OSPF 1-2

Match the OSPF state with the order in which it occurs. (Not all options are used.) 1st state

Down

Match the OSPF state with the order in which it occurs. (Not all options are used.) 2nd state

Init

In an OSPFv2 configuration, what is the effect of entering the command network 192.168.1.1 0.0.0.0 area 0 ?

It tells the router which interface to turn on for the OSPF routing process.

Which OPSF packet contains the different types of link-state advertisements?

LSU

Match the OSPF state with the order in which it occurs. (Not all options are used.) 6th state

Loading

Match the description to the term. (Not all options are used.) link-state database

This is where you can find the topology table.

What is a benefit of multiarea OSPF routing?

Topology changes in one area do not cause SPF recalculations in other areas.

What type of address is 64.101.198.197?

public

Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?

show ip ospf interface serial 0/0/0

What is used to facilitate hierarchical routing in OSPF?

the use of multiple areas

In an OSPF network when are DR and BDR elections required?

when the routers are interconnected over a common Ethernet network

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 64.102.0.0 255.255.255.128. What wildcard mask would the administrator use in the OSPF network statement?

0.0.0.127

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 64.100.0.0 255.255.255.0. What wildcard mask would the administrator use in the OSPF network statement?

0.0.0.255

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 128.107.0.0 255.255.255.192. What wildcard mask would the administrator use in the OSPF network statement?

0.0.0.63

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 192.168.181.0 255.255.254.0. What wildcard mask would the administrator use in the OSPF network statement?

0.0.1.255

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 192.168.223.0 255.255.254.0. What wildcard mask would the administrator use in the OSPF network statement?

0.0.1.255

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 128.107.0.0 255.255.252.0. What wildcard mask would the administrator use in the OSPF network statement?

0.0.3.255

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 198.19.0.0 255.255.252.0. What wildcard mask would the administrator use in the OSPF network statement?

0.0.3.255

By default, what is the OSPF cost for any link with a bandwidth of 100 Mb/s or greater?

1

What is the default router priority value for all Cisco OSPF routers?

1

Match the description to the term. (Not all options are used.) single-area OSPF

All the routers are in the backbone area.

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. Which task has to be performed on Router 1 for it to establish an OSPF adjacency with Router 2?

Change the subnet mask of interface FastEthernet 0/0 to 255.255.255.0.

What is the recommended Cisco best practice for configuring an OSPF-enabled router so that each router can be easily identified when troubleshooting routing issues?

Configure a value using the router-id command.

DUAL is the algorithm used by ________. In multiarea OSPF, OSPF is implemented using multiple areas, and all of them must be connected to the backbone area.

EIGRP

Match the OSPF state with the order in which it occurs. (Not all options are used.) 5th state

Exchange

Match the OSPF state with the order in which it occurs. (Not all options are used.) 4th state

Exstart

Match the OSPF state with the order in which it occurs. (Not all options are used.) 7th state

Full

After modifying the router ID on an OSPF router, what is the preferred method to make the new router ID effective?

HQ# clear ip ospf process

Which three OSPF states are involved when two routers are forming an adjacency? (Choose three.)

Init Two-way Down

Which three statements describe features of the OSPF topology table? (Choose three.)

It is a link-state database that represents the network topology. When converged, all routers in an area have identical topology tables. The table can be viewed via the show ip ospf database command.

Interface Fa0/0 has not been activated for OSPFv2 on router R2.

Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers but PC1 is unable to connect to PC2. What is the most likely problem?

The R1 dead timer expires between hello packets from R2.

Refer to the exhibit. A network administrator has configured the OSPF timers to the values that are shown in the graphic. What is the result of having those manually configured timers?

192.168.1.100

Refer to the exhibit. If no router ID was manually configured, what would router Branch1 use as its OSPF router ID?

Router R4 will become the DR and router R1 will become the BDR.

Refer to the exhibit. If the switch reboots and all routers have to re-establish OSPF adjacencies, which routers will become the new DR and BDR?

R0-A

Refer to the exhibit. On which router or routers would a default route be statically configured in a corporate environment that uses single area OSPF as the routing protocol?

If the DR fails, the new DR will be router B.

