ICND1 - 12. Introducing IPv6

Réussis tes devoirs et examens dès maintenant avec Quizwiz!

How are ICMPv6 packets identified in the Next Header field?

ICMPv6 packets are identified as 58 in the Next Header field.

What features does OSFPv3 add?

Open Shortest Path First version 3 (OSPFv3) is based on the current version of OSPF for IPv4, which is version 2. Like version 2, OSPFv3 sends Hellos to neighbors, exchanges link-state advertisements (LSA), and exchanges database descriptor (DBD) packets. However, OSPFv3 runs directly over IPv6 and advertises using multicast groups FF02::5 and FF02::06, but uses its link-local address as the source address of its advertisements. FF02::5 is the address listened to by "all OSPF routers," and FF02::06 is the address listened to by the OSPF DRs and BDR. Note OSPFv3 does not include authentication because authentication in IPv6 is handled through IPsec.

Besides a larger address space, what are some additional benefits of IPv6 when compared to IPv4?

Some additional benefits of IPv6 when compared to IPv4 are as follows: Simplified header Autoconfiguration Enhanced multicast support Extension headers Flow labels Security and mobility built in Improved address allocation Strict aggregation

Before you can forward IPv6 addresses on router interfaces, what must you enable?

You must enable IPv6 unicast routing. By default, IPv6 is not enabled on a Cisco router. As such, before you can forward IPv6 addresses on router interfaces, you must enable IPv6 routing by issuing the ipv6 unicast-routing global command.

What IOS command displays all IPv6 routes entered in the routing table?

The show ipv6 route command displays all IPv6 routes entered in the routing table.

What is an IPv6 multicast address?

An IPv6 multicast address identifies a set of devices called a multicast group. It has a one-to-many mapping and also replaces IPv4 broadcast addresses. IPv6 multicast addresses use the reserved address space FF00::0/8.

What is an IPv6 unicast address?

An IPv6 unicast address is an address that identifies a single device. It has a one-to-one mapping. Unicast addresses include global, link local, loopback (::11), and unspecified (::).

What is a global unicast address?

A global unicast address is a unicast address that is globally unique and can be routed globally. RFC 4291 specifies 2000::/3 to be reserved as global unicast address space to be allocated by the IANA.

What is a link-local unicast address?

A link-local unicast address is an IPv6 address whose address is confined to a single physical link. Thus the address is not routable off the physical subnet. Link-local addresses typically begin with FE80. The next digits can be assigned manually. If the interface ID is not assigned manually, it can be based on the interface MAC address. Note An interface can have multiple link-local and global addresses.

How many bits are in an IPv6 address?

An IPv6 address is 128 bits long and is represented in eight 16-bit hexadecimal segments. An example of an IPv6 address is as follows: 2001:0D02:0000:0000:0000:C003:0001:F00D

What is an IPv6 anycast address?

An IPv6 anycast address is an address that represents a group of devices that support a similar service. Each device will be assigned the same anycast address. Routers will deliver data to the nearest node that is used in the common anycast address. Anycast addresses have a one-to-nearest mapping. To assign an anycast address to a router interface, configure a global unicast address with the keyword anycast appended to the end of the command line.

What are the three ways that an IPv6 host can be assigned an address?

An IPv6 host can be assigned an address statically, with stateless autoconfiguration, or by Dynamic Host Configuration Protocol version 6 (DHCPv6). Note Hosts use stateless autoconfiguration by waiting for a router to advertise the local prefix. If the end system has a 48-bit MAC address, the host inverts the global/local bit (bit 7) and inserts 0xFFFE in the middle of the MAC address. This is called the EUI-64 address, and it is joined to the prefix to form the IPv6 address.

In IPv6, what is neighbor discovery?

Neighbor discovery in IPv6 is used for router and neighbor solicitation and advertisements, and for redirection of nodes to the best gateway. It performs the same functions as ARP in IPv4. These functions include Determining the link layer address of a neighbor Finding neighbor routers on a link Querying for duplicate addresses Note Neighbor discovery is performed using ICMPv6 with a multicast address.

