CME

Which of the following are required steps to create a phone with a functioning line in CME?

- Create a phone (ephone). - Create an extension (ephone-dn). - Associate the extension with the phone.

What does the command web admin system name username password password do?

- Defines the system administrator user for CME

Which three methods can remotely force a phone to reset in CME? (Choose three.)

- Issue a shutdown, no shutdown command on a switch port that provides PoE to a Cisco phone. - Issue the reset command under the ephone configuration of the phone. - Issue the reset H.H.H (mac-address) command telephony-service configuration.

which three methods can an engineer use to create users in CUC? (list three).

- Local - CUCM - LDAP

CME provides three user access levels. What are they? (Choose three.)

- System administrator - End user - Customer administrator

When you configure a shared extension in CCP, which two characteristics should be the same on both phones, so that the phones can successfully use a shared extension? (list two.)

- ephone-dn - number

Which of the following commands are required to enable CCP to configure the CME router? (pick 3)

- ip http server - username parkercx privilege 15 password abc123 - line vty 0 15

Which three models of configuration does CME support? (list three.)

- keyswitch - PBX - hybrid

Which three items are required to provision core telephony service on the CME router? (List three.)

1. IP source address 2. max-dn 3. max-ephone

Which of the following dial peer commands will match dial strings 1777 and 3777 (list 3)

1. R1(config) destination-pattern [13]777 2. R1(config) destination-pattern .777 3. R1(config) destination-pattern [1-3]777

A Cisco ip phone can be RESTARTS by what two ways

1. by issuing the RESTART command in ephone configuration mode on a CME router. 2. In the CUCM GUI, you can restart the phone by clicking DEVICE > PHONE > RESTART

A Cisco ip phone can be RESET by what two ways?

1. by issuing the reset command in ephone configuration mode on a CME router. 2. by pressing the **#** key sequence at the SETTING menu of an ip phone Note: also known as a hard reset, like unplugging the phone.

An SCCP IP phone places a call to a SIP phone that is registered to the same CME. During the active call, call waiting indicates a second call is incoming to the handset, but the user decides to ignore it. In this scenario, what is the combined total number of signaling conversations and media flows that used the SCCP phone as an endpoint?

3

what is the max number of digits that an ephone PIN can have to allow after-hour exempts calling privileges

8

You have the following configuration entered on your voice router: R1# dial-peer voice 99 pots R1# destination-pattern 115 R1# port 1/0/0 A user dials the number 1159. What digits does the router send out the port 1/0/0?

9

You issue the following commands on a CME router: R1(config) dial-peer voice 1 pots R1(config) destination-pattern 9911 R1(config) prefix 9 R1(config) port 1/0/0 Which of the following digits will be forwarded to the PSTN when a caller dials 9911? (select two)

9

What are some of the differences between the SIP configuration and SCCP configuration built for a 7970 ip phone in CME.

A voice register dn is assigned to a SIP voice register pool.

Which three tools are used to create phone user accounts in CME? (Choose three.)

A. Cisco Configuration Professional C. CLI D. GUI

Which three methods can remotely force a Cisco Unified Communications Manager Express phone to reset?

A. Issue a shutdown, no shutdown command on a switch port that provides PoE to a Cisco phone. C. Issue the reset command under the ephone configuration of the phone. E. Issue the reset H.H.H (mac-address) command telephony-service configuration.

Which component is needed for a voice call to be processed between the enterprise Cisco Unified Communications system and a cell phone via the PSTN?

Cisco Integrated Service Router with digital signal processor resources

Which CME GUI menu option is used to navigate to the screen used to add or change a user name or password using the CME CUI interface.

Configure > Phones

Which path would you use to implement end users in CME using CCP?

Configure > Unified Communications > Users, Phones and Extensions > Phones and Users

In CME, how would you create a directory entry and an internal caller ID name that is visible on the IP phones registered to the system?

