Intro to Auto Final

Lakukan tugas rumah & ujian kamu dengan baik sekarang menggunakan Quizwiz!

Ten dollars per hour is about how much income per year?

$20,000

A beginning service technician earns $400 dollars per week. How much should the technician spend on a vehicle payment?

$400 per month

If the tenth character represents the year of the vehicle. If the tenth character is a "Y," what year is the vehicle?

2000

The additives used in coolants such as the dye and anticorrosion additives are about what percentage of the coolant?

3%

When using compressed air and a blow gun, what is the maximum allowable air pressure?

30 psi

A V-type engine could have how many cylinders?

4, 6, 8

When mounting an engine to an engine stand, what grade of bolt should be used?

5 or8

A bolt that requires a 1/2 in. wrench to rotate is usually what size when measured across the threads?

5/16 inch

Automotive service systems are generally separated into how many content areas?

8

How many ASE certification tests must be passed to become a master automotive technician?

8

Most vehicle manufacturers specify a lug nut (wheel nut) tightening torque specification of about

80lb-ft to 100lb-ft

Hearing protection should be worn anytime the noise level exceeds _________

90 decibels

One cylinder of an automotive four-stroke cycle engine completes a cycle every ________.

90°

Which description best fits the role of a service advisor?

A customer service representative

The fluid used in power steering systems is

Automatic transmission fluid or special power steering fluid

Hotline services are

Available for a service fee

Which bulb uses natural amber glass? A) 194 B) 194NA C) 168 D) 1157

B) 194NA

If a 2057 bulb is burned out, which bulb should be used to replace it? A) 1157 B) 2057 C) 2057NA D) 3057

B) 2057

Which unit of electricity actually measures the amount of current flow? A) Volt B) Ampere C) Ohm D) Coulomb

B) Ampere

A bulb is being measured using an ohmmeter and the meter display shows OL. This means that the bulb is __________ A) Good B) Bad C) Normal for a tail light bulb but not a brake light bulb D) Partially bad (will be dimmer than normal)

B) Bad

What battery is used mostly when testing a battery to see if it is performing normally? A) CA B) CCA C) MCA D) Reserve capacity

B) CCA (cold cranking amp)

A lane departure warning system uses ___________. A) Radar to determine where the road is located B) Cameras to infrared sensors C) GPS to determine the location of the vehicle on the road D) All of the above are used

B) Cameras to infrared sensors

A type of electronic battery testing that does not place a load on the battery is called __________. A) VAT test B) Conductance tester C) Load tester D) Ammeter tester

B) Conductance tester

What is the symbol for voltage used in calculations? A) R B) E C) EMF D) I

B) E

Starters rotate the engine by a _________. A) Drive belt B) Gear C) Chain D) Shaft from the engine crankshaft

B) Gear

Which type of headlight has a blue color? A) Halogen B) HID (xenon) C) Sealed beam D) None of the above

B) HID (xenon)

An electrical conductor is an element with ______________ electrons in its outer orbit. A) Less than 2 B) Less than 4 C) Exactly 4 D) More than 4

B) Less than 4

The letters "NA" on a light bulb trade number means __________ A) Not available B) Natural Amber C) Not applied D) Any of the above depending on the bulb

B) Natural Amber

Like charges _____________. A) Attract B) Repel C) Neutralize each other D) Add

B) Repel

If an insulated wire rubbed through a part of the insulation and the wire conductor touched the steel body of a vehicle, the type of failure would be called ________. A) Short-to-voltage B) Short-to-ground C) Open D) Chassis ground

B) Short-to-ground

Which circuit failure is most likely to cause a fuse to blow? A) Open B) Short-to-ground C) Short-to-voltage D) High resistance

B) Short-to-ground

Technician A says that a navigation system uses cell phone tower information to locate the vehicle on streets and highways. Technician B says the system uses satellite. Which technician is correct? A) Technician A only B) Technician B only C) Both technicians A and B D) Neither technicians A nor B

B) Technician B only

A technician replaced a 1157NA with a 1157A bulb. Which is the most likely result? A) The bulb is brighter because the 1157A candlepower is higher B) The amber color of the bulb is a different shade. C) The bulb is dimmer because the 1157A candlepower is lower D) Both B and C

