Network= (Troubleshooting)
Satellite
Which of the following WAN technologies is associated with high latency?
Incorrect VLAN assignment
A PC technician has installed a new network printer that was preconfigured with the correct static IP address, subnet mask, and default gateway. The printer was installed with a new cable and appears to have link activity, but the printer will not respond to any network communication attempts. Which of the following is MOST likely the cause of the problem?
The router interface is configured with the incorrect IP address. The default gateway is configured incorrectly.
A company has changed ISPs for their office and ordered a new 250 Mbps symmetrical Internet connection. As a result, they have been given a new IP range. The ISP has assigned the company 10.10.150.16 /28. The company gateway router has the following interface configuration facing the ISP: Interface A: IP address: 10.10.150.16 Subnet mask: 255.255.255.240 Default gateway: 10.10.150.32 Speed: 1000 Mbps Duplex: Auto State: No Shutdown None of the workstations at the company are able to access the Internet. Which of the following are the reasons? (Select TWO).
Update the DNS server with the proxy server information.
A network administrator recently installed a web proxy server at a customer's site. The following week, a system administrator replaced the DNS server overnight. The next day, customers began having issues accessing public websites. Which of the following will resolve the issue?
Missing default gateway
A network engineer is troubleshooting an issue with a computer that is unable to connect to the Internet. The network engineer analyzes the following output from a command line utility: Network DestinationNetmaskGatewayInterface 192.168.1.0 255.255.255.0192.168.1.254eth0 192.168.1.10255.255.255.255192.168.1.10eth0 127.0.0.1255.0.0.0On-Linlo 127.0.0.0255.0.0.0On-Linklo 255.255.255.255255.255.255.255102.168.1.10eth0 Which of the following is the reason for the computer issue, given the above output?
The gateway is mis-configured on the new router.
A network technician has been assigned to install an additional router on a wireless network. The router has a different SSID and frequency. All users on the new access point and the main network can ping each other and utilize the network printer, but all users on the new router cannot get to the Internet. Which of the following is the MOST likely cause of this issue?
show mac address-table
A network technician has detected a personal computer that has been physically connected to the corporate network. Which of the following commands would the network technician use to locate this unauthorized computer and determine the interface it is connected to?
Establish a plan to locate the rogue DHCP server.
A network technician has detected duplicate IP addresses on the network. After testing the behavior of rogue DHCP servers, the technician believes that the issue is related to an unauthorized home router. Which of the following should the technician do NEXT in the troubleshooting methodology?
Placement
A network technician has received a help desk ticket indicating that after the new wireless access point was installed, all of the media department's devices are experiencing sporadic wireless connectivity. All other departments are connecting just fine and the settings on the new access point were copied from the baseline. Which of the following is a reason why the media department is not connecting?
tracert
A network technician has received comments from several users that cannot reach a particular website. Which of the following commands would provide the BEST information about the path taken across the network to this website?
Configure the firewall to allow echo reply in and echo request out of the network
A network technician is performing a tracert command to troubleshoot a website-related issue. The following output is received for each hop in the tracert: 1 * * * Request timed out. 2 * * * Request timed out. 3 * * * Request timed out. The technician would like to see the results of the tracert command. Which of the following will allow the technician to perform tracert on external sites but not allow outsiders to discover information from inside the network?
Rogue AP
A network technician is performing a wireless survey in the office and discovers a device that was not installed by the networking team. This is an example of which of following threats?
The interface status will show line protocol down.
A network technician is troubleshooting a problem at a remote site. It has been determined that the connection from router A to router B is down. The technician at the remote site re-terminates the CAT5 cable that connects the two routers as a straight through cable. The cable is then tested and is plugged into the correct interface. Which of the following would be the result of this action?
Determine if anything has changed.
A network technician is using a network monitoring system and notices that every device on a particular segment has lost connectivity. Which of the following should the network technician do NEXT?
Is the user able to access any network resources?
A user calls the help desk and states that he was working on a spreadsheet and was unable to print it. However, his colleagues are able to print their documents to the same shared printer. Which of the following should be the FIRST question the help desk asks?
The user is connected to the wrong SSID
A user connects to a wireless network at the office and is able to access unfamiliar SMB shares and printers. Which of the following has happened to the user?
Toner probe
A technician has verified that a recent loss of network connectivity to multiple workstations is due to a bad CAT5 cable in the server room wall. Which of the following tools can be used to locate its physical location within the wall?
The wrong wavelength was demuxed from the multiplexer.
A technician is tasked with connecting a router to a DWDM. The technician connects the router to the multiplexer and confirms that there is a good signal level. However, the interface on the router will not come up. Which of the following is the MOST likely cause?
