dhcp

A client device on an Ethernet segment needs an IP address in order to communicate on the network. A DHCP server with IP address 192.168.1.1 has been configured and enabled on the network. How will a client device obtain a usable IP address for this network?

Send a DHCPDISCOVER message to physical address FF-FF-FF-FF-FF-FF.

What is one indication that a Windows computer did not receive an IPv4 address from a DHCP server?

The computer receives an IP address that starts with 169.254.

The address pool of a DHCP server is configured with 192.168.234.0/27. The network administrator reserves 22 IP addresses for IP phones. How many IP addresses are left in the pool to be assigned to other hosts?

8

Refer to the exhibit. What should be done to allow PC-A to receive an IPv6 address from the DHCPv6 server?

Add the ipv6 dhcp relay command to interface Fa0/0.

A network administrator configures a router to send RA messages with M flag as 0 and O flag as 1. Which statement describes the effect of this configuration when a PC tries to configure its IPv6 address?

It should use the information that is contained in the RA message and contact a DHCPv6 server for additional information.

Which protocol automates assignment of IP addresses on a network, and which port number does it use?

DHCP 67

A host PC is attempting to lease an address through DHCP. What message is sent by the server to let the client know it is able to use the provided IP information?

DHCPACK

Step 4

DHCPv6 REPLY

Step 3

DHCPv6 REQUEST

Step 1

DHCPv6 SOLICIT

The address pool of a DHCP server is configured with 10.19.44.0/24. The network administrator reserves 6 IP addresses for servers. How many IP addresses are left in the pool to be assigned to other hosts?

248

Refer to the exhibit. PC1 is configured to obtain a dynamic IP address from the DHCP server. PC1 has been shut down for two weeks. When PC1 boots and tries to request an available IP address, which destination IP address will PC1 place in the IP header?

255.255.255.255

The address pool of a DHCP server is configured with 192.168.184.0/26. The network administrator reserves 18 IP addresses for access points. How many IP addresses are left in the pool to be assigned to other hosts?

44

a message that is used to suggest a lease to a client

DHCPOFFER

A message that is used to identify the explicit server and lease offer to accept

DHCPREQUEST

Which command will allow a network administrator to check the IP address that is assigned to a particular MAC address?

Router# show ip dhcp binding

DHCPOFFER

a DHCP server responding to the initial request by a client

Step 2

DHCPv6 ADVERTISE

The address pool of a DHCP server is configured with 172.18.93.0/25. The network administrator reserves 10 IP addresses for web servers. How many IP addresses are left in the pool to be assigned to other hosts?

116

a message that is used to acknowledge that the lease is successful

DHCPACK

A message that is used to locate any available DHCP server on a network

DHCPDISCOVER

Which message does an IPv4 host use to reply when it receives a DHCPOFFER message from a DHCP server?

DHCPREQUEST

A company uses DHCP servers to dynamically assign IPv4 addresses to employee workstations. The address lease duration is set as 5 days. An employee returns to the office after an absence of one week. When the employee boots the workstation, it sends a message to obtain an IP address. Which Layer 2 and Layer 3 destination addresses will the message contain?

FF-FF-FF-FF-FF-FF and 255.255.255.255

A small coffee shop is offering free Wi-Fi to customers. The network includes a wireless router and a DSL modem that is connected to the local phone company. What method is typically used to configure the connection to the phone company?

Set the WAN connection in the wireless router as a DHCP client.

After a host has generated an IPv6 address by using the DHCPv6 or SLAAC process, how does the host verify that the address is unique and therefore usable?

The host sends an ICMPv6 neighbor solicitation message to the DHCP or SLAAC-learned address and if no neighbor advertisement is returned, the address is considered unique.

Refer to the exhibit. PC-A is unable to receive an IPv6 address from the stateful DHCPv6 server. What is the problem

The ipv6 dhcp relay command should be applied to interface Gig0/0.

Refer to the exhibit. A network administrator is configuring a router for DHCPv6 operation. Which conclusion can be drawn based on the commands?

The router is configured for stateless DHCPv6 operation.

Refer to the exhibit. A network administrator is configuring a router as a DHCPv6 server. The administrator issues a show ipv6 dhcp poolcommand to verify the configuration. Which statement explains the reason that the number of active clients is 0?

The state is not maintained by the DHCPv6 server under stateless DHCPv6 operation.

Which statement is true about DHCP operation?​

When a device that is configured to use DHCP boots, the client broadcasts a DHCPDISCOVER message to identify any available DHCP servers on the network.​

What is a result when the DHCP servers are not operational in a network?

Workstations are assigned with IP addresses in the 169.254.0.0/16 network.

Which kind of message is sent by a DHCP client when its IP address lease has expired?​

a DHCPREQUEST unicast message​

DHCPDISCOVER

a client initiating a message to find a DHCP server

Which DHCPv4 message will a client send to accept an IPv4 address that is offered by a DHCP server?

broadcast DHCPREQUEST

What is the reason that an ISP commonly assigns a DHCP address to a wireless router in a SOHO environment?

easy IP address management

Which command, when issued in the interface configuration mode of a router, enables the interface to acquire an IPv4 address automatically from an ISP, when that link to the ISP is enabled?

ip address dhcp

Which set of commands will configure a router as a DHCP server that will assign IPv4 addresses to the 192.168.100.0/23 LAN while reserving the first 10 and the last addresses for static assignment?

ip dhcp excluded-address 192.168.100.1 192.168.100.10 ip dhcp excluded-address 192.168.101.254 ip dhcp pool LAN-POOL-100 network 192.168.100.0 255.255.254.0 default-router 192.168.100.1

Refer to the exhibit. Based on the output that is shown, what kind of IPv6 addressing is being configured?

stateless DHCPv6

What information can be verified through the show ip dhcp binding command?

the IPv4 addresses that are assigned to hosts by the DHCP server

DHCPREQUEST

the client accepting the IP address providing by the DHCP server

A company uses the SLAAC method to configure IPv6 addresses for the employee workstations. Which address will a client use as its default gateway?

the link-local address of the router interface that is attached to the network

What is the result of a network technician issuing the command ip dhcp excluded-address 10.0.15.1 10.0.15.15 on a Cisco router?

The Cisco router will exclude 15 IP addresses from being leased to DHCP clients.

What is an advantage of configuring a Cisco router as a relay agent?

It can provide relay services for multiple UDP services.

Refer to the exhibit. A network administrator is implementing the stateless DHCPv6 operation for the company. Clients are configuring IPv6 addresses as expected. However, the clients are not getting the DNS server address and the domain name information configured in the DHCP pool. What could be the cause of the problem?

The router is configured for SLAAC operation.

DHCPACK

the DHCP server confirming that the address lease has been accepted

A company uses DHCP to manage IP address deployment for employee workstations. The IT department deploys multiple DHCP servers in the data center and uses DHCP relay agents to facilitate the DHCP requests from workstations. Which two UDP ports are used to forward DHCP traffic?

67 68

A company uses the method SLAAC to configure IPv6 addresses for the workstations of the employees. A network administrator configured the IPv6 address on the LAN interface of the router. The interface status is UP. However, the workstations on the LAN segment did not obtain the correct prefix and prefix length. What else should be configured on the router that is attached to the LAN segment for the workstations to obtain the information?

R1(config)# ipv6 unicast-routing