TSM 241

Fill in the blank. In IPv6, all routes are level _____ ultimate routes

1

The graphic shows a network of three routers running OSPF connected as follows. Each router has two neighbors. R1 is connected to R3 via Gigabit Ethernet. R2 is connected to R1 via a serial link. R3 is connected to R2 via a serial link. The networks connected to the routers are listed as follows: Router R1 has a LAN and is connected to R2 and R3 Ethernet LAN network:10.10.0.0/16 Ethernet to R3: 10.11.0.2/16 Serial to R2: 209.165.201.3/29 Router R2 is connected to R1 and R3 Serial to R1: 209.165.201.2/29 Serial to R3: 209.165.200.226/29 Router R3 is connected to R1 and R2 Ethernet to R1: 10.11.0.1/16 Serial to R2: 209.165.200.225/29 Refer to the exhibit. What is the administrative distance value that indicates the route for R2 to reach the 10.10.0.0/16 network?

1

he graphics shows an output after the command show ip nat translations is issued on R1: R1# show ip nat translations Pro Inside global Inside local Outside local Outside global --- 10.0.0.31 192.168.3.5 --- --- tcp 10.0.0.17:1025 192.168.3.33:1025 172.16.20.5:80 172.16.20.5:80 tcp 10.0.0.18:1025 192.168.3.35:1025 172.16.20.5:80 172.16.20.5:80 tcp 10.0.0.28:1024 192.168.10.10:1025 172.16.20.5:80 172.16.20.5:80 tcp 10.0.0.28:1025 192.168.10.15:1025 172.16.20.5:80 172.16.20.5:80 tcp 10.0.0.28:1026 192.168.10.35:1025 172.16.20.5:80 172.16.20.5:80 tcp 10.0.0.31:1025 192.168.3.5:1025 172.16.20.5:80 172.16.20.5:80 Refer to the exhibit. A company has an internal network of 192.168.10.0/24 for their employee workstations and a DMZ network of 192.168.3.0/24 to host servers. The company uses NAT when inside hosts connect to outside network. A network administrator issues the show ip nat translations command to check the NAT configurations. Which one of source IPv4 addresses is translated by R1 with PAT?

192.168.10.35

To enable RIP routing for a specific subnet, the configuration command network 192.168.5.64 was entered by the network administrator. What address, if any appears in the running configuration file to identify this network?

192.168.5.0

Refer to the exhibit. Assuming that the routing tables are up to date and no ARP messages are needed, after a packet leaves H1, how many times is the L2 header rewritten in the path to H2?

2

From left to right, PC is connected to the router RT1 through a switch, RT1 is connected to the Internet cloud, the cloud is connected to the router RT2, and RT2 is connected to a web server through a switch. The PC has a label: PC: Inside local: 10.130.5.76 Inside global: 209.165.200.245 RT1 has two labels: Label 1 - Gi0/0, 10.130.5.1 Label 2 - S0/0/0, 209.165.200.226 RT2 has two labels: Label 1: S0/0/0, 192.0.2.1 Label 2: Gi0/0, 172.16.1.1 The web server has a label: Web server: Inside local: 172.16.1.10 Inside global: 203.0.113.5 Refer to the exhibit. NAT is configured on R1 and R2. The PC is sending a request to the web server. What IPv4 address is the source IP address in the packet between R2 and the web server?

209.165.200.245

Which problem is evident if the show ip interface command shows that the interface is down and the line protocol is down

A cable has not been attached to the port

A router command and output is shown as follows: R1# show ip nat statistics Total translations: 6 (2 static, 4 dynamic, 4 extended) Outside Interfaces: Serial0/2/1 Inside Interfaces: Serial0/2/0 , FastEthernet0/0.10 , FastEthernet0/0.11 , FastEthernet0/0.12 Hits: 3 Misses: 4 Expired translations: 0 Dynamic mappings: -- Inside Source access-list 1 pool NAT refCount 4 pool NAT: netmask 255.255.255.248 start 209.165.200.228 end 209.165.200.230 type generic, total addresses 3 , allocated 1 (33%), misses 0 Refer to the exhibit. A network administrator has just configured address translation and is verifying the configuration. What three things can the administrator verify? (Choose three.)

Address translation is working A standard access list numbered 1 was used as part of the configuration process Two types of NAT are enabled

Which three statements accurately descibe VLAN types?

An 802.1Q trunk port, with a native VLAN assigned, supports both tagged and untagged traffic A management VLAN is any VLAN that is configured to access management features of the switch After the initial boot of an unconfigured switch, all ports are members of the default VLAN

Refer to the exhibit. How did the router obtain the last route that is shown?

Another router in the same organization provided the default route by using a dynamic routing protocol

Which three software packages are available for Cisco IOS Release 15.0

DATA Unified Communications Security

Which DHCP Ipv4 message contains the following information? Destination address: 255.255.255.255 Client IPv4 address: 0.0.0.0 Default gateway address: 0.0.0.0 Subnet mask: 0.0.0.0

DHCPDISCOVER

What is a disadvantage when both sides of a communication use PAT?

