More than one D) Two

D

How do you remove objects from a selection set? A) Press and hold the CTRL key and select the objects to be removed B) Press and hold the Tab key and select the obedis to De removed C) Press and hold the R key and select the objects to be removed D) Press and hold the Shift key and select the objects to be removed

D

Refer to the exhibit. The Text Editor tab allows for the insertion and manipulation of special character types. A specific character is needed to finish item 2 in the roof purlin specification shown. Select the appropriate part of the Text Editor in which vou will need to do this. A, B, C, or D

D

Refer to the exhibit. To ensure dimensions are always placed on the correct layer, you can utilize Dim Layer Override. In which area of the Dimensions panel is this set? A, B, C, or D

D

Refer to the exhibit. When adding new angles to the Polar Tracking list, certain settings have to be verified. Which setting should be used for this to happen? A, B, C, or D

D

Refer to the exhibit. You want to rotate the chair on the left so it looks like the chair on the right (parallel to the desk). Pick the point on the chair that should be used as the basepoint. A, B, C, or D

D

Refer to the exhibit. You use the DIMBREAK tool to create the dimension breaks as shown in the exhibit. What controls the amount of gap applied? A) The dimension properties B) The gap option of the DIMBREAK tool C) The user is prompted for the gap points D) The dimension style

D

Select the appropriate method to rotate a viewport. A) Use the VPROTATE command B) Select the viewport, right-click and choose Properties and change the Angle property C) Rotate the UCS D) Use the ROTATE command

D

There are several blocks named K-1054 in your current drawing. If you create a new block with the same name but with a different appearance, what will occur? A) This is not possible B) The new blocks will update to the existing ones C) The existing blocks and the new blocks will appear different D) The existing blocks update to the new block definition

D

What occurs if no text height is assigned in a text style? A) The text style cannot be annotative B) The text will use the default text height until it is changed C) The text style must be annotative D) You will be prompted for the text height every time you create text

D

What workflow should be used in order to create a corner between two perpendicular lines? A) Use the TRIM command, press the Shift kev and select both lines. B) Use the TRIM command, press Enter, and select one of the lines. Use the EXTEND command, C) Press the Shift key and select both lines. D) Use the FILLET command, select one line, press and hold the Shift key, and select the second line

D

Which properties and settings cannot be changed using the Block Attribute Manager (BATTMAN)? A) The invisibility setting for the attribute B) The default value of the attribute C) The prompt for the attribute D) The transparency of the attribute

D

You can use the ALIGN command to ensure consistent multileader display. What occurs if you align multileaders using the PARALLEL option? A) The arrowheads automatically become parallel to each other B) The landing line segments automatcalv become parallel C) To each other The text/blocks automatically become parallel to each other D) The leader line segments automatically become parallel to each other

D

Which of the following statements are true about grips? (Select three.) A) You cannot select more than one grip B) You can select and move grips to stretch an object C) You cannot use more than one operation when editing with grips D) Grips on text, block references, and midpoints of lines move the object rather than stretching it E) Press Enter or Spacebar to cycle to the move, rotate, scale, or mirror grip modes

D and E

What is the command used to draw the above dimension line? A) Dimjogged B) Dimjogline C) Joggeddim D) Joggedline

DimJogline

Which of the following breaks a compound object into its component objects? A) Explode B) Breaks at Point c) Break D) All Above

Explode

Function of ____________________ is to draw a straight line. A) odnap B) f4 c) f8 D) None of these

F8

Using the Purge command, we can purge referenced blocks. True/False? A) true B) false

False

When you use the Match Properties command, you can select multiple source objects. True/False? A) True B) False

False

With the help of ____________________ we can Rounds and fillets the edges of objects. A) Chamfer B) Blend Curve C) Fillet D) None of these

Fillet

Which of the following settings can be made for polar tracking? A) Increment angle B) Additional angles C) Track using all polar angles settings

Increment angle, Additional angles

With the Multiline Text editor, you can do all of the following, except: A) Insert numbered and bulleted lists B) Insert specific drafting and engineering symbols C) Insert pictures D) Create Fields such as date, time, and author.

