Unit 22 review

अब Quizwiz के साथ अपने होमवर्क और परीक्षाओं को एस करें!

10.Air-cooled condensers are much more efficient than water-cooled condensers.

Answer : (False) Water cooled condensers are much more efficient than air cooled condensers

19.How much higher does a water cooled condenser condense at when using a cooling tower?

Answer : 10F

7.When a standard efficiency air cooled condenser is used the condensing refrigerant will normally be....F higher in temperature than the entering air temp .

Answer : 30F higher than the outside air temp

14.Briefly describe what is meant by floating head pressure and tell why it is used in refrigeration and AC system

Answer : An industry term for attaining the lowest possible condensing pressure is called Floating head pressure. Floating head pressure systems simply let the condensing pressure follow the ambient temperature as the seasons swing from summer to winter.

Recirculating water uses what ? to help the cooling process.

Answer : Evaporation

8.Four methods of controlling head pressure in an air cooled condenser are?

Answer : Fan cycling controls, variable speed fans, shutters and condenser flooding controls

12.Compare the standard conditions of high efficiency and standard air cooled condensers.

Answer : High efficiency would be to have the condenser head pressure as close to the ambient air as possible.

18. Name 3 types of cooling towers?

Answer : Natural Draft, Forced Draft, and Evaporative

16.Explain the basic operations of a combination ORI and ORD low ambient head pressure control valve.

Answer : ORD valve sense a factory preset pressure difference of 20 psi between the receiver and compressor discharge , It will start to open and bypass hot compressor discharge gas to the receivers inlet The ORI valve stows refrigerant in the condenser to maintain the correct head pressure. Both the ORI and the ORD will work in conjunction of one another to maintain proper receiver pressure, regardless of outside temperature.

22.What is the component that rejects heat from the refrigeration system ?

Answer : The Condenser

9.The prevailing winds can affect which of the air cooled condensers?

Answer : The cooling tower

13.Name 2 ways in which the heat from an air cooled condenser can be used for heat reclaim?

Answer : The discharge gas can be passed to the rooftop condenser or to a coil mounted in the duct work that supplies heat to the store.

3.Who should be consulted when condenser cleaning is needed ?

Answer : The manufacturer

5.After heat is absorbed into a condenser medium in a water cooled condenser,the heat can be deposited in one of two places.What are they?

Answer : The water can be used once, then wasted down the drain or where large amounts of water are being used, it is more economical to save water, cool it in an outside water tower and reuse it.

11.The type of condenser that has the lowest operating head pressure is the------ cooled condenser.

Answer : The water cooled condenser

6.A water cooling tower capacity is governed by what aspect of the ambient air?

Answer : The wet bulb temperature of the air

21.Name the 3 types of water cooled condensers.

Answer : Tube within a tube, Shell & coil, Shell & tube

15.Explain how to flush impurities from a water regulating valve that is on a water cooled condenser.

Answer : Water cooled condensers can be cleaned by brush or chemically

20.What must be added to the system to help water when it is evaporating from over concentrating minerals ?

Answer : Water must be added to the system to keep this from happening

17.Name two problems a refrigeration system may have if the condensing unit is exposed to low ambient condition when it is not using a low ambient head pressure control valve

Answer : When the condensing medium is cold enough to reduce the head pressure to the point that the expansion device will starve the evaporator. And less head pressure cause less heat to be available for the heat reclaim coils to heat buildings

1.Why do some condenser have to be cleaned with brushes and others with chemicals

Answer: So the condenser can properly reject heat without going into a high system pressure, The types that have to be clean with chemicals are types that are not excusable

2.What are 3 materials condensers are normally made of ?

Answer: Stainless steel, copper and nickel

When is the most heat removed from the refrigerant in the condensing process.

The greatest amount of heat that is given up from the refrigerant is while the condensing process is taking place, de superheating


संबंधित स्टडी सेट्स

Nutrition Unit 2 Digestion, Absorption and Metabolism

View Set

Common Knowledge Farm Business Management CDE-2019 test

View Set

RMI Chapter 4 Quiz Questions CPCU 500

View Set