INFX 240 test 2

You have a network that's connected using a physical star topology. One of the drop cables connecting a workstation has been removed. Which of the following BEST describes the effect that this will have on network communications?

All devices except the device connected with the drop cable will be able to communicate

During a network infrastructure upgrade, you replaced two 10 Mbps hubs with switches and upgraded from a Category 3 UTP cable to a Category 5e. During the process, you accidentally cut the Cat 5e patch cable that stretches from the network printer to the upgraded switch. What is the impact on your network?

All network nodes except the printer will be available

You are implementing a SOHO network for a local business. The ISP has already installed and connected a cable modem for the business. The business has four computers that need to communicate with each other and the internet. The ISP's cable modem has only one RJ45 port. You need to set up the network within the following parameters: You must spend as little money as possible. You must not purchase unnecessary equipment. Computers need to have a gigabit connection to the network. New devices should not require management or configuration. You examine each computer and notice that only one of the four computers has a wireless NIC. They all have Ethernet NICs. What should you purchase?

An unmanaged switch and CAT 5e cabling

You are moving a client to a new location within an Ethernet network. Previous to the move, the client system did not have difficulty accessing the network. During the relocation, you attach patch cables from the client system to the wall jack and from the patch panel to the switch. Once connected, you do not get a link light on the network card or the switch. You swap out the cable running between the patch panel and the switch with a known good one, but you still cannot connect. Which of the following might you suspect is the problem?

Failed patch cable between the client system and wall jack

Upon conducting a visual inspection of the server room, you see that a switch displays LED collision lights that are continually lit. You check the LED on the corresponding workstation and see that it is flashing rapidly even though it is not sending or receiving network traffic at that time. What is the cause of the network collisions?

Faulty network card

Which type of cabling do Ethernet 100BaseFX networks use?

Fiber optic

IPAM

IP address management is an integrated set of tools that enable (end-to-end planning) deploying, managing, and monitoring IP addresses.

Bridges

Internetworking devices that connect to different LANs and make them appear to be one

You have a network that's connected using a physical bus topology. One of the cables that connects a workstation to the bus breaks. Which of the following BEST describes the effect that this will have on network communications?

No devices will be able to communicate

Which of the following connectors is typically used for the ends of a rollover cable?

RJ45

Which of the following standards does a rollover cable typically use?

RS232

A user from the sales department calls to report that he is experiencing problems connecting to the sales file server. All users in the sales department connect to this server through a single Ethernet switch. No other users have reported problems connecting to the sales server. Which of the following troubleshooting actions are you MOST likely to perform first?

Replace the network card in the user's computer.

You have purchased a new router that you need to configure. You need to connect a workstation to the router's console port to complete the configuration tasks. Which type of cable would you most likely use?

Rollover

Which of the following connections would you use a straight-through cable for? Correct Answer: Router to the uplink port on a hub

Router to a regular port on switch

You would like to implement 10 Gbps Ethernet over a distance of 1 kilometer or greater. Which of the following would be the minimum requirement for this implementation?

Single-mode fiber, 10GBaseLR standards

You need to connect a workstation to a switch using a regular port on the switch (not an uplink port). The switch does not support auto-MDI. Which type of cable should you use?

Straight-through

Angela is the network administrator for a rapidly growing company with a 100BaseT network. Users have recently complained about slow file transfers. While checking network traffic, Angela discovers a high number of collisions. Which connectivity device would BEST reduce the number of collisions and allow future growth?

Switch

Class B network

TCP/IP is a network that uses addresses from 128 to 191 and supports up to 16,384 subnets with 65,534 unique hosts each. 8 bits identifies the network

Class A network

This IP class is used where there are a large number of hosts.

VLSM

Variable length subnet masking a segmented piece of a larger network strategy where all subnet masks can have varying sizes

VLAN

Virtual local area network. A VLAN can logically group several different computers together, or logically separate computers, without regard to their physical location. It is possible to create multiple VLANs with a single switch.

cache

a chip-based computer component that makes retrieving data from memory more efficient at acts as temporary storage over that the computer's processor can retrieve data more easily.

