Intro-Indust.internetofthings
Convert 9/16 inch to decimal inches.
0.5625
Before running the robot, the operator should perform prestart checks, power up and enable the drives, and __________.
Home the robot
Many of the safety devices for the robot are designed to protect the human interaction with the robot. Which is the only safety device designed for the operator to protect the robot?
emergency stop
what is this view called
isometric
CNC (Computer Numerical Control) refers specifically to a computer that controls what aspect of the machine?
motion
A normal die, such as what is used in a board game, would require what type of drawing?
multi-view
Which micrometer scale is printed vertically around the left edge of the thimble?
thimble
A universal standard makes it possible for manufactured parts __________.
to be used in many different countries
Advanced manufacturing increases competitiveness through the use of refined methods and technology. Is this statement TRUE or FALSE?
true
The control devices used in pneumatics are called __________.
valves
What should be done every time before taking a measurement with dial calipers?
Check the calibration
Powering up a servo robot includes more than just turning on the power. A safety precheck is completed before any power up. The precheck includes __________.
Checking dress code, clean and clear workcell
Robot grippers have two types of motion: parallel and curvilinear. Curvilinear has __________.
Circular motion from a single pivot point
What is the basic measuring device on a dial caliper?
rule
To begin running the program, the controller software needs to be in __________ mode.
run
what is this type of robot
scara robot
What is a view projected from a primary view called?
secondary auxiliary view
5s's
see pic
wastes of lean manufacturing
see pic
The robot program uses __________ commands to perform each operation.
separate
what is this type of robot
spherical/polar robot
The 3-position, 5-way DCV is held in the middle-position by the __________.
springs
Servo Robots use Pmove or point move to program the robots movements. The points are most often recorded using a __________.
teach pendant
Teaching points requires an open program and __________.
teach pendant
Which component of IIoT allows networked devices to exchange information?
Machine-to-machine communication
Which of the following statements does not accurately describe a part of the process of measuring the resistance of a component that is connected in a circuit?
Make sure the power supply is on.
Jogging a servo robot means __________.
Manually moving the robot arm to a new position without a program
__________ is the process of converting raw materials into finished goods.
Manufacturing
what is the first step in lock out tag out
1. find the correct procedure 2. notify anyone affected. locate all listed energy sources 4. shut down machine 5. lockout and tagout 6. release any stored energy 7. operate controls to test disconnects 8. return to off position
How is a half scale drawing written?
1:2
Tubular inside micrometers are used to measure inner dimensions that are what size?
25 mm or larger
To convert inches to millimeters, multiple the inches by __________.
25.4
The conversion of 3-3/8 inches to decimal inches is __________.
3.375 inches
Which one of the following logic elements describes a circuit with two normally open input switches in series?
AND
The __________ approves standards for pressure vessels in the United States.
ASME
__________ manufacturing creates a product by adding material layer-on-layer. (3D Printing)
Additive
After correcting an issue, what screen should be checked to ensure there are no more problems before restarting the machine?
Alarm
When a machine stops due to an problem, what would the machine's HMI typically display?
An error message.
How are angled surfaces dimensioned?surface linear measurement number and degree Correct! Both B and C
Both B and C
Which robots use an X-Y-Z coordinate system?
Cartesian
Which software has greatly shortened the development cycle for new and improved products?
Computer Aided Design (CAD)
Turning outputs on or off through relay contacts is called __________.
Control Logic
A regulator is used in pneumatics to __________.
Control outlet pressure in a circuit
An ammeter is used to measure __________.
Current
A(n) __________ communication system uses IoT to monitor smart sensors and output devices to determine when they are about to fail.
Cyber-Physical
What pneumatic component provides straight line motion?
Cylinder
What device provides the means by which electrical circuits control pneumatic or hydraulic systems?
DCV
These robots are used in the food, pharmaceutical, and electronics industries.
Delta
What method is used to determine the initial state of each output in the ladder diagram?
Determine the initial status of the inputs
Dimensional measurement determines physical dimensions such as __________.
Diameter, width, and height
DCV stands for __________.
Directional Control Valve
The most common end effector is powered by __________.
Electricity or pneumatics
Smaller dirt particles are removed from the air by the filter's __________.
Element
Once points are established the programmer can use the PC software to __________.
Enter codes of instruction
Using datums helps eliminate __________.
Errors in measurement
What standard introduced in the early 1980s established a method to physically connect machines from different manufacturers enabling them to communicate to one another?
Ethernet
How often should a micrometer's calibration be checked?
Every few months
Dimension lines are usually placed between two __________ lines.
