Test out

How does standby preemption affect the router configured with the highest priority in the HSRP group? (Select two.)

If the active router fails, but then regains service, it becomes the active router again if preemption is enabled. If the active router fails, but then regains service, it does not become the active router again when preemption is not enabled.

Which of the following are reasons to configure VLANs on a switch as opposed to using switches without VLANs? (Select two.)

Increased security Increased number of broadcast domains

You have configured inter-VLAN routing on a Catalyst 3550 switch. You enter the show run command and receive the output as shown in the exhibit.Which of the following is true? (Select two.)

Interface VLAN 2 is enabled with the no shutdown interface configuration command Traffic sent from VLAN 2 to VLAN 3 will not reach VLAN 3

Which of the following does not accurately describe the HSRP states?

Learn is when the router has received the virtual IP address from a hello message sent by the active router

You have two switches connected together as shown in the following diagram. How many broadcast domains are there in the network shown?

2 Broadcast domains

Which of the following is required before you can create an SVI?

A VLAN must be creatd in the vlan database

Which of the following best describes the various HSRP group roles? (Select two.)

An active router forwards traffic destined to the virtual IP address A standby router will become the active router should the existing active router fail.

Computers A and B are on the same VLAN and are separated by two switches, as shown in the Exhibit. Computer A sends a frame to Computer B. Which of the following best describes the composition of the frame as it travels from A to B?

Computer A sends a normal frame. The first switch appends a VLAN ID to the frame. The second switch removes the VLAN ID before forwarding it to Computer B.

You have two VLANs and two Cisco 1841 routers as shown in the exhibit.How can you configure HSRP to share the load from the two VLANs? (Select two.)

Configure RouterB to serve as the active router for VLAN 4 and the backup router for vlan 2 Configure RouterA to serve as the active route for VLAN 2 and he backup router for VLAN 4

Which of the following are true regarding using multiple VLANs on a single switch? (Select two.)

The Number of broadcast domains increases The number of collision domains remains the same.

You have two routers that should be configured for gateway redundancy. The following commands are entered for each router: A(config)#int fa 0/2 A(config-if)#ip address 172.16.1.2 A(config-if)#standby 2 priority 150 A(config-if)#standby 2 ip 172.16.0.1 B(config)#int fa 0/2 B(config-if)#ip address 172.16.1.3 B(config-if)#standby 2 priority 150 Which of the following is true? (Select two.)

The virtual Ip address is 172.16.0.1 Router B will serve as the active router, and Router A will serve as the standby router.

You have configured inter-VLAN routing on a Catalyst 3550 switch. You enter the show ip route command and receive the output as shown in the exhibit.Which of the following is true? (Select two.)

VLAN 11 has a virtual p address in the 10.1.11.0 network Traffic sent within vlans 2,3, and will be routed on the 3550 switch.

You have configured inter-VLAN routing on a Catalyst 3550 switch. Hosts belonging to VLAN 2 cannot contact servers belonging to VLAN 3. To troubleshoot the issue, you enter the show ip route command and receive the output as shown in the exhibit.Which of the following may be true? (Select two.)

VLAN 2 does not have an interface IP address The VLAN 2 interface is not enabled with the no shutdown command.

Which of the following protocols provide gateway redundancy? (Select all that apply.)

VRRP HSRP

You want to verify that interface fastEthernet 0/2 is a member of VLAN0002. Which command displays the output shown here? VLAN Name Status Ports---- --------------------- --------- -------------------------------1 default active Fa0/3, Fa0/4, Fa0/5, Fa0/6,Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12, Gi0/1, Gi0/22 VLAN0002 active Fa0/2 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active... output suppressed)

show vlan biref