chapter 4

अब Quizwiz के साथ अपने होमवर्क और परीक्षाओं को एस करें!

The output shaft is also called the ______ shaft.

main

The speed gears are located on the ________ .

main shaft

When discussing shift linkages,Technician A says that occasionally the internal shift linkage of some manual transaxles may need to be adjusted.Technician B says that worn external shift linkage may cause excessive clutch pedal free play.Who is correct?

neither a nor b

When discussing shift mechanisms,Technician A says that the detent system prevents the engagement of more than one gear at a time.Technician B says that the interlock system places the shift rail and fork in an exact position.Who is correct?

neither a nor b

________ are moved by the gearshift and move the synchronizer sleeves to engage a gear.

shift forks

Which of the following is not something that should be done prior to installing a transmission a. Check for free rotation of the transmission in all gears before installing in a vehicle. b. Remove all lubricant from the input shaft splines. c. Make sure the block alignment pins (dowels) are in their appropriate bores and are in good shape. d. Make sure the pilot bearing in the crankshaft rotates smoothly and is lubricated.

B

Which of the following would not cause a harsh 3-4 upshift on a vehicle equipped with a six-speed manual transaxle? a. A worn synchronizer ring b. A binding synchronizer sleeve c. A misaligned shift rail d. Worn teeth on fourth gear of the counter gear

D

A bearing-type noise is coming from inside a manual transmission when the vehicle is stationary, the engine is running, and the clutch is engaged. The noise disappears when the clutch is disengaged.Technician A says that the input shaft bearing could be faulty.Technician B says that the rear main shaft support bearing could be faulty.Who is correct?

a only

Transmission fluid level and type are being discussed.Technician A says that the proper fluid level for a transmission is normally to the bottom of the filler hole.Technician B says that most modern manual transmissions require heavy gear lube for proper operation.Who is correct?

a only

When discussing overdrive gears,Technician A says that the typical ratio is 0.70 to 0.90:1.Technician B says that the typical ratio is 1.0:1.Who is correct?

a only

When discussion transmission repair,Technician A says that every part of a disassembled transmission should be carefully inspected, regardless of the problem.Technician B says that if the lubricant had traces of gold in it, it is likely that the gears will be severely worn.Who is correct?

a only

While discussing synchronizers,Technician A says that in automotive transmissions, the commonly used type of synchronizer is the block type.Technician B says that triple-cone synchronizers are not as effective because they are smaller than single-cone synchronizers.Who is correct?

a only

A vehicle equipped with a five-speed manual transmission sometimes jumps out of direct (fourth) gear.Technician A says that this may be caused by worn cluster gear teeth.Technician B says that a worn main shaft pilot bearing could cause this problem.Who is correct?

b only

When disassembling a transaxle, a severely worn second gear synchronizer blocker ring is found.Technician A says that this should have caused the transaxle to jump out of gear.Technician B says that this should have caused difficult shifting into second gear.Who is correct?

b only

When discussing current trends in manual transmissions,Technician A says that six- and seven-speed transmissions reduce fuel economy because of the weight of their extra parts.Technician B says that some manual transmissions are shifted by internal solenoids and do not require a shift lever.Who is correct?

b only

While assembling a transmission:Technician A says end play and preload cannot be adjusted on most transmissions and transaxles.Technician B says shims can be used to set the end play of the input shaft.Who is correct?

b only

While discussing shift forks,Technician A says most shift forks have two fingers that ride in the grooves on the outside of the speed gears.Technician B says each shift rail has three notches, which a spring-loaded ball or plunger rides in to give a detent feel to the shift lever and locates the proper position of the shift fork.Who is correct?

b only

When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear.Who is correct?

both a and b

When discussing the operation of a synchronizer,Technician A says that the synchronizer inserts force the blocking ring against the conical face of the gear, which slows the speed of the gear and allows for engagement.Technician B says that by matching the speed of the blocking ring and the gear, the synchronizer sleeve is able to engage with the gear dog teeth.Who is correct?