Create an extension using CCP

Which of the following commands is used to match both inbound and outbound dial peers?

Destination-pattern

An administrator wants to verify that a new PRI is properly connected to the PSTN. Which Layer 2 status should be seen?

MULTIPLE_FRAME_ESTABLISHED

Wildcard [-] or [ ,]

Matches a range of digits. For example, [1-3]22 matches 122, 222, and 322. range of digits. A nonconsecutive range is indicated with a comma (,); for example, [5,8].

Wildcard (.)

Matches any dialed digit from 0-9 or the * key on the telephone keypad. For example, 20.. matches any number from 2000 through 2099.

wildcard T

Matches any number of dialed digits (from 0-32 digits).

Wildcard (+)

Matches one or more instances of the preceding digit. For example, 5+23 matches 5523, 55523, 555523, and so on. This trend continues up to 32 digits, which is the maximum length of a dialable number.

Two departments have their own call-park slot to park calls. Which feature on Cisco Unified CME allows one department to answer a call for another department?

Pickup-group

Customer requirements dictate that local calls from area code 408 display the ANI as a 7-digit number. Wh procedure allows th leading digits to be stripped as soon as they arrive at the H.323 voice gateway?

Set up a voice translation rule, apply the translation rule to a translation profile, apply the translation profile to the dial peer in the inbound direction

On the PSTN gateway, a network engineer runs Router# sh isdn status and finds the layer 2 state of each interface to be "TEI_ASSIGNED". What is the status of PSTN connectivity from this gateway?

The T1 interfaces are down

Wildcard X

The X wildcard matches any single digit in the range 0 through 9. Ex: The route pattern 9XXX routes or blocks all numbers in the range 9000 through 9999.

You issue the following commands on a Cisco voice router: voice translation-rule 1 rule 1 /^615/ // voice translation-profile VCE translate called 1 dial-peer voice 101 pots translation-profile incoming VCE direct-inward-dial port 1/0:21 Which of the following will occur when you issue the TEST VOICE TRANSLATION-RULE 1 6155550121 command from privilege EXEC mode?

The digits 615 will be stripped from the beginning of the string.

What is the final method used by a router to match an inbound dial peer for incoming calls?

Using dial peer 0

Which of the following key features supported by CUCM does CME not support?

VMware deployment on Unified Computing System platform

You click Administrator's Login Account in the CME GUI's Configure > System Parameters menu. Which of the following are you most likely configuring? (Select the best answer.)

a customer administrator

Which of the following destination patterns could you use to match any dialed number up to 32 digits in length? (Choose two.)

a. .+ c. T

You click Administrator Login Account in the CME GUI's Config > System Parameters menu. Which of the following are you most likely configuring?

customer Admin

What command can you enter to watch CME process calls as digits are dialed?

debug voip dialpeer

An administrator wants to add and configure an ephone-dn via the CME web GUI. Which feat must be defined under telephony service configuration?

dn-webedit

How to add a second line to a ephone-dn?

ephone-dn 1 dual-line

Which command allows the telephony service of a CME router to be associated to loopback address 192.168.143.44

ip source-address 192.168.143.44

What command can you use to verify QoS operations and packet statistics on a specific interface of your CME router?

show policy-map interface

if a dial peer is a VoIP dial peer what will the router do?

the router will fwd the call to the IP address indicated by the corresponding session target ipv4.

if a dial peer is a POTS dial peer what will the router do?

the router will fwd the call to the port indicated by the corresponding port.

Which of the following digit manipulation commands will work under a VoIP dial peer?

translation-profile

what does auto-reg-ephone do

users report that no phone numbers are listed in the corp dir, but the employee names are listed. Which option must be verified in CUCM Adiminstration to display the directory numbers? The telephone number field has been filled in appropriately what does auto-reg-ephone do? automatically create an ephone. when the ip phone registers, the router will associate the MAC of the ip phone w/ the first unassigned ephone on the router.