NETWORK Final

Réussis tes devoirs et examens dès maintenant avec Quizwiz!

Which three factors should be considered when choosing the appropriate network media? (Choose three.) 1.the speed of the CPU and amount of memory in servers 2.the environment in which the media is installed 3.the data security and fault tolerance requirement 4.the amount of data and the data transfer rate desired 5.the distance between hosts that the media will connect 6.the operating systems used on network devices in the network

-the environment in which the media is installed -the amount of data and the data transfer rate desired -the distance between hosts that the media will connect Several criteria should be considered when selecting network media: The cost of the media and installation The environment in which the media is installed The amount of data and the data transfer rate desired The distance between hosts that the media will connect

Which IP address is a unicast address if a default subnet mask is used? 201.34.45.0 192.16.43.67 226.34.15.78 195.124.45.255

192.16.43.67 The IP addresses 201.34.45.0, 192.16.43.67, and 195.124.45.255 are Class C addresses. With the default subnet mask of 255.255.255.0, 192.16.43.67 is a unicast address or host address, 195.124.45.255 is a broadcast address, and 201.34.45.0 is a network address. IP address 226.34.15.78 is a Class D multicast address.

Which three IP addresses are considered private addresses? (Choose three.) 10.234.2.1 128.37.255.6 172.17.254.4 172.68.83.35 192.168.5.29 198.168.6.18

192.168.5.29 10.234.2.1 172.17.254.4 The designated private IP addresses are within the three IP address ranges: 10.0.0.0 - 10.255.255.255 172.16.0.0 - 172.31.255.255 192.168.0.0 - 192.168.255.255

What is the full uncompressed representation of the IPv6 address 2001:DB8:0:0:AA::200? 2001:0DB8:0000:0000:00AA:0000:0200:0000 2001:DB80:0000:0000:AA00:0000:0000:0200 2001:0DB8:0000:0000:00AA:0000:0000:0200 2001:0DB8:0000:00AA:0000:0000:0000:0200

2001:0DB8:0000:0000:00AA:0000:0000:0200 An IPv6 address is made up of 128 bits represented in hexadecimal numbers.There are two rules that help reduce the number of digits needed to represent an IPv6 address. Rule 1 - Omit leading zeros in any 16-bit section. Rule 2 - Replace any single group of consecutive zeros with a double colon (::). This can only be used once within an IPv6 address.

How much data can be encapsulated into a normal sized Ethernet frame before it is sent over the network? 0 to 1024 bytes 32 to 1500 bytes 46 to 1500 bytes 64 to 1518 bytes

46 to 1500 bytes According to the Ethernet standards, each Ethernet frame can carry 46 to 1500 bytes of user data. During the encapsulation process, other fields are added, such as destination MAC address, source MAC address, and FCS. The size of Ethernet frames is normally limited to a maximum of 1518 bytes and a minimum of 64 bytes.

Which scenario describes a peer-to-peer network? Users access shared files from a file server. A user visits a webpage on the company web site. A user has shared a printer attached to the workstation. Users print documents from a network printer that has a built-in NIC.

A user has shared a printer attached to the workstation. In a peer-to-peer network there is no centralized or dedicated server. A user computer can be a client to request service from another user computer and a server to share a network resource (such as a printer) to other users.

What is the difference between the terms bandwidth and throughput? Bandwidth is measured with Mb/s and throughput is measured in Kbps. Bandwidth is the capacity of data transfer in a network and throughput is the actual data transfer rate. Bandwidth measures data transfer of web applications and throughput measures data transfer of video applications. Bandwidth represents the data transfer rate in a local network and throughput represents the data transfer rate over the Internet.

Bandwidth is the capacity of data transfer in a network and throughput is the actual data transfer rate. Both bandwidth and throughput are the measurement of data transfer over a period of time. They use the same measurement units. However, bandwidth is used to indicate the theoretical capacity of a network connection whereas throughput is used to indicate the actual data transfer rate between two hosts at the time of measurement.

A user types http://www.cisco.com into a web browser to visit the corporate website. Which service will resolve the domain name to an associated IP address? FTP DNS DHCP SMTP

DNS When a user types a domain name to visit a website, the DNS service is called to resolve the domain name to its associated IP address before the user packet is sent to the website.