Refer to the exhibit. Suppose that routers B, C, and D have a default priority, and router A has a priority 0. Which conclusion can be drawn from the DR/BDR election process?​

65

Refer to the exhibit. What is the OSPF cost to reach the router A LAN 172.16.1.0/24 from B?

R1# show ip ospf interface serial0/0/1

Refer to the exhibit. Which command did an administrator issue to produce this output?

R3 will be elected BDR. The R4 router ID is 172.16.1.1. R2 will be elected DR.

Refer to the exhibit. Which three statements describe the results of the OSPF election process of the topology that is shown in the exhibit? (Choose three.)

A network engineer has manually configured the hello interval to 15 seconds on an interface of a router that is running OSPFv2. By default, how will the dead interval on the interface be affected?

The dead interval will now be 60 seconds.

Match the description to the term. (Not all options are used.) Shortest Path First

This is the algorithm used by OSPF.

Match the description to the term. (Not all options are used.) adjacency database

This is where the details of neighboring routers can be found.

Match the OSPF state with the order in which it occurs. (Not all options are used.) 3rd state

Two-way

What is the format of the router ID on an OSPF-enabled router?

a 32-bit number formatted like an IPv4 address

Match each OSPF packet type to how it is used by a router. (Not all options are used.) link-state update packet

advertise new information

What will an OSPF router prefer to use first as a router ID?

any IP address that is configured using the router-id command

Which step in the link-state routing process is described by a router building a link-state database based on received LSAs?

building the topology table

Which step in the link-state routing process is described by a router inserting best paths into the routing table?

choosing the best route

Match each OSPF packet type to how it is used by a router. (Not all options are used.) database description packet

compare local topology to be sent by another router

Which type of OSPFv2 packet contains an abbreviated list of the LSDB of a sending router and is used by receiving routers to check against the local LSDB?

database description

To establish a neighbor adjacency two OSPF routers will exchange hello packets. Which two values in the hello packets must match on both routers? (Choose two.)

dead interval hello interval

Match each OSPF packet type to how it is used by a router. (Not all options are used.) Hello packet

establish & maintain adjacency

Which step in the link-state routing process is described by a router sending Hello packets out all of the OSPF-enabled interfaces?

establishing neighbor adjacencies

When an OSPF network is converged and no network topology change has been detected by a router, how often will LSU packets be sent to neighboring routers?

every 30 minutes

Which step does an OSPF-enabled router take immediately after establishing an adjacency with another router?

exchanges link-state advertisements

Which step in the link-state routing process is described by a router flooding link-state and cost information about each directly connected link?

exchanging link-state advertisements

Which step in the link-state routing process is described by a router running an algorithm to determine the best path to each destination?

executing the SPF algorithm

What indicates to a link-state router that a neighbor is unreachable?

if the router no longer receives hello packets

Which OSPF data structure is identical on all OSPF routers that share the same area?

link-state database

Match each OSPF packet type to how it is used by a router. (Not all options are used.) link-state request packet

query another router for additional information

An OSPF router has three directly connected networks; 172.16.0.0/16, 172.16.1.0/16, and 172.16.2.0/16. Which OSPF network command would advertise only the 172.16.1.0 network to neighbors?

router(config-router)# network 172.16.1.0 255.255.255.0 area 0

What does an OSPF area contain?

routers that have the same link-state information in their LSDBs

What command would be used to determine if a routing protocol-initiated relationship had been made with an adjacent router?

show ip ospf neighbor

Which command is used to verify that OSPF is enabled and also provides a list of the networks that are being advertised by the network?​

show ip protocols

A network technician issues the following commands when configuring a router: R1(config)# router ospf 11 R1(config-router)# network 10.10.10.0 0.0.0.255 area 0 What does the number 11 represent?

the OSPF process ID on R1

What is a function of OSPF hello packets?

to discover neighbors and build adjacencies between them

What is the reason for a network engineer to alter the default reference bandwidth parameter when configuring OSPF?

to more accurately reflect the cost of links greater than 100 Mb/s

What are the two purposes of an OSPF router ID? (Choose two.)

to uniquely identify the router within the OSPF domain to facilitate router participation in the election of the designated router