B) The amber color of the bulb is a different shade

When jump starting, __________. A) The last connection should be the positive post of the dead battery B) The last connection should be the engine block of the dead vehicle C) The alternator must be disconnected on both vehicles D) Both A and C

B) The last connection should be the engine block of the dead vehicle

As temperature increases _________. A) The resistance of a conductor decreases B) The resistance of a conductor increases C) The resistance of a conductor remains the same D) The voltage of the conductor decreases

B) The resistance of a conductor increases

As the length of a wire increases, _______. A) The resistance of a wire decreases B) The resistance of a wire increases C) The resistance of a wire remains the same D) The voltage of the wire decreases

B) The resistance of the wire increases

The ___________ is a unit of electrical pressure. A) Coulomb B) Volt C) Ampere D) Ohm

B) Volt

Who is the person that greets the service customer and completes the work order? a. Service Manager b. Service Advisor c. Service Writer d. Both B and C

Both B and C

Two technicians are discussing inspection of the transmis-sion pan. Technician A says that some friction material at the bottom of the pan is normal. Technician B says that if any metal parts stick to a magnet then further investigation is needed to determine the cause. Which technician is correct?

Both Technicians A and B

Two technicians are discussing the need for the history of the vehicle. Technician A says that an accident could cause faults due to hidden damage. Technician B says that some faults could be related to a previous repair. Which technician is correct?

Both Technicians A and B

Technician A says that disc brake pads should be replaced when worn to minimum allowable thickness. Technician B says the wear indicator will start making a noise when the brake pads are worn down to the thickness requiring replacement. Which technician is correct

Both technician A and B

Tire inflation is very important to the safe and economi-cal operation of any vehicle. Technician A says that if the pressure is too high, the ride will be stiffer. Technician B says that if the pressure is too low, the tires will wear more on both outside edges. Which technician is correct?

Both technician A and B

Technician A says that the lower the bin number is, the less emissions the vehicle produces. Technician B says that SULEV has cleaner standards than ULEV. Which technician is correct?

Both technicians A and B

Alternators are driven by a __________. A) Drive belt B) Gear C) Chain D) Shaft from the engine crankshaft

D) Shaft from the engine crankshaft

A technician should do all of the following to prepare to take the ASE certification test except. a. get a good nights sleep the night before the test b. try to keep work schedule light the day of the test c. eat a big meal d. have photo id and entry ticket

Eat a big meal

Which type of trouble light is recomeneded for use in the shop?

Either b or c

Which component is NOT part of the chassis system?

Electrical system

If the first character of the VIN is an "S," where was the vehicle made?

England

An under vehicle inspection includes checking for _______.

Exhaust system faults such as broken hangers or leaks, Torn drive axle shafts rubber boots, Any fluid leaks

One of the deductions from a paycheck is for Social Security. This item is usually shown on the pay stub as _______

FICA

The viscosity of engine oil is found where?

Factory service manual or service info, owners manual, lubrication guide

Component location can be found in

Factory service manuals

Wiring diagrams are usually found where?

Factory service manuals

ASE tests require knowledge of vehicle specifications for spark plug gap?

False

A type of test question NOT asked on the ASE certification test is _______

Fill in the blank

Which item is generally not included in a first aid kit? a. eye wash solution b. antibiotic cream c. fire blanket d. bandages

Fire blanket

What type of manual includes time needed to perform service procedures?

Flat-rate manuals

Aftermarket parts catalogs can be a useful source of information and they are usually

Free

A vehicle with the engine in the front can be

Front wheel drive, Rear wheel drive, Four wheel drive

The type of frames used include

Full frame, ladder frame, stub-type frame

The marks on the heads of bolts indicate __________?

Grade and Tensile Strength

A grease fitting can be called

Grease fitting, Alemite fitting, Zerk fitting

The fitting that is used to install grease into a steering or suspension part is called

Grease fitting, alemite fitting, zerk fitting

What is NOT the duty of a general service technician?

Have the customer sign the work order

All overhead valve engines ________.

