woods
When making a rip or crosscut, the blade should extend no more than ___ inches above the stock
1/4
never raise the saw blade more than ____ inch above the material being cut
1/4
never plane lumber less than ____ thick
1/4 inch
work pieces shorter than ___ inches can not be ripped on the table saw
12
stock less than _____ inches in width will always require the use of a push stick to push the material across the jointer
4"
Hands and fingers should never come closer than ____________ to the rotating blade when operating the motorized miter saw
5 inches
make as many _____ as needed to complete operation
cuts
place a piece of scrap wood under your work piece at the _______ to limit tear out
drill press
do not joint lumber with extremely rough or irregular ____
edges
disconnect the __________ service in the circuit break before making any service adjustment to a machine or power
electrical
never joint the ____ of stock
end
securely ____ stock before using portable power tools
fasen
always hold the material ________ against the miter head to prevent vibration
firmly
always use the ______ when crosscutting
gage
feed lumber into the planer with the ____ of the wood
grain
make certain all _______ are in place and securley fastened
guards
make certain the saw _______ splitter (if available with the guard),anti-kickback device and push stick are used for all possible saw operations
guards
Keep ___ away from moving partrs
hands
keep ____away from any moving parts
hands
set table ______ and bit _______ before starting the drilling operation at the drill press
height , depth
Never look around, carry on a conversation, or "____" while using the planer.
horseplay
never look around, carry on a conversation, or " _____" while using the planer
horseplay
make sure the work piece has a _______ edge
jointed
make sure all stock is free 0f ____,paint,varnish,____,nails,dirt,and grease
knots, staples
position the ____ hand so it is not in direct line with the saw blade
left
use the _____ table slot for the miter gauge and stand to the _____ off the blade when cross cutting
left
when crosscutting table saw operations should work on the _______ side of the saw blade
left
hold the stock against the miter head with the ___ hand and use the _____ hand to advance the miter saw gauge and material through the cut
left , right
never attempt to the rip fence when blade is _______
moving
_____ joint the end of stock
never
when finished working at a machine, turn the machine ______ and wait until all moving parts have _____ before leaving the work area
off, stopped
gloves should not be worn when ______ machines and power tools
operating
never reach _____ the saw blade to remove or hold down a piece of stock.
over
do not _____ the capacity of a tool or machine allow the machine to do the ____
overload,work
get ______ from instructor before making specialty cuts.
permission
wear a _________ or good quality dust mask when using power tools or machines that create a large volume of airborne ____
respirator,dust
before making _______ cuts, align and lock the rip fence in position. the fence should be set to the _______ of the saw blade
rib, right
use the ____ hand to hold the board against the fence and table while using the ____ hand to push the material through the saw
right, left
always align the saw blade on the _____ side of the cut line
scrap
make trial cuts on _____ material before attempting final cuts to make sure the tool/machine is working properly and is set accurately
scrap
keep the work area free from _____, sawdust, and other material hazards
scraps
keep the blades and knives ___ dull blades and knives are more likely cause ____
sharp, kickback
never attempt to surface lumber that is _______ than the distance between the infeed and outfeed rollers( green planer = 15 inches)
shorter
always have the cutterhead _______ in place when jointing.
squared
use a try square to determine if the fence is _______ to the table
squared
never _____ directly behind a machine when it's in operation
stand
always use an approved push_____ or push _____ when jointing stock that does not provide a distance of safety for your hands
stick,block
______ oversized stock while sawing
support
be sure to ________ long and wide stock when sawing.
support
use a helper or a _________ to off- bear the work piece off-bearer only supportd and moves with the stock
support stand
make sure the _____ is in the off position before using hand held power tools.
switch
make sure portable machines are securely attached to a ____ or base support
table
check the blade periodically for missing _______ and cracks
teeth
feed only boards of similar _____ through the planer at the same time. kickbacks can occur while attempting to surface stock of differing thickness
thickness
do not attempt to cut severey _____ lumber
warped
set the rip fence for desired ______ of cut using the scale on the front rail
width
when saw _________ are changed, make certain the blade arbour nut is tightened securely
blades
____ toe shoes should be worn at all times
closed
before operating a machine or tool, confine all loose _____ and long ____
clothes, hair
wait until the blade comes to a ______ stop before removing ____ from the cutting zone
complete, scrap
make sure the electrical ____ and plug are in good operating order
cord
always push the work piece completely past the _____ at the end of a cut to reduce the possibility of _____
blade, kickback
use industrial quality ___ and ____ protection
Ear, eye
Use a helper or a _______ to off-bear the work piece =. An off-bearer
Support stand
maintain your ____ when operating all machine not overreach or use excessive _____ to perform any operation establish a comfortable position prior to starting
balance, force
never stand ____ a piefve of lumber being planed, as kickbacks can cause serious energy
behind
always push the work piece completely past the ______ at the end of a cut on the tablesaw to reduce kickback
blade
stand to one side of the ________ when cutting; do not allow others to stand in direct line with the ______ while the saw is operating
blade
