Electrical Motor Controls, Chapters 21-30 Tech-Cheks
Even at full conduction, an SSR presents some residual resistance, which can create a voltage drop of up to approximately _____ V in the load circuit.
1.5
A voltage-output pressure sensor typically outputs 0 VDC to _____ VDC proportional to the rating of the pressure sensor.
10
A current-output pressure sensor typically outputs 4 mA to _____ mA proportional to the rating of the pressure sensor.
20
The high-frequency sound waves of an ultrasonic sensor are typically in the _____ kHz range.
200
Cold resistance is measured at _____ °C
25
_____ drives are the most common drives because they can easily vary the speed of a 3 phase motor.
AC
_____ sensors can detect materials such as plastic, glass, water, moist wood, etc.
Capacitive
Pressure sensors are suited for a wide variety of pressure measurements on _____, pumps, and other similar equipment.
Compressors
_____ current glow is the movement of electrons from positive to negative.
Conventional
The _____ flowing through a photodiode increases as the resistance decreases.
Current
_____ is one of the most suitable industrial applications of SCRs.
DC motor control
_____ mode is a method of ultrasonic sensor operation in which the emitter and receiver are placed opposite each other so that the sound waves from the emitter are received by the receiver.
Direct
The operation of a thermistor is based on the _____ -hole theory.
Electron
_____ is a ratio of the amplitude of an output signal to the amplitude of an input signal.
Gain
_____ is a phenomenon that occurs when a relay fails to turn off because the current and voltage in the circuit reach zero at different times.
Half-waving
A(n) _____ sensor detects the proximity of a magnetic field.
Hall effect
_____ actuation is an active method of Hall effect sensor activation in which a magnet is oriented perpendicular to the surface of the sensor and is usually centered over the point of maximum sensitivity.
Head-on
_____ trip is the trio point after the overloads have tripped and have been reset (motor operating near or over nameplate rated current).
Hot
_____ and contamination are the primary causes of photocell failure.
Humidity
_____ heated thermistors are used for precision temperature measurement and temperature compensation.
Indirectly
The primary difference between a photodiode and a regular diode is that a photodiode has an addition of a _____ in it's housing for focusing light on the PN junction.
Lens
A photoconductive cell (photocell) is a device that conducts current when energized by _____
Light
_____ current is the amount of current drawn by a load when energized.
Load
With a(n) _____ thermistor, an increase in temperature causes the resistance of the thermistor to decrease.
NTC
_____ error is a slight mismatch between internal components.
Offset
_____ control is the control of the time relationship between two events when dealing with voltage and current.
Phase
Without light, the _____ of the photodiode is high.
Resistance
A photocell is, in effect, a variable _____
Resistor
_____ scan is a method of scanning in which the transmitter and receiver are housed in the same enclosure and the transmitted light beam is reflected back to the receiver from the reflector.
Retroflective
_____ start is the most common solid-state starting method.
Soft
_____ stop is the most common solid-state motor starter stopping method.
Soft
_____ scan distinguishes between shiny and nonshiny (matte) surfaces.
Specular
A thermistor is a(n) _____ -sensitive resistor.
Temperature
_____ is the largest problem in applications that use an SSR.
Temperature rise
A flow detection sensor operates on the principle of _____ conductivity.
Thermal
A(n) _____ switching relay has a built-in synchronizing circuit that controls the amount of output voltage as a function of the input voltage.
analog
An op amp is often used in digital circuits that require the _____ amplification of a weak signal.
analog
Hall voltage varies depending on how close the magnet is to the Hall generator, which acts as a(n) _____ signal.
analog
The _____ starting method provides the highest possible starting torque per ampere of line current and is the most effective means of motor starting for applications where the inrush current must be reduced with a minimum sacrifice or starting torque.
autotransformer
The N-type material in a unijunction transistor functions as the _____ and has two leads.
base
In a two-lead phototransistor, the _____ is replaced by a clear covering that allows light to fall on the base region.
base lead
In any transistor circuit, the _____ junction must always be forward biased.
base/emitter
A _____ device is a device in which both holes and electrons are used as internal carriers for maintaining current flow.
bipolar
A gate current is used to reduce the level of _____ voltage necessary for an SCR to conduct or fire.
breakover
Amplifiers connected together are called _____ amplifiers.
cascaded
The _____ method is a method of SSR replacement in which a logical sequence is used to determine the reason for a failure.
circuit analysis
The _____ is the first layer of protection for the glass or plastic core of an optical fiber cable.
cladding
A(n) _____ system may have automatic correction control.
closed-loop
An SSR circuit consists of an input circuit, a _____ circuit, and an output circuit.
control
It is possible for small amounts of _____ (OFF-state leakage) to pass through an SSR because some conductance is still possible even though the SSR is turned off.
current
The _____ region is the point at which the transistor is turned off and no current flows.