The WAP is using AES encryption The WAP is using the 5GHz channel
A technician is troubleshooting a client's connection to a wireless network. The client is asked to run a "getinfo" command to list information about the existing condition. myClient$ wificard --getinfo agrCtlRSSI:-72 : agrExtRSSI:0 : state:running op mode: station last TxRate:178 MaxRate:300 802.11 auth:open link auth:wpa2-psk BSSID:0F:33:AE:F1:02:0A SSID:CafeWireless Channel:149,1 Given this output, which of the following has the technician learned about the wireless network?(Select TWO).
Bad wiring
A technician is troubleshooting a wired device on the network. The technician notices that the link light on the NIC does not illuminate. After testing the device on a different RJ-45 port, the device connects successfully. Which of the following is causing this issue?
Electromagnetic interference
A technician recently ran a 20-meter section of CAT6 to relocate a control station to a more central area on the production floor. Since the relocation, the helpdesk has received complaints about intermittent operation. During the troubleshooting process, the technician noticed that collisions are only observed on the switch port during production. Given this information, which of the following is the cause of the problem?
Run the following command on the administrator's workstation: arp -s 192.168.1.200 01:4a:d1:fa:b1:0e
After connecting a workstation directly to a small business firewall, a network administrator is trying to manage it via HTTPS without losing its stored configuration. The only two pieces of information that the network administrator knows about the firewall are the management interface MAC address, which is 01:4a:d1:fa:b1:0e, and the administrator's password. Which of the following will allow the administrator to log onto the firewall via HTTPS if the management's IP address is unknown and the administrator's workstation IP address is 192.168.0.10/23?
Local hosts file
After repairing a computer infected with malware, a technician determines that the web browser fails to go to the proper address for some sites. Which of the following should be checked?
ipconfig
An administrator only has telnet access to a remote workstation. Which of the following utilities will identify if the workstation uses DHCP?
Bounce
Ann, a user, is experiencing an issue with her wireless device. While in the conference area, the wireless signal is steady and strong. However, at her desk the signal is consistently dropping, yet the device indicates a strong signal. Which of the following is the MOST likely cause of the issue?
Via HTTP using the default username and password
Two weeks after installation, a network technician is now unable to log onto any of the newly installed company switches. The technician suspects that a malicious user may have changed the switches' settings before they were installed in secure areas. Which of the following is the MOST likely way in which the malicious user gained access to the switches?
Split horizon
Which of the following helps prevent routing loops?
DHCP server
While troubleshooting a connectivity issue, a network technician determines the IP address of a number of workstations is 169.254.0.0/16 and the workstations cannot access the Internet. Which of the following should the technician check to resolve the problem?
Bend radius exceeded
While troubleshooting a network outage, a technician finds a 100-meter fiber cable with a small service loop and suspects it might be the cause of the outage. Which of the following is MOST likely the issue?
Since we know that the network was running perfectly before replacing AP2 we should start by looking at this new device that was used to replace the old one. Here we see that the other AP's have hard coded the speed and duplex settings to 100/full, while AP2 is set to auto/auto. Also, the other AP's have been configured to use 802.11G, while AP2 is using 802.11B. Finally the channel that AP2 is using overlaps with AP1 which can cause problems. Channels 1, 6, and 11 are spaced far enough apart that they don't overlap. On a non-MIMO setup (i.e. 802.11 a, b, or g) you should always try to use channel 1, 6, or 11. Since AP1 is using 1, and AP3 is using 11, AP2 should be using 6. References: Dulaney, Emmett and Mike Harwood, CompTIA Network+ Authorized Exam Cram, Fourth Edition, Pearson, Indianapolis, 2012, p 269. Lammle, Todd, CompTIA Network+ Deluxe Study Guide, Deluxe Edition, Wiley Publishing, Inc., Indianapolis, 2009, pp 676, 677. http://en.wikipedia.org/wiki/List_of_WLAN_channels#2.4.C2.A0GHz_.28802.11b.2Fg.2Fn.29
Wireless network users recently began experiencing speed and performance issues after access point 2 (AP2) was replaced due to faulty hardware. The original network was installed according to a consultant's specifications and has always worked without a problem. You, a network technician, have been tasked with evaluating the situation and resolving the issues to improve both performance and connectivity. Refer to the following diagram and perform any NECESSARY changes to the wireless and wired infrastructure by adjusting devices. Note: Adjust the LEAST number of devices needed to fix the issue, all blue icons in the image are clickable. When you feel the simulation is complete please select the Done button.