Have the valves located in the cylinder head

Tall safety stands would be used to

Help support the vehicle when a major component is removed from the vehicle

Which type of lubricant is usually not used in a manual transmission/ transaxle

High-temperature chassis grease

The VECI label includes all except

Horsepower and torque rating of the engine

Spraying accessory drive belts with a fine mist of water from a spray bottle is used to

Is used to check if a noise is due to a belt

The 92 in the tire designation in question 3 refers to the tire's

Its load rating

A tire is labeled 215/60RX17 92T; the T indicates

Its speed rating

The SAE standard for hoist location is

JRP-2184

A safety stand is also called a

Jack stand

Which activity does not allow a person to perform any work while at the shop? a. Cooperative Education Program b. Apprenticeship Program c. Job shadowing d. Part-time employment

Job shadowing

The proper term for Vise Grips are _________

Locking pliers

Many vehicles do not require chassis lubrication if they are equipped with

Low-friction suspension joints such as ball joints, no grease fittings, sealed for life joints

Why is having a good driving record good for the shop?

Lowers insurance costs

Which of the following is a metric bolt? a. 5/16 -18 b. 1/2 - 20 c. M12 - 1.5 d. 8mm

M12 - 1.5

Commonly damaged areas of a vehicle during hoisting include

Rocker panels, exhaust systems, tires or body panels

The torque converter

Rotates at the same speed as the engine, allows the vehicle to creep when the brakes are released, includes a clutch to improve fuel economy

Exposure to asbestos dust can cause what condition?

mesothelioma lung cancer asbestiosis

The threat pitch of a bolt is measured in what units?

millimeters and threads per inch

which type of pliers is capable of fitting of large objects?

multi groove adjustable pliers

Which oil specification stands for the thickness (viscosity)?

SAE

Which oil standard is displayed on the front of the oil container?

SAE

To retrieve stored diagnostic trouble codes, a service technician needs a _______?

Scan tool

The rotation of the steering wheel causes which part to move the actual steering linkage in a rack-and-pinion

Sector Shaft

Which job would be concerned with working hours and pay?

Service Manager

A service advisor is called a _______?

Service Writer

A mentor performs all of the following EXCEPT __________ a. Helps guide diagnosis of a problem b. signs paychecks c. offers advice on how to do a job d. advises on professional behavior

Signs paychecks

To check a crankshaft journal for out-of-round, the journal should be measured in at least how many locations?

Six

To directly measure the diameter of a valve guide in a cylinder head, use a micrometer and a?

Small-hole gauge

Wetted asbestos dust is considered to be ____________

Solid waste

The process of combustion occurring without an open flame is __________

Spontaneous combustion

Which of the following cannot be measured using a straight, edge and a feeler gauage?

Straightness of the cylinder bore

Which type of suspension uses two control arms?

Strut, leaf spring, SLA

A planetary gear set includes a

Sun gear

A screw that can make its own threads when install is called a ___________ screw?

Tapered or Self-Tapping

Tech A or B cleaning threads?

Tech A

Technician A says that customer-pay rate is sometimes higher than factory flat-rate. Technician B says that factory flat-rate times are usually longer (given more time) compare to aftermarket flat-rate time guides. Which technician is correct?

Tech A only

Technician A says that you should guess if you do not know the correct answer. Technician B says that ASE will send you the correct answers to questions you missed with your test results. Which technician is correct?

Tech A only

What is the function of the clutch

To disconnect the engine from the transmission/trans-axle to permit the engine to remain running when the vehicle is stopped, To permit the transmission/transaxle to be shifted, To connect and transmit engine torque to the trans-mission/transaxle

Which part takes the place of a clutch in an automatic trasnmission

Torque converter

A four-wheel drive vehicle often uses a _______ to transmit torque to all four wheels.

Transfer Case

What has to be removed to replace the filter on most automatic transmissions/transaxles

Transmission pan, torque converter, drive shaft or drive axle shaft

What does the "T" mean in the designation 41TE

Transverse

A MacPherson strut is a structural part of the vehicle. True or False

True

How many rotation of the crankshaft are required to complete each stroke of a four-stroke cycle engine

Two

To check a crankshaft journal for taper, the journal should be measured in at least how many locations?