Does OSPFv3 require an IPv4 address for the router ID?

No. OSPFv3 does not require an IPv4 address for the router ID; however, a 32-bit number must be set for the router ID. When a router has not been configured with an IPv4 address to be used by OSPFv3 for purposes of the router ID, the OSPFv3 process will not immediately start. The required step to then start the OSPF process will be to manually configure the router ID using the router-id router-id command. The value entered into the router-id command will use the format of a normal IPv4 address. However, it is not actually an IPv4 address nor does it need to be configured on an interface of the device.

What is RIPng?

RIPng is the IPv6 version of Routing Information Protocol (RIP), a distance vector protocol. RIPng is defined in RFC 2080 and is based on RIPv2. Thus RIPng uses hop count as its metric and has a maximum hop count of 15. However, some changes to RIPng are as follows: Uses IPv6 for transport. Uses multicast group FF02::09 to advertise routes every 30 seconds. Updates are sent on User Datagram Protocol (UDP) port 521.

What are the two rules for reducing the size of written IPv6 addresses?

The two rules for reducing the size of written IPv6 addresses are as follows: Rule 1: The leading 0s in any fields do not have to be written. If a field has fewer than four hexadecimal digits, it is assumed that the missing digits are leading 0s. For example, 2001:0D02:0000:0000:0000:C003:0001:F00D can be written as follows: 2001:D02:0:0:0:C003:1:F00D Rule 2: Any single, consecutive fields of all 0s can be represented with a double colon. For example, 2001:D02:0:0:0:C003:1:F00D can be further reduced to the following: 2001:D02::C003:1:F00D Note The double colon can be used only once.

In IPv6, what is stateless autoconfiguration?

Stateless autoconfiguration is a feature in IPv6 that uses neighbor discovery to find routers, and it will also dynamically create an IPv6 address based on a prefix found in the router advertisement and EUI-64 standard. When stateless autoconfiguration is enabled on the interface, additional addresses will also be assigned to the interface, one of these being a link-local unicast address.

How do you configure IPv6 static routes?

Static routing with IPv6 is configured the same way as with IPv4. The ipv6 route ipv6_network/ipv6_mask outgoing_interface/ipv6_next_hop global command adds static routes to a router. The following example configures a static route for network 2001:DB8:123::/48 to route traffic to interface serial 0/0: Router(config)# ipv6 route 2001:DB8:123::/48 serial 0/0

What is the EUI-64 standard?

The EUI-64 standard explains how to stretch 802.3 MAC addresses from 48 to 64 bits by inserting the 16-bit 0xFFFE at the 24th bit of the MAC address to create a 64-bit unique identifier. Secondly, the universal/local (U/L) flag (bit 7) in the OUI portion of the address is flipped from 0 to 1 so that 1 now means universal. The EUI-64 standard is used to allow a host to automatically assign itself a unique 64-bit IPv6 address without the need for manual configuration or DHCP. For example, MAC address 00-AA-11-17-FC-0F on the network 2001:0DB8:0:1::/64 becomes 02-AA-11-17-FC-0F. The resulting EUI-64 address on the network is 2001:0DB8:0:1:02AA:11FF:17FE:FC0F.

What are the IPv6 addresses that are reserved by the IETF?

The IETF reserved approximately 1/256 of all the total IPv6 address space. The reserved addresses are The lowest address within each subnet prefix (the interface identifier set to all 0s) is reserved as the "subnet-router" anycast address. Within each subnet, the highest 128 interface identifier values are reserved for the subnet anycast addresses.

What is the address used for the IPv6 loopback address?

The address used for the IPv6 loopback address is 0:0:0:0:0:0:0:1, which is normally expressed as ::1.

How do you configure OSPFv3 on a Cisco router?