End-to end IPv4 traceability is lost

What two license states would be expected on a new Cisco router once the license has been activated? (choose two)

License Type: Permanent License State: Active, In Use

The exhibit contains a PC that is labeled PC1 with an address 192.168.11.11/24. PC1 is connected to switch SW1, which is connected to interface Fa0/0 on router R1. Interface Fa0/1 on R1 is connected to switch SW2. SW2 is connected to PC2, which has an IP address of 192.168.12.1/24. R1 is connected to the Internet through interface S0/0/0, which has an IP address of 209.165.200.1/27. The router is configured thus: R1(config)# ip nat pool NAT-POOL2 209.165.200.5 209.165.200.10 netmask 255.255.255.224 R1(config)# access-list 1 permit 192.168.0.0 0.0.255.255 R1(config)# interface Fa0/0 R1(config-if)# ip nat inside R1(config)# interface Fa0/1 R1(config-if)# ip nat inside R1(config)# interface Serial0/0/0 R1(config-if)# ip nat outside Refer to the exhibit. R1 is configured for NAT as displayed. What is wrong with the configuration?

NAT-POOL2 is not bound to ACL 1

Refer to the exhibit. Which route was configured as a static route to a specific network using the next-hop address

S 10.0.2.0/24 [1/0] via 192.168.2.2

On a switch that is configured with multiple VLAN, which command will remove only VLAN 100 from the switch?

Switch(config)# no vlan 100

The graphic contains the following text: R1(config)# ip dhcp excluded-address 192.168.10.2 192.168.10.9 R1(config)# ip dhcp excluded-address 192.168.10.254 R1(config)# ip dhcp pool LAN-POOL-1 R1(dhcp-config)# network 192.168.10.0 255.255.255.0 R1(dhcp-config)# default-router 192.168.10.1 R1(dhcp-config)# dns-server 192.168.11.5 R1(dhcp-config)# domain-name example.com R1(dhcp-config)# end Refer to the exhibit. If the IP addresses of the default gateway router and the DNS server are correct, what is the configuration problem?

The IP address of the default gateway router is not contained in the excluded address list

Which requirement should be checked before a network administrator performs an IOS image upgrade on a router?

There is sufficient space in flash memory

Fill in the blank The acronym _____ describes the type of traffic that requires a seperate VLAN, strict QoS requirements, and a one-way overall delay less than 150 ms across the network. These restrictions help to ensure traffic quality.

VOIP

What is the name of the layer in the Cisco borderless switched network design that would have more switches deployed than other layers in the network design of a large organization?

access

which command is issued in the VTY line configuration mode to apple a standard ACL that will control Telnet access to a router?

access-class 11 in

A network engineer is configuring PAT on a router and has issued the command: ip nat source list 1 interface serial 0/1/0 overload Which additional command is required to specify addresses from the 192.168.128.0/18 network as the inside local addresses?

access-list 1 permit 192.168.128.0 0.0.63.255

After sticky learning of MAC addresses is enabled, what action is needed to prevent dynamically learned MAC addresses from being lost in the event that an associated interface goes down?

copy the running configuration to the startup configuration

Refer to the exhibit. This network has two connections to the ISP, one via router C and one via router B. The serial link between router A and router C supports EIGRP and is the primary link to the Internet. If the primary link fails, the administrator needs a floating static route that avoids recursive route lookups and any potential next-hop issues caused by the multiaccess nature of the Ethernet segment with router B. What should the administrator configure?

create a fully specified static route pointing to Fa0/0 with an AD of 95

Which type of static route typically uses the distance parameter in the ip route global configuration command?

floating static route

Which statement correctly describes how a LAN switch forwards frames that it receives?

frame forwarding decisions are based on MAC address and port mappings in the CAM table

What is a function of the distribution layer?

interconnection of large-scale networks in wiring closets

The exhibit is an output of the show ip route command on R1 and displays: R1# show ip route | begin Gateway Gateway of last resort is 209.165.200.234 to network 0.0.0.0 S* 0.0.0.0/0 [1/0] via 209.165.200.234, Serial0/0/1 is directly connected, Serial0/0/1 172.16.0.0/16 is variably subnetted, 3 subnets, 2 masks c 172.16.1.0/24 is directly connected, GigabitEthernet0/0 L 172.16.1.1/32 is directly connected, GigabitEthernet0/0 R 172.16.2.0/24 [120/1] via 209.165.200.226, 00:00:12, Serial0/0/0 R 172.16.4.0/28 [120/2] via 209.165.200.226, 00:00:12, Serial0/0/0 <output omitted> Refer to the exhibit. Which type of route is 172.16.0.0/16?

level 1 parent route

A lab in a network management software company is configuring a testing environment to verify the performance of new software with different network connectivity speeds, including FastEthernet, GigabitEthernet, and 10 GigabitEthernet, and with copper and fiber optic connections. Which type of switch should the software company purchase to perform the tests?

modular configuration

Which network design principle focuses on the capability of on-demand seamless network expansion in a switched network

modularity

Refer to the exhibit. Which type of IPv6 static route is configured in the exhibit?

recursive static route

Which type of inter-VLAN communication design requires the configuration of multiple subinterfaces?

router on a stick

What information is added to the switch table from incoming frames?

source MAC address and incoming port number

A company security policy requires that all MAC addressing be dynamically learned and added to both the MAC address table and the running configuration on each switch. Which port security configuration will accomplish this?

sticky secure MAC addresses

Which switching method provides error-free data transmission?

store-and-forward

What command will enable a router to begin sending messages that allow it to configure a link-local address without using a IPv6 DHCP server?

the ipv6 unicast-routing command

What is the minimum configuration for a router interface that is participating in IPv6 routing?

to have only a link-local IPv6 address

a network administrator has entered the following command: ip route 192.168.10.64 255.255.255.192 serial 0/0/1

verify that the serial 0/0/1 interface is active and available