Insert pictures

with which of the following tool, a straight line segment can be created? A) Spline B) Polyline C) Line D) All of the above

Line

The following are some of the properties and settings that you can save in a layout, except _____________. A) Plot scale B) Paper size C) Line weight D) Drawing orientation

Line weight

Which options are used to draw this polyline? A) Line B) Arc C) Tamper D) Width

Line, Arc, width

If you need the text to be reversed, when you mirror the text, then you need to set: A) MIRRTEXT to 0 B) MIRRTEXT to 1 C) TEXTMIRR to 0 D) TEXTMIRR to 1

MIRRTEXT to 1

One of the below options is wrong about the type of AutoCad drawing units. Which one is it? A) Architectural B) Engineering C) Millimeter D) Decimal

Millimeter

____________________creates a mirrored copy of selected objects? A) Copy B) offset C) mirror D) All above

Mirror

With a hot grip, which of these editing tasks can you perform? A) Move B) Offset C) Rotate D) Scale

Move, rotate, scale

You can set viewport scale factor by _______________. A) Typing vscale B) Typing vpscale C) Typing viewportscale D) None

None

What type of Island detection type is this? A) Inner B) Outer C) Ignore D) Normal

Normal

Which of the following is the short key for Rectangle? A) R B) Rac C) Rec D) Pol

Rec

With the help of which of the following tool the object in a row and column be arranged? A) Polar Array B) Rectangular Array C) Path Array D) All Above

Rectangular Array

Which of the following enlarges or reduces selected objects, keeping the proportions of the object the same after scaling? A) Scale B) Stretch C) Polyedit D) All of the Above

Scale

Object snap tracking works in combination with object snaps to enable you to temporarily acquire and track up to how many points? A) One B) Two C) Five D) Seven

Seven

What happens if you fillet these two lines with the radius of 0? A) Cannot fillet B) Sharp corner C) None

Sharp corner

A hatch object displays a standard pattern of lines and dots used to highlight an area, or to identify a material, such as steel or concrete. A) true B) false

True

Copy command also creates Multiple copies of an object. True/False? A) True B) False

True

If you copy and paste text from another drawing or insert a block into a drawing that has the same Text Style name with different properties, the text properties of the host drawing will take precedence. True/False? A) true B) false

True

If you modify a dimension style, all dimensions using that style in the drawing update automatically. True/False? A) true B) false

True

Using object snaps to select points for Inquiry commands is Critical. A) True B) False

True

When using copy with grips, select copy after you have selected an option, such as Move, Mirror, Rotate, Scale, or Stretch. True/False? A) True B) False

True

When you Explode a block, the geometry returns to its original properties. True/False? A) true B) false

True

You cannot fillet or chamfer the first segment of a polyline with the last segment of the same polyline. True/False? A) true B) false

True

What happens when you set VPROTATEASSOC System Variable to 0? A) When a viewport is rotated, the view inside is not rotated. B) When a viewport is rotated, the view inside is rotated to match the rotation of the viewport.

When a viewport is rotated, the view inside is not rotated.

By selecting which one of the following, the objects on the layer are not visible and are not considered when the drawing is regenerated? A) When you off the layer B) When you froze the layer C) When you lock the layer D) None

When you froze the layer

Which of the following is the Short key of Insert Block? A) W B) B C) Xref D) i

i

Which Key do you press to cycle through the available snap points? A) Ctrl B) Shift C) Tab D) Alt

tab


Ensembles d'études connexes

Pharmacology Prep U Level 1-4 Chapter 47 Lipid Lowering Agents

View Set

Texas Principles of Real Estate 1 - Chapter 1

View Set

GBA 1 - Assignment 5 - Consumer-Driven Health Plans

View Set

B Law Legality & Public Policy Ch. 16 Module 13

View Set

Quiz: Module 11 Security in Network Design

View Set

PrepU exam I Professional Nursing

View Set

AMSCO Chapter 20-25 quiz questions

View Set