Two

The cabin filter can be accessed from

Under the dash on some vehicles, Under the hood on some vehicles

Uneven tire wear can be caused by

Underinflation, overinflation, wheel alignment problem

The tenth character of a VIN number is the country of origin. Where was the vehicle built that has a 5 as the first character

United States

Which part in the steering column allows for changes in the angle between the upper and lower shafts?

Universal Joint

Early engines were called flat head design because they _____?

Used valves beside the cylinder

Which of the following cannot be measured using a feeler gauge?

Valve guide clearance

In typical engine lubrication systems, what components are the last to receive oil?

Valve train components

Types of communication include?

Verbal, nonverbal, written

Which tool listed is a brand name? a. Locking pliers b. Monkey wrench c. Side cutters d. Vise Grips

Vise Grips

Hazardous materials include all of the following except? a. engine oil b. asbestos c. water d. brake cleaner

Water

All of the following are usual duties of a lube technician EXCEPT ______? a. Oil change b. Air filter replacement c. Water pump replacement d. Accessory drive belt inspection

Water Pump Replacement

Which is NOT recommended during an interview? a. Wear shoes that are not sneakers b. Wear a shirt with a collar c. Have clean hair d. Wear jeans

Wear jeans

Early vehicles were constructed mostly of what material?

Wood

When taking an ASE certification test, _________

You can take a break with permission

What type of screwdriver should be used if there is very limited space above the he ad of the fastener?

offset screwdriver

The passenger side in the United States is the

Right side

The coolant flow through the radiator is controlled by the

Thermostat

What component regulated the temperature of the coolant in an engine?

Thermostat

The threaded movable part that rotates on micrometer is called the?

Thimble

The vehicle safety certification label includes all except

Tire pressure recommendation

If coolant is mixed 50-50 with water, what is the freezing point?

-34° F

An engine is operating at 2,000 RPM while the vehicle is traveling down the highway. The oil pressure should be about

20 PSI or higher

What type of lubricant is used in transfer cases

Automatic transmission fluid or a special fluid

A SOHC V-8 engine has how many camshafts

2

How many years of experience are required to achieve ASE certification?

2 years

What is the minimum tread depth required on tires in most states

2/32 in.

Most brake experts and vehicle manufacturers recommend replacing brake lining when the lining thickness is ____________________.

0.060 in. (1.5mm)

A resume should be how many pages long?

1

Credit for how many years of work experience can be substituted by attending automotive service training?

1 year

Which air impact drive size is the most commonly use?

1/2

Normal oil pump pressure in an engine is ______ PSI.

10-60

When washing hands, the water should be at what temperature?

110 F

An oil filter should be hot drained for how long before disposing of the filter?

12 hours

The vehicle identification number (VIN) since 1981, is how many characters long

17

The first self-propelled vehicle that used an OTTO cycle four-stroke gasoline engine was produced in ________?

1885

A witness mark is

A mark made when two parts touch each other and leave a mark

Horsepower is

A measurement of engine power

Dexron VI and Mercon V are examples of

Automatic Transmission Fluid (ATF)

Gasoline should be stored in approved containers that include what color?

A red container

An acceptable charging circuit voltage on a 12-volt system is ________. A) 13.5 to 15 volts B) 12 to 14 volts C) 12.6 to 15.6 volts D) 14.9 to 16.1 volts

A) 13.5 to 15 volts

When the oil pressure drops to between ____ and _____ PSI, the oil pressure lamp lights up. A) 3 and 7 B) 10 and 30 C) 30 and 50 D) 50 and 70

A) 3 and 7

How does changing the size of the tires affect the speedometer reading? A) A smaller diameter tire causes the speedometer to read faster than the actual speed and more than the actual mileage on the odometer. B) A smaller diameter tire causes the speedometer to read slower than the actual speed and more than the actual mileage on the odometer. C) A larger diameter tire causes the speedometer to read faster than the actual speed and more than the actual mileage on the odometer. D) A larger diameter tire causes the speedometer to read slower than the actual speed and more than the actual mileage on the odometer.

A) A smaller diameter tire causes the speedometer to read faster than the actual speed and more than the actual mileage on the odometer.