Extension
Automation increases quality, but it also creates a larger risk for human error. Is this statement TRUE or FALSE?
False
Which component on an outside micrometer greatly reduces measurement time?
Fast drive
The three Fs of product design are __________.
Form, Fit, Function
Which of the following is a type of circuit protection device?
Fuse
what uses pictograms to show danger
GHS
A pneumatic system uses a(n) __________ to provide power.
Gas
While this point is critical for circuit safety, it also makes a convenient common reference point for point voltage measurements.
Ground
what differentiates industry 4.0 from 3.0
In Industry 3.0, we automate processes using logic processors and information technology. These processes often operate largely without human interference, but there is still a human aspect behind it. Where Industry 4.0 comes in is with the availability and use of vast quantities of data on the production floor
The purpose of automation has shifted from increasing productivity and reducing costs to __________.
Increasing quality and flexibility
Air supplied to a pneumatic system is supplied through the __________ line.
Intake
The label command gives a portion of the program a name which allows the program to branch to the newly named section of the program. Branch means __________.
Jumping to a reference label within the program
Rules are designed to protect the operator and the robot equipment. The operator must follow and complete the safety system and training, locate the emergency stops, and __________.
Monitor the controls and nearby personnel
Which of the following is an IIoT application?
Monitoring in-plant processes
An electromechanical relay includes which of these components?
NO contacts, NC contacts, and a solenoid coil
Which of the following is an element of control logic?
NOR, AND, NOT
Where there is no continuity found when testing with a DMM, the screen may display this.
OL
Resistance is measured in units of __________.
Ohms
Which of the following is NOT an important step of regular maintenance?
Operate at high temperatures
Which of the following is a formula for calculating power?
P = I × E
The automation of many different manufacturing processes is done through the use of a small computer called a __________.
PLC - Programmable Logic Controller
The title block contains the __________.
Part name, drawing number and information to identify the part
What assembly moves inside the barrel-shaped body of a cylinder?
Piston/Rod
The Home position is the __________.
Prescribed position for the robot where all sensors are activated
Increasing force in a Hydraulic system causes __________.
Pressure to increase
What type of drawing defines how the product is going to be manufactured?
Process drawing
A(n) __________ provides power to a hydraulic system by pumping oil from a reservoir into the supply lines..
Pump
What is the total caliper measurement equal to?
Scale reading + dial reading
A(n) __________ diagram uses symbols to represent electrical devices and how they are connected.
Schematic
An example of memory logic by a control relay is __________.
Seal-in Circuit
A(n) __________ switch uses a rotary motion to open and close contacts.
Selector
What are the axes of a robot named?
Shoulder, elbow, waist
Which drawing method is a form of free-hand drawing?
Sketching
Robots are classified into four groups: type of motion, servo or non-servo, number of axes, and __________.
Stationary or mobile
Which manufacturing logistics application of IIoT includes the resources to move a product or service from the supplier to the customer?
Supply chain management
One of the most important assets of advanced manufacturing is the people who work together to develop the products. Is this statement TRUE or FALSE?
TRUE
This type of fitting connects two branch circuits to a single supply line.
Tee
In a feature control frame there is a symbol, a number, and a letter. What does the number represent?
The total amount of tolerance for the geometric feature
Industry uses quick connect fittings when __________.
There is a frequent need to connect and disconnect a pneumatic conductor
CAD and CAM systems allow for easy customization and quick design changes. Is this statement TRUE or FALSE?
True
One of the advantages of incorporating computers into the manufacturing process is that manufacturers can quickly adjust production schedules. Is this statement TRUE or FALSE?
True
The pressure created by any force is calculated by multiplying the total force by the total area. Is this statement TRUE or FALSE?
True
OR logic is formed by __________.
Two normally open input switches in parallel
Two systems of dimensional measurement used in manufacturing are the SI Metric System and the __________.
US customary system
Robot programs can be transferred by physical cables connected between the computer and the robot controller. Another way to transfer programs is to __________.
Use a USB thumb drives
The unit of measurement for voltage is the __________.
Volt
3d printing uses what type of manufacturing
additive
what is this type of robot
cartesian robot
Which schematic symbol depicts energy conversion devices, such as an air motor, in a pneumatic schematic?
circle
Which of the components listed are on the digital caliper but not on the dial caliper?
computer port
deals with medical also moves very fast
delta robot
Filters should be used on all pneumatic systems because atmospheric air contains __________.
dirt
Force can be measured in __________.
pounds
Robot grippers are classified according to __________ and number of fingers.
power
Which IIoT application monitors equipment during normal operation to prevent failures to the equipment?
predictive maintenance