TOOLS IN CONSTRUCTION

अब Quizwiz के साथ अपने होमवर्क और परीक्षाओं को एस करें!

PLUMB BOB

A heavy weight that is suspended from a line It indicates vertical trueness

BACK SAW

A kind of saw with a rigid blade, more effective in cutting long straight lines.

SPIRAL RATCHET SCREWDRIVER

A screwdriver that relies on a pushing force rather than a twisting force

PLUMB LINE

A string with a weight used to provide a vertical reference line

PITIK

Chalk line

COLD CHISEL

Chisel used for metal work or sheet metal forming.

MARTILYO

Claw hammer

PUNSOL

Nail set

WOOD CHISEL

PAET

CHALK LINE

Pitik

HULOG

Plum bob

KABRA

Prybar

NAIL SET

Punsol

WOOD FLOAT

Rodelang kahoy

NAIL SET

Short, tapered bars of steel that serve as a companions to a hammer in order to prevent damage to the wood by stopping just short of driving the nail completely, then using this tool to finish the job This small, inexpensive accessory extends your reach with the hammer, letting you strike just the nail—not the wood trim

METRO

Steel Tape Measure

LONG TAPE

These measuring tapes are best for measuring long distances on-site that normal tapes cannot handle

NAIL SET

Though they vary in design, they are typically made from a hard round or square steel rod which tapers at one end to a flat or slightly hollowed tip The tip is placed against the head of the nail, while the other end is struck with a hammer

LEVEL BAR / SPIRIT LEVEL

Used for establishing horizontal and vertical levels.

LEVEL BAR / SPIRIT LEVEL

Used for establishing horizontal and vertical levels. Uses a bubble contained inside a cylinder of colored fluid.

STEEL TAPE MEASURE

Used for general measurement work

COLD CHISEL

Used for gouging, cutting, shaping, or smoothing metal

WOOD CHISEL

Used for gouging, cutting, shaping, or smoothing wood

PRYBAR

Used for prying open boards, demolition work and general removal of construction assemblies

LONG TAPE

Used for relatively long measurements such as lot lines or large room dimensions.

HACK SAW

Used to cut metal. Has a replaceable blade with fine teeth.

HAND SAW

Used to cut wood by hand

CHALK LINE

Used to draw long straight lines without having to use pencil or pen.

ROTARY HAMMER

Used to embed longer nails with larger diameter into hard surfaces

PLUMB BOB

Used to establish vertical line known as a plumb line.

NAIL SET

Used to push in the nail head into the lumber surface.

PLUMB BOB

Vertical plumbing to locate points

PAET

Wood chisel

RODELANG KAHOY

Wood float

WOOD FLOAT

Wood used for flattening or levelling small plaster areas.

NAIL SET

a hand tool used for driving the exposed head of a nail or pin below the surface of a piece of wood, such as when installing decorative moulding or face-fastening wood flooring

HACK SAW

a hand-powered, small-toothed saw used for cutting metal pipes, rods, brackets, etc. has a U-shaped frame and a handle at one end and small pins at each end of the frame that receive a blade

PLUMB BOB

a heavy weight that's suspended from a line that indicates vertical trueness

WOOD FLOAT

a kind of float that is particularly useful in those stressful instances in which concrete is setting up too quickly

PLUMB LINE

a line with a plumb attached to it, used for finding the depth of water or determining the vertical on an upright surface.

ROTARY HAMMER

a power tool that can perform heavy-duty tasks such as drilling and chiseling hard materials. It is similar to a hammer drill in that it also pounds the drill bit in and out while it is spinning

NAIL SET

a small metal tool that allows you to hammer the finish nail flush to, or slightly below, the surface of the wood while keeping the hammerhead a safe distance away

BACK SAW

a specialized handsaw for cutting tenons (joints or grooves) in wood. The blade is rectangular, 8 to 14 inches in length, with a hardwood or plastic handle and a metal-reinforced back edge (opposite the teeth) to keep the blade from bending while cutting

SURVEYOR'S TAPE

also called Long Tape

LONG TAPE

also called Surveyor's Tape

BACK SAW

any hand saw which has a stiffening rib on the edge opposite the cutting edge, enabling better control and more precise cutting than with other types of saws normally used in woodworking for precise work, such as cutting dovetails, mitres, or tenons in cabinetry and joinery.

LONG TAPE

specially designed to precisely measure longer distances between 100-300 feet.

STEEL FLOAT

type of float used for smooth finish concrete, spreading mortar for tiles, plastering, etc.

HACK SAW

type of handsaw that's used to cut metal

RIP SAW CROSSCUT SAW

types of hand saw:

STEEL FLOAT

used for smoothing the surface of concrete prior to it setting

NAIL SET

used for the final few blows onto the exposed heads of finish nails, sinking them beneath the surface without collateral damage to the surrounding wood

CLAW HAMMER

Martilyo

STEEL FLOAT

Metal used for smoothening plaster.

STEEL TAPE MEASURE

Metro

NAIL SET

Instead of just using a hammer alone, this tool also helps in driving a finish nail or casing nail into wood trim so that it is flush or slightly countersunk below the surface without damaging the wood

PRYBAR

Kabra

HAND SAW

Lagari

HACK SAW

Lagaring bakal

LEVEL BAR / SPIRIT LEVEL

Lebel / Nibel

LEBEL / NIBEL

Level bar / Spirit level

BALL PIN HAMMER

Hammer usually used for metal work/ sheet metal work.

LAGARI

Hand saw

PLUM BOB

Hulog

STEEL FLOAT

Ideal in preparing the surface for trowelling or smoothing out concrete after it's been poured. Ideal for masonry work and DIY use.

CLAW HAMMER

For general wood working and nail driving.

LAGARING BAKAL

HACK SAW

ROTARY HAMMER

can be used for "doweling" (repetitive drilling of large rebar anchor holes), and drilling through-holes in concrete and masonry walls

HACK SAW

fine-toothed saw, originally and mainly made for cutting metal

WOOD FLOAT

float that is useful when working with really stiff concrete or concrete that is setting up too hard

RIP SAW

for cutting along the wood grain

CROSSCUT SAW

for cutting perpendicular to the wood grain

ROTARY HAMMER

like an electric drill that operates with both rotating and reciprocating actions and is used to drill holes in concrete


संबंधित स्टडी सेट्स

NCLEX-RN examination- Health Assessment

View Set

Ag Technology - Module 8, Ag Technology - Module 7, Module Five - Ag Tech, Module 4 - AG Tech, Ag Tech - Module 3, Module 2 - Ag tech - Measures and Horsepower, and Simple Machines, Ag Technology Quiz 1, Ag Technology Mastery Quiz 2, Module 6 - Ag te...

View Set

Chapter 5 Videos with Assessment

View Set

Water, Homeostasis, & Thermoregulation

View Set

AP Environmental Science | Quiz Questions

View Set

U-world Gen-Chem: Bonding Chemistry #3

View Set

Entrepreneurship Chapter 4 Test Review

View Set