Chapter 1-2 OSPFv2
An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 64.102.0.0 255.255.255.128. What wildcard mask would the administrator use in the OSPF network statement?
0.0.0.127
An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 64.100.0.0 255.255.255.0. What wildcard mask would the administrator use in the OSPF network statement?
0.0.0.255
An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 128.107.0.0 255.255.255.192. What wildcard mask would the administrator use in the OSPF network statement?
0.0.0.63
An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 192.168.181.0 255.255.254.0. What wildcard mask would the administrator use in the OSPF network statement?
0.0.1.255
An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 192.168.223.0 255.255.254.0. What wildcard mask would the administrator use in the OSPF network statement?
0.0.1.255
An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 128.107.0.0 255.255.252.0. What wildcard mask would the administrator use in the OSPF network statement?
0.0.3.255
An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 198.19.0.0 255.255.252.0. What wildcard mask would the administrator use in the OSPF network statement?
0.0.3.255
By default, what is the OSPF cost for any link with a bandwidth of 100 Mb/s or greater?
1
What is the default router priority value for all Cisco OSPF routers?
1
What is the recommended Cisco best practice for configuring an OSPF-enabled router so that each router can be easily identified when troubleshooting routing issues?
Configure a value using the router-id command.
Which type of OSPFv2 packet contains an abbreviated list of the LSDB of a sending router and is used by receiving routers to check against the local LSDB?
Database Description
After modifying the router ID on an OSPF router, what is the preferred method to make the new router ID effective?
HQ# clear ip ospf process
To establish a neighbor adjacency two OSPF routers will exchange hello packets. Which two values in the hello packets must match on both routers?
Hello interval Dead interval
Which three OSPF states are involved when two routers are forming an adjacency? (Choose three.)
Init Two-way Down
Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers but PC1 is unable to connect to PC2. What is the most likely problem?
Interface Fa0/0 has not been activated for OSPFv2 on router R2.
Which three statements describe features of the OSPF topology table?
It is a link-state database that represents the network topology. When converged, all routers in an area have identical topology tables. The table can be viewed via the show ip ospf database command.
In an OSPFv2 configuration, what is the effect of entering the command network 192.168.1.1 0.0.0.0 area 0 ?
It tells the router which interface to turn on for the OSPF routing process.
Which OPSF packet contains the different types of link-state advertisements?
LSU
Which OSPF data structure is identical on all OSPF routers that share the same area?
Link-state Database
Refer to the exhibit. On which router or routers would a default route be statically configured in a corporate environment that uses single area OSPF as the routing protocol?
R0-A
Refer to the exhibit. Which command did an administrator issue to produce this output?
R1# show ip ospf interface serial0/0/1
A network engineer has manually configured the hello interval to 15 seconds on an interface of a router that is running OSPFv2. By default, how will the dead interval on the interface be affected?
The dead interval will now be 60 seconds.
What is a benefit of multiarea OSPF routing?
Topology changes in one area do not cause SPF recalculations in other areas.
What is the format of the router ID on an OSPF-enabled router?
a 32-bit number formatted like an IPv4 address
Which step in the link-state routing process is described by a router building a link-state database based on received LSAs?
building the topology table
Which step in the link-state routing process is described by a router inserting best paths into the routing table?
choosing the best route
Which step in the link-state routing process is described by a router sending Hello packets out all of the OSPF-enabled interfaces?
establishing neighbor adjacencies
When an OSPF network is converged and no network topology change has been detected by a router, how often will LSU packets be sent to neighboring routers?
every 30 minutes
Which step does an OSPF-enabled router take immediately after establishing an adjacency with another router?
exchanges link-state advertisements
Which step in the link-state routing process is described by a router flooding link-state and cost information about each directly connected link?
exchanging link-state advertisements
Which step in the link-state routing process is described by a router running an algorithm to determine the best path to each destination?
executing the SPF algorithm
What indicates to a link-state router that a neighbor is unreachable?
if the router no longer receives hello packets
What type of address is 64.101.198.197?
public
An OSPF router has three directly connected networks; 172.16.0.0/16, 172.16.1.0/16, and 172.16.2.0/16. Which OSPF network command would advertise only the 172.16.1.0 network to neighbors?
router(config-router)# network 172.16.1.0 255.255.255.0 area 0
What does an OSPF area contain?
routers that have the same link-state information in their LSDBs
Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?
show ip ospf interface serial 0/0/0
What command would be used to determine if a routing protocol-initiated relationship had been made with an adjacent router?
show ip ospf neighbor
Which command is used to verify that OSPF is enabled and also provides a list of the networks that are being advertised by the network?
show ip protocols
A network technician issues the following commands when configuring a router: R1(config)# router ospf 11 R1(config-router)# network 10.10.10.0 0.0.0.255 area 0 What does the number 11 represent?
the OSPF process ID on R1
What is used to facilitate hierarchical routing in OSPF?
the use of multiple areas
What is a function of OSPF hello packets?
to discover neighbors and build adjacencies between them
What is the reason for a network engineer to alter the default reference bandwidth parameter when configuring OSPF?
to more accurately reflect the cost of links greater than 100 Mb/s
What are the two purposes of an OSPF router ID? (Choose two.)
to uniquely identify the router within the OSPF domain to facilitate router participation in the election of the designated router
In an OSPF network when are DR and BDR elections required?
when the routers are interconnected over a common Ethernet network