When measuring battery voltage, set the meter to read ___________. A) DC volts B) AC volts C) Hertz (Hz) D) Amperes (A)

A) DC volts

An electrical protection device is usually a ____________. A) Fuse B) Wire C) Electrical load device D) Switch

A) Fuse

If the voltage increases in a circuit, what happens to the current (amperes) if the resistance remains the same? A) Increases B) Decreases C) Remains the same D) Cannot be determined

A) Increases

Carbon and Silicon are examples of __________. A) Semiconductors B) Insulators C) Conductors D) Photoelectric Materials

A) Semiconductors

If two insulated wires were to melt together at the point where the copper conductors touched each other, the type of failure would be called a(n) ___________. A) Short-to-voltage B) Short-to-ground C) Open D) Floating ground

A) Short-to-voltage

A battery high-rate discharge (load capacity) test is being performed on a 12-volt battery. Technician A says that a good battery should have a voltage reading of higher than 9.6 volts while under load at the end of the 15-second test. Technician B says that the battery should be discharged (loaded) to twice its CCA rating. Which technician is correct? A) Technician A only B) Technician B only C) Both technicians B only D) Neither technician A nor B

A) Technician A only

Technician A says that metal-type tinting can affect the systems. Technician B says most navigation satellites require a monthly payment for use of the GPS navigation system. Which technician is correct? A) Technician A B) Technician B C) Both Technician A and B D) Neither Technician A nor B

A) Technician A only

Which of ASE certification test would cover experience in lighting system diagnosis?

A6

A Volkswagen Jetta is in the shop for an oil change. What specification is used for this European vehicle

ACEA

All safety glasses should meet the standards set by ______?

ANSI

When checking for stability, how high should the vehicle be raised

About 1 ft

What personal information should NOT be included on the Resume? a. Address b. Cell or telephone number c. age d. work experience

Age

What can be used to cover the jaws of a vise to help protect the object of being held?

All of the above

During and interview, try to _____ a. Show enthusiasm b. Explain your work experience c. State your willingness to work d. All the above

All the above

Which job would be concerned with the maintenance of the shop equipment? a. Service Manager b. Shop Foreman c. Shop Owner d. All the above

All the above

Housekeeping duties of a technician can include _______ a. Cleaning the floor b. Keeping the work area clean and organized c. Keeping items off the floor whenever possible d. All the above

All the above.

Professionalism includes which factor? a. Keeping your word b. Becoming a teammate with your coworkers c. Apologizing if you are wrong d. All the above

All the above.

When documenting the work order, what things should be listed? a. The test equipment used in the diagnosis b. The test procedure that was followed c. The parts that were replaced d. All the above

All the above.

Which type of system uses a one-speed transfer case and center differential with viscous coupling

All-wheel drive

The primary purpose of antilock brakes is to

Allow the front wheels to be steered during braking, allow for shorter stopping distances under all road conditions, reduce brake pad/lining wear

Which is a typical lube used in rear-drive axle assemblies? SAE 80W-90 GL-5 SAE 75W-90 GL-5 SAE 80W GL-5

Any of the above depending on the specifications of the vehicle

The proper tire inflation pressure is

As specified in the owner's manual, As shown on the door placard

Before lowering the vehicle, what should the technician do?

Be sure nothing is underneath the vehicle, raise the vehicle enough to release the safety latch, be sure no one will be walking under or near the vehicle

The part of the tire that is just under the tread of a radial tire is called the

Belt

What type of socket should be used with an air impact wrench?

Black

What part of an engine is considered to be the foundation of the engine

Block

Coolant can be checked using

Boiling/freezing points using a refractometer and hydrometer, visual inspection, and test strips

Tech a or b impact sockets?

Both

The name most often used to describe the universal joints on a conventional rear-wheel-drive vehicle driveshaft is

Cardan

What are the characters called that are imbedded in most engine blocks and are used for identification

Casting number

A hydraulic press is used to separate a bearing from the shaft. What should be used to cover the bearing ?

Brake drum

Drum brakes use what part to stop the rotation of the brake drum?

Brake shoe

What do you call the service technician's protective head cover?