cutoff
As electrons move across the _____ of a light-emitting diode (LED), they give up extra kinetic energy, which is converted to light.
depletion region
Generally, any material with a _____ constant greater than 1.2 may be detected.
dialectric
An optocoupler uses a glass _____ sandwich to separate input from output.
dielectric
The _____ provides wide bandwidth and high impedance in an op amp.
differential amplifier
When transistors are used as switches, a _____ can be mounted across the transistor to prevent damage from high-voltage spikes (transients).
diode
The best scanning method for height and distance monitoring is _____ scan with modulated controls.
direct
The input circuit is deactivated when a voltage less than the specified minimum _____ voltage of the relay is applied.
dropout
Inductive proximity sensors operate on the _____ principle.
eddy current killed oscillator
The _____ light beam is the area of light that travels directly from the transmitter to the receiver.
effective
Communication is the transmission of information from one point to another by means of _____ waves.
electromagnetic
A proximity sensor (proximity switch) is a solid-state sensor that detects the presence of an object by means of a(n) _____ sensing field.
electronic
The input of a common-_____ circuit is across the base and emitter, while the load is across the collector and emitter.
emitter
Since a(n) _____ MOSFET does not conduct at zero gate voltage, it is often called a normally off MOSFET.
enhancement
The main body of a(n) _____ MOSFET is composed of a highly resistive P-type material.
enhancement
An RC circuit is a circuit in which resistance (R) and capacitance (C) are used to help _____ the power in a circuit.
filter
A(n) _____ serves as the control point for an SCR.
gate
The two sections of P-type material constitute the _____ of a JFET.
gate
Problems with IGBTs and other solid-state switches can be reduced by keeping their _____ clean for proper airflow movement.
heat sinks
Triacs cannot replace SCRs in _____ applications.
high-current
JFET's are used extensively in circuits where low power and high _____ are factors.
impedance
A(n) _____ proximity sensor is a sensor that detects only conductive substances.
inductive
The "PIN" in PIN photodiode stands for P-type material, _____, and N-type material.
insulator
The _____ resistance measurments taken when troubleshooting IGBT's are used to determine whether the resistance is too low and the device is defective.
leakage
Hall effect sensors are also used to replace mechanical _____ switches in applications that require the detection of an object's position.
limit
In a(n) _____ light source, the light source is turned on and off at a very high frequency, normally several kilohertz (kHz).
modulated
A solid-state motor starter is an electronically operated switch (contactor) that uses solid-state components to eliminate mechanical contacts and includes _____.
motor overload protection
Because there is a small delay (usually less than 30 sec) before a flow detection sensor heats enough to signal no flow, the sensor acts like a _____, which allows for a short time delay to pass before signaling a problem.
motor starter overload
A diac has _____ resistance because it does not conduct current until the voltage across it reaches breakover voltage.
negative
A(n) _____ is needed to properly test an SCR under operating conditions.
oscilloscope
In darkness, a phototriac is not triggered. The remaining leakage current is referred to as _____ current.
peak blocking
A fiber optic receiver normally contains a(n) _____ that converts light back into electrical signals.
photodiode
Typical Hall effect sensor package configurations include cylinder, proximity, vane, and ____.
plunger
One disadvantage of an IGBT is that the switching speed is inferior to that of a(n) _____ MOSFET.
power
One of the significant advantages of an SSR over an EMR is its _____.
response time
An important feature of triacs is the absence of a(n) _____ condition of high voltages and high current, such as those found in diodes and SCRs.
reverse breakdown
As long as the emitter voltage remains less than the internal voltage, the emitter junction will remain _____, even at a very high voltage.
reverse-biased
Triacs are the equivalent of two SCRs connected in a _____ arrangement with gates also connected to each other.
reverse-parallel
Materials such as foam, fabric, and _____ are difficult for ultrasonic sensors to detect and are better detected by photoelectric or proximity sensors.
rubber
A flow detection sensor is a sensor that detects the movement (flow) of liquid or gas using a(n) _____.
solid-state device
A typical solid-state _____ circuit consists of both start and run contractors connected in the circuit.
starting
Triacs, diacs, UJTs, and SCRs operate only as _____.
switches
Photoelectric sensors that switch DC circuits normally use _____ as the switching element.
transistors
A UJT is typically used as a triggering circuit for a _____ or similar device.
triac
Diacs are used almost exclusively as _____ devices.
triggering
A JFET is a(n) _____ device.
unipolar
The main difference in operation between a JFET and MOSFET is that _____ is applied between the gate and the P and N regions of the MOSFET structure.
voltage
A _____ is a noninverting amplifier.
voltage follower
Electrically, a diac operates in a manner similar to two _____ that are connected in series in opposite directions.
zener diodes
The _____ switching relay is the most widely used relay.
zero