Which two types of interference may affect the data throughput on UTP cables? (Choose two.) EMI noise moisture crosstalk temperature

EMI Cross Talk Unshielded twisted-pair (UTP) cabling is sensitive to the interference introduced by electromagnetic interference (EMI) and crosstalk

Which three configuration components are required to allow a host to communicate with other hosts on remote networks? IP address DNS server subnet mask domain name default gateway DHCP server address

IP Address Subnet Mask Default Gateway An IP address, a subnet mask, and a default gateway are required on a host that must communicate with another host in a remote network. DNS server information is needed if mapping a domain name to an associated IP address. DHCP server information is dynamically learned and is not a required configuration for remote network reachability

Which statement describes a MAC address? It is 128-bits in length. It contains two portions, the network portion and the host portion. It is a physical address assigned to an Ethernet NIC by the manufacturer. It identifies the source and destination addresses of hosts on the Internet.

It is a physical address assigned to an Ethernet NIC by the manufacturer The Media Access Control (MAC) address is a physical address assigned to each Ethernet NIC by manufacturers. It is 48-bits in length. The MAC address is used to identify the source and destination on a local Ethernet network. It cannot be routed to remote networks.

When a host sends a packet, how does it determine if the destination of the packet is on the same local network or on a remote network? It checks to see if the default gateway is configured. It compares the source and destination MAC addresses. It queries the DNS server with the destination IP address. It uses the subnet mask to compare the source and destination IP address.

It uses the subnet mask to compare the source and destination IP address. When a host sends a packet, it uses the subnet mask to compare the source IPv4 address and the destination IPv4 address. If the network bits match, both the source and destination host are on the same local network. Otherwise, the destination host is on a remote network.

Which wireless technology is used on smart phones to transmit data to another device within only very close proximity? NFC Wi-Fi 3G/4G Bluetooth

Near Field Communications (NFC) is a wireless technology that enables data to be exchanged by devices that are in very close proximity to each other.

A user opens multiple windows on the desktop with several tasks including web surfing, emailing, and Skype calling. What is used by the TCP/IP protocol stack to track the specific sessions for each application? port number destination IP address Hypertext Markup Language domain name to IP address resolution

Port Number A user may request different services from the same server or different servers. TCP and UDP port numbers are used to keep track of specific sessions between a client and server.

Which three devices are considered intermediate devices in a network? (Choose three.) router server switch workstation network printer wireless access point

Router Switch Wireless Access Point Intermediate devices in a network provide network connectivity to end devices and transfer user data packets during data communications.

Which transport layer protocol provides best effort delivery without guaranteeing that packets arrive at the destination? SSH TCP UDP HTTP

UDP User Datagram Protocol (UDP) is a best effort transport layer protocol. Unlike TCP, it does not use an acknowledgment protocol to ensure reliable packet delivery. TCP provides reliable delivery service. HTTP and SSH are application layer protocols in the TCP/IP model.

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. What is the code displayed on the web page? Correct Success Welldone Configured Right

Welldone The IP address configuration on PC0 requires the following: IP address - any valid host address on the LAN, except for .254 Subnet mask - default value for the network Gateway - the nearest router interface DNS - the DNS server on the ISP network

Which statement defines a data communications protocol? an alliance of network device manufacturers a set of rules that govern the communication process a set of product standards for types of network devices an exchange agreement of network devices among vendors

a set of rules that govern the communication process A data communication protocol is a set of rules that govern the communication process.

What is an example of a binary value from everyday life? room temperature a simple light switch speed of a traveling car brightness of a light bulb

a simple light switch A binary digit (or bit) has two possible values, 0 or 1. The on and off state of a simple switch is an example of the two states represented by a bit.

A client is sending a message to request information from a web server on the Internet. Which parameter is used in the message to indicate the specific service requested? source port destination port server domain name destination IP address

destination port When clients send requests for a service from a server, the destination port number is used to indicate the specific service requested.

Which two devices are shared peripherals? tablet laptop scanner printer touch-pad with digital stylus

scanner printer A shared peripheral device does not connect directly to a network. This device is attached to a host (such as a PC) and the host connects to the network to share the peripheral device.

What information does an Ethernet switch examine and use to build its address table? source IP address source MAC address destination IP address destination MAC address

source MAC address An Ethernet switch examines the source MAC address of an incoming frame. If the source MAC address is not in the MAC address table, the switch will add it to the table with the associated ingress Ethernet port.

Which factor classifies a host as a server? the CPU speed the software installed the amount of memory the network connection

the software installed server is a host with server software installed. Although CPU, memory, and the network connection will determine the performance of a server, it is the server software that provides desired server services.


Ensembles d'études connexes

Energy Flow in Ecosystems Chapter Test Review

View Set

Strategic Management-Chapter 2 (CAP)

View Set

NU141- Chapter 18 Vaccines and Sera

View Set