Check for Understanding 12

Lakukan tugas rumah & ujian kamu dengan baik sekarang menggunakan Quizwiz!

What causes an unwanted mark (dark ghosting) to appear on printed pages? Select one: a. A damaged laser b. A damaged toner c. A damaged head d. A damaged drum

a damaged drum

In a laser printer, what must be done to the drum to make it receptive to new images? Select one: a. It must be sterilized and decontaminated. b. It must be grounded and fully discharged. c. It must be charged with a uniform positive charge. d. It must be charged with a uniform negative charge.

a?

What kind of printer is used with multipart forms such as those with point of sale machines? Select one: a. Dot-matrix b. Daisy-wheel c. Inkjet d. Color

dot-matrix

How is laser printer resolution measured? Select one: a. Color per inch b. Dots per inch c. Pixels per inch d. Bits per inch

dots per inch

You are printing from a dot-matrix printer and notice that the characters look chopped off at the top. What should you try adjusting? Select one: a. Toner b. Driver c. Cartridge d. Drum

driver

Printers can use _______________, which enable the printer to automatically print on both sides of the paper. Select one: a. bidirectional assemblies b. document feeders c. duplex assemblies d. fuser assemblies

duplex assemblies

In a laser printer, the pressure roller and heated roller are used to _______________. Select one: a. melt the toner to the paper b. fuse the toner to the paper c. burn the toner to the paper d. apply the toner to the paper

fuse the toner to the paper

In a laser printer, the _______________ uses friction to isolate a single sheet from any others that were picked up. Select one: a. duplexing assembly b. separation pad c. transfer roller d. gearbox

separation pad

Laser printers are particularly effective for printing _______________. Select one: a. spot color b. full-color images c. complex images d. 256-bit color

spot color

What does the primary corona wire charge? Select one: a. The fuser assembly b. The paper c. The toner d. The drum

the drum

The fuser assembly in a laser printer is almost always separate from the _______________. Select one: a. laser head b. gearbox c. drum d. toner cartridge

toner cartridge

In laser printers, what component applies a positive charge to the paper, drawing the negatively charged toner particles to the paper? Select one: a. Transfer corona b. Turning gears c. Laser d. Toner

transfer corona

What charges the paper in a laser printer? Select one: a. Primary corona b. Transfer corona c. Fuser assembly d. Laser

transfer corona

The term sublimation means to cause something to change from a solid into a _______________ form and then back into a solid. Select one: a. vapor b. viscous c. liquid d. crystal

vapor

The Hewlett-Packard system for controlling printers is _______________. Select one: a. PCL b. PostScript c. ASCII d. Unicode

ASCII

What Control Panel applet is used to manage printers and faxes in Windows 7/8/8.1? Select one: a. Devices and Printers b. Hardware c. Printers and Faxes d. Printers and Hardware

Devices and Printers

What kind of printer uses a grid of tiny pins, also known as printwires, to strike an inked printer ribbon and produce images on paper? Select one: a. Dot-matrix b. Inkjet c. Laser d. Thermal

Dot-matrix

What are 9-pin dot-matrix printers generically called? Select one: a. Economy quality b. Near-letter quality c. Draft quality d. Letter quality

Draft qualiyu

Which printer transfers data to the printer one character or one line at a time? Select one: a. Impact b. Laser c. Dye-sublimation d. Thermal

Impact

What kind of printers tend to have problems with ink drying out inside the nozzles when the printer is not used for a period? Select one: a. Color b. Laser c. Inkjet d. Dot-matrix

Inkjet

What type of printer works by ejecting ink through tiny tubes? Select one: a. Laser b. Inkjet c. Dot-matrix d. Impact

Inkjet

During the laser printer process, after the erase lamp exposes the entire surface of the photosensitive drum to light, what happens to the photosensitive coating? Select one: a. It becomes bright. b. It becomes electrically charged. c. It becomes conductive. d. It becomes nonconductive.

It becomes conductive

Most printers, scanner, and multifunction devices connect to a computer via a(n) _______________. Select one: a. proxy server b. FireWire port c. Ethernet cable d. USB port

USB port

At the end of the laser printing process, what is cleaned? Select one: a. Toner b. Laser head c. Photosensitive drum d. Power unit

photosensitive drum

The toner in a laser printer is a fine powder. This powder is made up of plastic particles bonded to _______________ particles. Select one: a. nickel b. polyester c. aluminum d. pigment

pigment

Toner particles are composed mostly of _______________, which allows them to be melted to the page. Select one: a. carbon b. power c. plastic d. Teflon

plastic

Laser printers usually use a laser as the light source because of their _______________. Select one: a. intensity b. brightness c. precision d. cost-effectiveness

precision

Assuming a printer is in good working order and online, what should you check next if nothing prints? Select one: a. Calibration b. Port settings c. Printer emulation d. Print spooler

print spooler

A laser printer creates an image of dots and holds it in memory before printing it. What is this image of dots called? Select one: a. Raster image b. Laser image c. Vector image d. High-resolution image

raster image

How are dots put onto the surface of paper from a direct thermal printer? Select one: a. Through spraying b. By etching c. Through embedding d. By burning

By burning

The dye-sublimation printing technique is an example of what method of color printing? Select one: a. PPM b. RGB c. CMYK d. LEDS

CMYK

What should you do if your dot-matrix printer output is covered with dots and small smudges? Select one: a. Replace the drum. b. Clean the platen. c. Clean the printhead. d. Replace the cartridge.

Clean the platen

What should be added to a laser printer to resolve a memory overflow problem? Select one: a. RET b. RIP c. ROM d. RAM

RAM

What kind of chip is used by a laser printer to translate the raster image sent to the printer into commands for the laser? Select one: a. RAM b. RIP c. ROM d. UART

RIP

When a thermal printhead passes over the film ribbon, what melts onto the paper? Select one: a. Wax b. Toner c. Dye d. Ink

Wax

What kind of printer creates an image on paper by physically striking an ink ribbon against the paper's surface? Select one: a. Laser b. Dot-matrix c. Thermal d. Impact

impact

What element is heated by tiny resistors or electroconductive plates at the end of each tube in an inkjet printer? Select one: a. Ink b. Toner c. Toner powder d. Nozzle

ink

In a laser printer, what component is used to write a positive image on the surface of the drum? Select one: a. Toner b. Marker c. Laser d. Head

laser

What kind of printer relies on a photoconductive process? Select one: a. Dot-matrix b. Inkjet c. Laser d. Thermal

laser

What needs to be vacuumed or replaced periodically in a laser printer? Select one: a. Ozone filter b. Drum c. Toner cartridge d. Powder

ozone filter


Set pelajaran terkait

Time Period 4~ Chapter 7 Apush Quiz MCQ

View Set

Study Questions for Auto Cad 3 Test 2

View Set

EXAM #4 - CH. 16, 21, 23, 27, 56

View Set

Ethical Hacking Chapter 9 Web and Database Attacks

View Set