Module 8 & 9 knowledge checks

What process is used in ICMPV6 for st to verify that an IPV6 address is unique before configuring it on an interface?

DAD

A company implements the stateless DHCPV6 method for configuring IPV6 addresses on employee workstations. After a workstation receives messages from multiple DHCPV6 servers to indicate their availability for DHCPV6 service, which message does it send to a server for configuration information?

DHCPV6 INFORMATION-REQUEST

True or False? If a router with a higher HSRP priority joins the network, it will take over the active router roll from an existing active router which has a lower priority.

False

A network engineer is configuring a LAN with a redundant first hop to make better use of the available network resources. Which protocol should the engineer implement?

GLBP

A network administrator is entering the command ipv6 unicast-routing to start configuring DHCPV6 operation on a router. Which statement describes the function of this command?

It is required for sending ICMPV6 RA messages.

A client is using SLAAC to obtain an Irvo address for its interface. After an address has been generated and applied to the interface, what must the client do before it can begin to use this IPV6 address?

It must send an ICMPV6 Neighbor Solicitation message to ensure that the address is not already in use on the network.

How does an IPV6 client ensure that it has a unique address after it configures its IPV6 address using the SLAAC allocation method?

It sends an ICMPV6 Neighbor Solicitation message with the IPV6 address as the target IPV6 address.

A network administrator is analyzing first-hop router redundancy protocals. What is a characteristic of VRRPv3?

It supports IPV6 and IPV4 addressing.

What M flag setting indicates that stateful DHCPV6 is used?

M=1

In which alternative to DHCPV6 doesouter dynamically provide IPV6 configuration information to hosts?

SLAAC

Which method best describes stateless DHCP?

SLAAC with stateless DHCPV6 Server

What DHCPv6 message does a host send to look for a DHCPV6 server?

SOLICIT

What type of device routes traffic destined to network source network segment for which the sending node may not have explicit segments beyond the routing information?

default gateway

Which command should be configured on a router interface to set the router as a stateful DHCPV6 client?

ipv6 address dhcp

Which is a characteristic of the HSRP learn state?

the router has not determined the virtual IP address

What device presents the illusion of a single router to hosts on a LAN segment but actually represents a set of routers working together?

virtual router

What is the purpose of HSRP?

It provides a continuous network connection when a router fails.

What DHCPV6 message does a host send to the DHCPV6 server if it is using stateful DHCPV6?

REQUEST

Which ICMPV6 message is sent by a host in an attempt to locate an online IPv6enabled router to obtain IPV6 addressing information?

Router Solicitation (RS)

After booting, a client receives an ICM RA message with the M flag set to 0 and the O flag set to 1, What does this indicate?

The client should automatically configure an IPV6 address and then contact a DHCPV6 server for more information.

Which command is not configured in stateless DHCPV6?

address prefix ipv6-address/prefix

What device that is part of a virtual router group assigned to the role of default gateway?

forwarding router

An IPV6-enabled router is to acquire its IPV6 GUA from another IPV6 router using SLAAC. Which interface configuration command should be configured on the client router?

ipv6 address autoconfig

An IPV6-enabled router is to acquire its IPV6 GUA from a DHCPV6 server. Which interface configuration command should be configured on client router?

ipv6 address dhcp

Which command is configured on the client LAN interface of the DHCPV6 relay agent?

ipv6 dhcp relay destination

A router is to provide DHCPV6 server services. Which command should be configured on the client facing interface?

ipv6 dhcp server POOL-NAME

Which command must be configured on a router to enable it to join the IPV6 all- routers multicast address ff02:2?

ipv6 unicast-routing

Which address type is automatically created by default on a host interface when no RAs are received?

link-local address

Which method would an IPv6-enabled address of the default gateway? host using SLAAC employ to learn the

router advertisements that are received from the link router

Which DHCPV6 verification command would display the link-local and GUA assigned address for each active client?

show ipv6 dhcp binding

In FHRP terminology, what represents a set of routers that present the illusion of a single router to hosts?

virtual router

What UDP port do DHCPV6 clients use to send DHCPV6 messages?

547

What flag settings combination is used for stateless DHCP?

A=1, M-0, O=1

What are the flag settings when a host should use the SLAAC only option?

A=1, M=0, O=0

What method is used by a host to verify an IPV6 address is unique on the local network before assigning that address to an interface?

DAD

Which destination IP address is used when an IPV6 host sends a DHCPV6 SOLICIT message to locate a DHCPV6 server?

FF02::1:2

What is a potential disadvantage when implementing HSRP as compared to GLBP?

HSRP does not provide load balancing with multipie active routers.

During which HSRP state does an interface begin sending periodic hello messages?

speak

What device is part of a virtual router group assigned the role of alternate default gateway?

standby router

What message informs IPV6 enabled i faces to use stateful DHCPv6 for obtaining an IPv6 address?

the ICMPV6 Router Advertisement

Which three DHCPV6 roles can a router perform? (Choose all that apply.)

1.) DHCPV6 client 2.) DHCPV6 relay agent 3.) DHCPV6 server

A network administrator is overseeing the implementation of first hop redundancy protocols. Which two protocols are Cisco proprietary? (Choose two)

1.) HSRP 2.) GLBP

Which FHRPS are Cisco-proprietary? (Choose two.)

1.) HSRP 2.) HSRP for IPV6

What two methods can be used to generate an interface ID by an IPV6 host that is using SLAAC? (Choose two.)

1.) random generation 2.) EUI-64

What is the default HSRP priority?

100

What are two characteristics of the SLAAC method for IPv6 address configuration? (Choose two.)

1.) IPV6 addressing is dynamically assigned to clients through the use of ICMPV6. 2.) The default gateway of an IPV6 client on a LAN will be the link-local address of the router interface to the LAN.

6. When first hop redundancy protocols are used, which two items will be shared by a set of routers that are presenting the illusion of being a single router? (Choose two.)

1.) MẠC address 2.) IP address

Which two ICMPV6 messages are used in the SLAAC process? (Choose two.)

1.) Router Solicitation (RS) 2.) Router Advertisements (RA)

A user needs to add redundancy to the routers in a company. What are the three options the user can use? (Choose three.)

1.) VRRP 2.) GLBP 3.) HSRP

Which two protocols provide gateway redundancy at Layer 3? (Choose two.)

1.) VRRP 2.) HSRP

Which nonproprietary protocol provides router redundancy for a group of routers which support IPV4 LANS?

VRRPV2