Bump Cap

If 12 volts are being applied to a resistance of 3 ohms, ________ amperes will flow. A) 12 B) 2 C) 4 D) 36

C) 4

A battery should be charged at what rate? A) High or fast depending on the capacity of the charger B) At a rate of 1% of the CCA rating of the battery C) At a rate that does not cause the battery to get hotter than 125° D) Both B and C are correct

C) At a rate that does not cause the battery to get hotter than 125°

A brake warning lamp on the dash remains on whenever the ignition is on. Technician A says that there could be a fault in the hydraulic brake system. Technician B says that the problem could be due to a stuck parking brake switch. Which technician is correct? A) Technician A B) Technician B C) Both Technician A and B D) Neither Technician A nor B

C) Both Technician A and B

Technician A says that the bulb trade number is the same for all bulbs of the same size. Technician B says that a dual-filament bulb has different candlepower ratings for each filament. Which technician is correct? A) Technician A B) Technician B C) Both Technician A and B D) Neither Technician A nor B

C) Both Technician A and B

Technician A says that HID headlights give a bluish-colored light. Technician B says the high beam lights can be used as daytime running lights in some vehicles. Which technician is correct? A) Technician A B) Technician B C) Both Technician A and B D) Neither Technician A nor B

C) Both Technicians A and B

A malfunction indicator light (MIL) on the dash may be labeled?

Check engine

What type of fastener is commonly used to retain interior door panels?

Christmas tree clips

Which act or organization regulates air conditioning refrigerant?

Clean Air Act (CAA)

Windshield washer fluid is designed to

Clean the windshield, help remove bugs, contains alcohol to keep it from freezing

The Greek letter Omega (Ω) represents what unit of electricity? A) Coulomb B) Volt C) Ampere D) Ohm

D) Ohm

The __________ is a unit of electrical resistance. A) Coulomb B) Volt C) Ampere D) Ohm

D) Ohm

If running late, the wise technician should ______

Call the shop and let them know you will be late

Professional repair shops do not use ramps because

Can "kick out" and are dangerous to use

A bolt that is threaded into a casting is often called a __________?

Cap screw

Exhaust hoses should be used because one of the exhaust gases is deadly in high concentration. This gas is _______?

Carbon Monoxide or CO

Which part is clamped between the pressure plate and the flywheel

Clutch disc

The Three C's include ______

Concern, Cause, Correction

All of the following are the proper ways to dispose of a drained oil filter except? a. sent for recycling b. picked up by a service contract company c. disposed of in regular trash d. Considered to be hazardous waste and disposed of accordingly.

Considered to be hazardous waste and disposed of accordingly

A red fluid is discovered under a vehicle. This could be due to a leaking

Cooling hose (coolant leak), Transmission/ transaxle (ATF leak)

All of the following are types of clips except? a. E-clip b. Cotter c. C-Clip d. Internal

Cotter

What should be done to protect the vehicle during inspections and service?

Cover the steering wheel, protect the floor of the vehicle, protect the seats

Which metric unit of measure is used for volume measurement?

Cubic centimeter

Customer pay (CP) means

Customer pays for the repair or service Warranty does not pay for the repair or service The technician often gets paid more for each job.

What is NOT included on a work order? a. Customers Mother's maiden name b. VIN c. Mileage d. Description of work requested

Customers mother's maiden name

If 200 amperes flow from the positive terminal of a battery and operate the starter motor, how many amperes will flow back to the negative terminal of the battery? A) Cannot be determined B) Zero C) One-half (about 100 amperes) D) 200 amperes

D) 200 Amperes

A complete circuit has _________. A) A power side electrical B) An electrical load device C) A return path D) All of the above

D) All of the above

OnStar uses _________. A) GPS Information B) Digital cellular phone service C) Automatic airbag deployment notification D) All of the above

D) All of the above

What should the driver do if the TPMS warning lamp comes on steady? A) Check the inflation pressures of all tires B) Use pressure printed label on the decal near the driver's door of the specified pressure C) Some vehicles need to have the spare tire checked D) All of the above

D) All of the above

High resistance in an electrical circuit can cause ___________. A) Dim lights B) Slow motor operation C) Clicking of relays or solenoids D) All of the above