both a and b

When discussing the power-flow through a five-speed transmission when it is in first gear,Technician A says that power enters in on the input shaft, which rotates the countershaft that is engaged with first gear.Technician B says that the first gear synchronizer engages with the clutching teeth of first gear and locks the gear to the main shaft, allowing power to flow from the input gear through the countershaft and to first gear and the main shaft.Who is correct?

both a and b

When discussing transmission disassembly,Technician A says that the alignment of the parts of each synchronizer must be marked prior to disassembling the synchronizer assembly.Technician B says that most synchronizer hubs are splined to the shaft and are pressed on and off the shaft.Who is correct?

both a and b

When inspecting a transaxle's gears,Technician A says that a shiny wear pattern on the center of the gear teeth is normal.Technician B says that it is normal for a reverse idler gear to have small chips on its engagement side.Who is correct?

both a and b

When installing the shafts into the transmission case,Technician A says that the end play of the output shaft should be checked.Technician B says that the thrust washers and bearings should be lubricated prior to installing the shafts.Who is correct?

both a and b

While calculating the first gear ratio of a five-speed transmission,Technician A says to first divide the number of teeth on the front of the counter gear by the number of teeth on the clutch gear.Technician B says to next divide the number of teeth on the first-speed gear by the number of teeth on the matching counter gear and then multiply the answer from the first set by the second.Who is correct?

both a and b

While discussing power-flow through the forward gears of a typical transaxle,Technician A says the main speed gears freewheel around the output shaft unless they are locked to the shaft by the synchronizers.Technician B says the main speed gears are in constant mesh with their mating gears on the input shaft and rotate whenever the input shaft rotates. who is correct?

both a and b

While discussing reverse gear,Technician A says if the transmission has a synchronized reverse gear, the reverse synchronizer sleeve moves to engage with reverse gear. Power comes in through the input shaft, into the counter gear, through the reverse idler gear, and into the reverse gear on the main shaft. The reverse gear rotates the synchronizer sleeve, which rotates the hub and main shaft in a reverse direction.Technician B says if reverse is a nonsynchronized gear, a reverse-gear shift relay lever slides the reverse idler gear into contact with the countershaft reverse gear and the reverse gear on the output shaft. The reverse idler gear causes the reverse output shaft gear to rotate counterclockwise.Who is correct?

both a and b

A synchromesh transmission is a __________ , _________ transmission equipped with synchronizers.

constant mesh / collar shifted

If the speed gears are not engaged by a synchronizer, they ______ on the main shaft.

freewheel

All synchronizers use _______ to synchronize the speed of the gear and shaft before the connection is made.

friction

Smooth and quiet shifting can only be possible when the ________ and the ? are rotating at the same speed.

gears / ?

A transmission is a system of ________ that transfers the _______ to the _________ of the car.

gears / power / drive wheels

Block synchronizers consist of a ____ , ____ , _____ , and _____ .

hub / inserts / blocker ring / sleeve

When inspecting the gears of a transmission, a shiny wear pattern is found on the center of each gear.Technician A says that this was caused by worn shaft bearings.Technician B says that this was caused by worn synchronizers.Who is correct?

neither a nor b

When inspecting the synchronizers of a transaxle,Technician A says that if the dog teeth of the synchronizer are slightly rounded, the synchronizer assembly must be replaced.Technician B says that the sliding movement of the synchronizer sleeve on the output shaft should be checked.Who is correct?

neither a nor b

A manual transaxle is a single unit composed of a __________ , ________ , and _________ .

transmission / drive axles / differential


संबंधित स्टडी सेट्स

COM292 Organizational Com. Exam 1

View Set

Physics II: Motion, Force, Energy and Equilibrium

View Set

Mang 4468-Ch5 Job-based Structures & Job Evaluations

View Set

Module 5: Principles of Delegation and Prioritization of Care

View Set

Accounting 2101 - 7 through 9 Exam Study Set

View Set

Chapter 6 - A Revolution, Indeed

View Set