Drilling Test

अब Quizwiz के साथ अपने होमवर्क और परीक्षाओं को एस करें!

The reamer should be driven about _______ the RPM of your drilling speed

1/2

Included angle of the lips on a general twist drill is

118 degrees

Countersinks are commonly found with included angles of

60,82,90 and 100 degrees.

What is a blind hole

A hole that is not drilled all the way through the work piece.

What is a pilot hole

A smaller hole drilled before the larger hole is then drilled

Feed

Advancement of the cutting tool into a workpiece

Name three functions of the flutes on a twist drill.

Create the cutting lips. Provide a pathway for chips to flow out of the hole during drilling operations and for cutting fluid to flow into the hole to help cool and lubricate the cutting lips.

What is drilling?

Drilling i s the process of using a cylindrical rotating cutting tool that is sharpened on its end to create a hole.

Twist drill bits have spiral grooves in their sides called...

Flutes

Materials used to make hole making cutting tools:

HSS, Tungsten Carbide

Explain the purpose of a counterbore.

It allows a screw head or nut to be positioned flush with or below the surface of the workpiece surface.

Twist Drill bits are sized according to diameter by four methods...

Letter, Wire gage or Number drill, Fractional drill, Metric Drill

What should be done as a drill nears the "breakthrough" point during drilling?

Lighten up on the pressure to prevent grabbing.

What is the largest diameter of a thread?

Major diameter

Parts to a twist drill

Shank,Body, Drill Point

What is general-purpose hand drillinh usually done with?

Twist Drills

What are two reasons why a hole may need to be countersunk?

When a chamfer is needed or a flathead screw must be installed.

What factors might determine when a hole must be finished by reaming?

When a smooth finish and precise size are needed.

A thread is

a spiral groove made on a round external or internal diameter

Countersinking with an 82 degree countersink bit will accommodate...

a standard flathead screw.

Countersinking is also peformed to create a...

chamfer at the opening of a hole.

Upright drill press consists of a

column mounted at 90 degrees to a base.

An external thread is cut with a

die

A hole slightly smaller than the desired size must first be...

drilled

Counterboring...

increases the diamter of a hole to a certain depth in order to allow a screwhead or nut to be positioned flush with or below the workpiece surface.

Countersinking

is the process of cutting a tapered opening holr so that a flathead screw can be installed flush with the workpiece surface.

Reaming

is the process of finsihing a hole to precise size with a smooth finished surface.

Spotfacing

is the process of machining a flat spot on a rough surface surrounding a hole opening so that bolts, nuts, and washers will be properly seated when tightened.

(Reaming) For a hole up to 1/4"...

should be produced undersize by 0.010"

(Reaming) for a hole between 1/4" and 1/2"...

should be produced undersize by 0.015"

(Reaming) for a hole between 1/2" and 1-1/2"...

should be produced undersize by 0.025

Two types of starter drill bits are the

spot drill and center drill

List two types of drill shanks

straight and tapered.

__________ shank drills are used with a chuck.

straight.

An internal thread is cut with a

tap

__________ shank drills fit directly into the drill press spindle

tapered.

V-Blocks are used

to securely hold round workpieces while performing drilling or reaming

Before beginning to drill a hole, its recommended to center punch the part so the drill does not...

walk


संबंधित स्टडी सेट्स

NCLEX Practice Questions to Remember

View Set

OB Chap 21 Nursing Management of Labor and Birth at Risk

View Set

Chapter 9: Building a New Venture Team

View Set

AP Environmental Science Unit 7 Exam Review

View Set

OB Chapter 31; The Infant and Family

View Set