D) All the above

Which of the following are conductors? A) Gold B) Silver C) Copper D) All the above

D) All the above

What is used for daytime running lights? A) The high beam headlights at reduced intensity B) Parking lights C) Separate daytime running lights (DRL) D) Any of the above

D) Any of the Above

A dash warning light that looks like a battery means ____________. A) A fault with the battery B) A fault with the alternator C) A fault with the electrical system D) Any of the above

D) Any of the above

If the maintenance reminder light comes on, this means that the owner should ____________. A) Change oil B) Replace tires C) Replace air filter D) Any of the above

D) Any of the above

The engine will not start if _____________. A) The gear selector is in "D" B) The gear selector is in "R" C) The gear selector is in "L" D) Any of the above

D) Any of the above

Interior overhead lights (dome lights) are operated by doorjamb switches that __________. A) Complete the power side of the circuit B) Complete the ground side of the circuit C) Move the bulb(s) into contact with the power and ground D) Complete either A or B depending on application

D) Complete either A or B depending on Application

Most vehicle manufacturers specify brake fluid that meets what specification?

DOT 3

Which measuring gauge needs to set up (adjusted) to a fixed dimension before use?

Dial Bore gauge

What type of water is used in premixed coolant

Distilled water

Which type of fire extinguisher can create a corrosive compound when discharged?

Dry chemical

Automatic transmission fluid leaks can be found using a black light if

Dye is added to the fluid

To determine if a product or substance being used is hazardous, consult ________

MSDS

What type of information is commonly included in the owner's manual that would be a benefit to service technicians?

Maintenance reminder light reset procedures, tire pressure monitoring system reset procedures, maintenance items specifications

Aftermarket service information is available in what format?

Manuals, CD's or DVD's, Internet

A telescopic gauge can be used to measure a cylinder bore if what other measuring device is used to measure the telescopic gauge?

Micrometer

The proper term for channel lock is __________

Multigroove adjustable pliers

What is the purpose of a differential a. To change the direction of engine torque b. To allow the drive wheels to rotate at different speeds c. Both a and b d. Neither a nor b

Neither A nor B

Technician A says that the diameter of a bolt is the same as the wrench size used to remove or install the fastener. Technician B says that the length is measured from the top of the head of the bolt to the end of the bolt. Which technician is correct?

Neither A or B

The driving gear has 15 teeth and the driven gear has 29 teeth. Technician A says that the output gear will be going faster than the input gear. Technician B says the ratio is 3.86:1. Which technician is correct?

Neither technician A nor B

The "add" mark on an automatic transmission dipstick means

One-half quart (half liter)

If a thermostat is not working, what diagnostic trouble code could be set?

P0128

When using a fire extinguisher, what word can be used to remember what to do?

PASS

Using the modified X tire rotation method on a front-wheel-drive vehicle, where would be the place for the right front tire

Right rear

which type of manual or service information includes the flat-rate time and the cost parts

Parts and times guides

Pad extensions may be needed when hoisting what type of vehicle?

Pickup trucks, Vans

The steering gear rotates which part on a system using a conventional type steering gear

Pitman arm

A typical automatic transmission includes

Planetary gear sets, clutches or bands, torque converter

Torque is expressed in units of ________.

Pound-feet

A drive shaft is also called a

Propellor shaft or Prop shaft

When inspecting engine oil what should be checked

Proper level, color, feels slippery and not gritty

When working with hand tools, always ___________

Pull a wrench-- don't push it

What automotive devices may contain mercury?

Rear seat video displays Navigation displays HID headlights

What color is new automatic transmission fluid (ATF)

Red

Power-assisted brakes are used to

Reduce the force required by the driver on brake pedal

Two technicians are discussing the safe use of a wrench. Technician A says that a wrench should be pulled towards you. Technician B says that a wrench should be pushed away from you. Which technician is correct?

Tech A only

Two technicians are discussing the duties of a shop foreman and a service manager. Technician A says that a shop foreman diagnoses vehicle problems. Technician B says that the service manager usually repairs vehicles. Which technician is correct?

Tech A only.