DNS records

a database of records used to map a URL to an IP address. DNS records are stored in the DNS server and work to help users connect to their website

Unicast

a form of message delivery in which a message is delivered to a single destination

subnetting

a net work inside a network, they make networks more efficient, through subnetting, network traffic can travel shorter distance without passing through unnecessary routers to reach its destination

DHCP(Dynamic Host Configuration Protocol)

a network protocol that is used to configure network devices to communicate with an IP network

Octet

each of the decimal numbers in an IP address

Advantages of CIDR

enables routers to reach network traffic destinations much more quickly. Also allows the amalgamation of subnets into a supernet for more efficient network routing. One routing table entry represents the entire aggregation of networks.

subnet mask

is used to divide an IP address into 2 parts 1st part- Identifies the host computer 2nd part- identifies the network to which it belongs,

Multicast

simultaneous transmission of multiple channels of compressed content or the same content but at different times

L2 Switch

widely used n companies and enterprises netowrks

Which of the following physical topologies are used with Ethernet networks?

Bus, Star

CIDR

Classless Inter-Domain Routing

Which of the following is true about half-duplex mode?

Collision detection is on

You want to create a loopback plug using a single RJ45 connector. How should you connect the wires in the connector?

Connect pin 1 to pin 3 and pin 2 to pin 6

You want to create a rollover cable that has an RJ45 connector on both ends. How should you connect the wires within the connectors?

Connect pin 1 to pin 8, pin 2 to pin 7, pin 3 to pin 6, and pin 4 to pin 5

You need to connect two switches using their uplink ports. The switches do not support auto-MDI. Which type of cable should you use?

Crossover

You need to transfer data from one laptop to another, and you would like to use an Ethernet cable. You do not have a hub or a switch. Which type of cable should you use?

Crossover

You want to connect the LAN port on a router to the uplink port on a switch. The switch does not support auto-MDI. Which type of cable should you use?

Crossover

You have a network that's connected using a full physical mesh topology. The link between Device A and Device B is broken. Which of the following BEST describes the effect that this will have on network communications?

Device A will be able to communicate with all other devices

DDNS

Dynamic Domain Name System

4 bits

1 byte

properties of star topology

1. Can connect switches to each other and to host using point-to-point links, which means that we can build net works of longer geographical 2. Adding a new host to the network by connecting it to a switch, does not reduced the reinforcement of the network for other hosts.

Your network follows the 100Base-TX specifications for Fast Ethernet. What is the maximum cable segment length allowed?

100 meters

Which Gigabit Ethernet standard uses multimode fiber optic cabling and supports network segments up to a maximum of 550 meters long?

1000Base-SX

Which Gigabit Ethernet standard can support long network segments up to a maximum of 5 km when used with single-mode fiber optic cable?

1000BaseLX

You want to implement an Ethernet network at very long distances using fiber optic cables. Which standard and cable type would you choose?

1000BaseLX, Single-mode fiber

ou have been tasked with designing an Ethernet network. Your client needs to implement a very high-speed network backbone between campus buildings, some of which are around 300 meters apart. Multimode fiber optic cabling has already been installed between buildings. Your client has asked that you use the existing cabling. Which Ethernet standard meets these guidelines?

10GBase-SR, 1000Base-SX

Your network follows the 100Base-FX specifications for Fast Ethernet and uses half-duplex multimode cable. What is the maximum cable segment length allowed?

412 meters

Class C network

A TCP/IP network that uses addresses from 192 to 223 and supports up to 2,097,152 subnets with 254 unique hosts each.

switch

A device for making, breaking, or changing the connections in an electrical circuit. uses Star topology

You have just connected four new computer systems to an Ethernet switch using spare patch cables. After the installation, only three systems are able to access the network. You verify all client network settings and replace the network card in the failed system. The client is still unable to access the network. Which of the following might you suspect is the real cause of the problem?

Failed patch cable