The commands to configure OSPFv3 on a Cisco router are as follows from global configuration mode: ipv6 ospf process-id area area_id interface command enables OSPFv3 routing on the interface. ipv6 router ospf process_id enables the OSPFv3 routing process and enters the routing process configuration mode. router-id router-id sets the OSPFv3 router ID with a 32-bit number. The following example configures OSPF with process ID 10 and 0.0.0.2 as the router ID, and enables OSPF on gigabit interfaces g0/0 and g0/1, assigning them to area 0: Router(config)# ipv6 router ospf 10 Router(config-rtr)# router-id 0.0.0.1 Router(config-rtr)# interface g0/0 Router(config-if)# ipv6 ospf 10 area 0 Router(config-if)# interface g0/0 Router(config-if)# ipv6 ospf 10 area 0

What are the eight fields contained in IPv6?

The eight fields in IPv6 are as follows: Version: 4-bit field; contains the number 6. Traffic Class: 8-bit field that is similar to the IPv4 ToS field. Flow Label: New 20-bit field used to mark individual traffic flows with unique values. Payload Length: Describes the length of the payload only. Next Header: Used to determine the type of information that follows the IPv6 header. Hop Limit: Specifies the maximum number of hops that an IP packet can traverse. Source Address: 128-bit (16 octets) identifying the source of the packet. Destination Address: 128-bit field identifying the destination of the packet.

What IPv4 headers were removed in IPv6 headers and why?

The following IPv4 headers were removed in IPv6: Internet Header Length: Removed because all IPv6 headers are a fixed 40-byte length, unlike IPv4. Flags: Used in fragmentation, and IPv6 routers no longer process fragmentation. Fragmentation Offset: IPv6 routers no longer process fragmentation. Header Checksum: Removed because most data link layer technologies already perform checksum and error control. Identification: No longer needed based on IPv6 implementations. Padding: Because the Options field was changed, the Padding field is no longer needed.

Because IPv6 uses a 128-bit address, routing protocols need to be modified to support IPv6. What routing protocols support IPv6?

The following routing protocols support IPv6: RIPng OSPFv3 EIGRP for IPv6 Intermediate System-to-Intermediate System (IS-IS) for IPv6 Multiprotocol Border Gateway Protocol (MP-BGP) Note Although not a routing protocol, IPv6 also supports static routing.

What are the functions of ICMPv6?

The functions of ICMPv6 are Diagnostic tests: Like ICMPv4, ICMPv6 provides diagnostic tests using echo and echo reply. Router discovery: Router solicitation and router advertisements. Neighbor discovery: Neighbor solicitation and neighbor advertisements.

What Cisco IOS command configures a router interface for stateless autoconfiguration?

The ipv6 address autoconfig interface command configures a router's interface for stateless autoconfiguration.

After enabling IPv6 on the router, how would you configure an IPv6 address to an interface?

The ipv6 address ipv6-address/ipv6-length [eui-64] interface command configures an IPv6 address to a router interface.

What is contained in the router solicitation message?

The router solicitation messages contains the following: ICMP type of 133 The source address is unspecified or :: Destination address is the all-routers multicast address FF02::2

What are the three types of IPv6 addresses?

The three types of IPv6 addresses are as follows: Unicast Anycast Multicast

What two message types does ICMPv6 use?

The two message types that ICMPv6 implements are Error messages: Examples include Destination Unreachable, Packet Too Big, or Time Exceeded Informational messages: Echo Request and Echo Reply

How do you configure an IPv6 default route on a Cisco router?

To configure a default IPv6 route on a Cisco router, use the ipv6 route global configuration command with ::/0 specified as the ipv6_network/mask. The following example configures a default route to send all traffic to interface serial 2/0: Router(config)# ipv6 route ::/0 serial 2/0


Ensembles d'études connexes

Module 2 Content Activities (3370)

View Set

Le droit privé du droit aérien

View Set

Simulated Exam Questions Chapter 18-24

View Set

Unit 4: Hola, ¡estoy bien! (Hi, I'm well!)

View Set

Unit Test: Periodic Table Locations+Characteristics (Halogens, Metals, Alkali Metals, etc.)

View Set

Dental School Interview Questions

View Set

Managerial vs. Financial Accounting

View Set

Module 5 : Do We Think Like Computers?

View Set

Marketing (Chapter 7) Market Segmentation

View Set