Technician A says that the net pay amount is usually higher than the gross pay amount. Technician B says that the gross pay amount is usually higher than the net pay. Which technician is correct?

Tech B only

Two technicians are discussing torque wrenches. Technician A says that a torque wrench is capable of tightening a fastener with more torque than a conventional breaker bar or ratchet. Technician B says that a torque wrench should be calibrate regularly for the most accurate results. Which technician is correct?

Tech B only

A "chirping" or squealing noise is heard while the vehicle is moving forward, but stops when the brakes are applied. Technician A says that the noise is likely caused by the disc brake pad wear sensors. Technician B says the noise is likely a wheel bearing because the noise stops when the brakes are applied. Which technician is correct?

Technician A

Technician A says that a crankshaft determines the stroke of an engine. Technician B says that the length of the connecting rod determines the stroke of an engine. Which technician is correct?

Technician A

Technician A says that a creeper should be stored verti-cally. Technician B says that a creeper should be stored on its casters. Which technician is correct?

Technician A

Technician A says that a hoist can be stopped at any level as long as the safety latch engages. Technician B says that the vehicle should be hoisted to the top of the hoist travel for safety. Which technician is correct?

Technician A

Technician A says that the power brake system (boost system) helps reduce the force required by the driver to apply the brakes. Technician B says the brake boost system is used to reduce stopping distance. Which technician is correct?

Technician A

Technician A says that the vehicle should not be driven on public streets or highways if the red brake warning light is on. Technician B says that the vehicle should not be driven on public streets or highways if the amber antilock brake warning light is on. Which technician is correct?

Technician A

Which type of question is the same as two true-and-false questions?

Technician A and Technician B

A service technician removed the inspection/fill plug from the differential of a rear-wheel-drive vehicle and gear lube started to flow out. Technician A says to quickly replace the plug to prevent any more loss of gear lube. Technician B says to catch the fluid and allow the fluid to continue to drain. Which technician is correct?

Technician B

Technician A says that the tinnerman nuts are used to hold the brake drum on and should be reinstalled when the drum is replaced. Technician B says that before the brake drum is removed, the brakes should be wetted to prevent possible asbestos dust from being released into the air. Which technician is correct?

Technician B

In a rack-and-pinion steering gear, which part is the rack?

The part that is moved side to side when the steering wheel is turned

Flat-rate pay means

The technician is paid according to the job, not by the number of hours worked.

Which is a type of spring a. Coil b. Leaf c. Torsion bar d. all of the above

all of the above

New Vehicle Preparation is usually an entry-level vehicle service position and usually involves what duties? a. Installing dealer installed options b. Correcting tire pressures c. removal of all protective coverings and plastic d. all the above

all the above

The freezing point of water is?

both 0 degrees and 32 degrees

Proper care of shop equipment includes

both b and c

Disc brakes are used

both front and rear

What type of hammer is plastic coated, has a metal casing and is filled with small lead balls?

dead blow hammer

Accessory drive belts should be checked for proper tension by

deflection, tensioner marks, a torque wrench reading on the tensioner

Used engine oil should be disposed of by all EXCEPT the following methods? a. disposed of in regular trash b. shipped offsite for recycling c. burned onsite in a waste-oil-approved heater d. burned offsite in a waste-oil-approved heater

disposed of in a regular trash

DEX-COOL is what type of coolant?

ethylene glycol

Oil passages in an engine block are usually called

galleries

A coolant leak will show as what color

green, red, orange, depending on the type of coolant

Which part is splined to the clutch disc?

input shaft

The aspect ratio of a tire means

ratio of height to width

The grade of a fastener, such as a bolt, is a measure of its ____________?

tensile strength

Where is the "peen" of the hammer

the back part opposite of the striking face

A rotating force is called

torque

which tool has a replacement cutting edge?

utility knife.

Coolant is antifreeze plus

water


Set pelajaran terkait

Industrial Revolution Definition Terms

View Set

BA 220 FINAL STUDY GUIDE PEPPERDINE

View Set

Introduction - who can vote and who cannot

View Set

Biology Chapter 7 - Cell Organelles "Help Wanted Ads"

View Set

Geometry B, Assignment 6. Area of Regular Polygons

View Set