router chapter 16 quiz
What type of route adds the subnet to the routing table of a Cisco device when the ip address command is issued on an interface with a state of Up/Up? Interface route Static route Connected route Local route
Local route
What is the name of the oldest variation of Cisco internal routing logic? Cisco Express Forwarding Quick switching Process switching Fast switching
Process switching
The ________ configuration creates a subinterface for each VLAN on the trunk and routes all frames associated with each VLAN ID as it comes in or out of the subinterface. MLS CEF ROAS Fast switching
ROAS
You need to configure a default route. Which of the following commands is the correct way to set the default route out of your network? ip route 0.0.0.0 172.20.3.2 ip route 0.0.0.0.0.0.0.0 172.20.3.2 ip route 0.0.0.0 0.0.0.0 172.20.3.2 ip route any 172.20.3.2
ip route 0.0.0.0 0.0.0.0 172.20.3.2
Which Cisco IOS command is used to disable the use of the zero subnet? no ip classless no ip subnet-zero no subnet-zero ip classless
no ip subnet-zero
What parameter can be added to the end of a Cisco IOS ip route command to force its inclusion into the routing table, regardless of interface/next-hop status? permanent Configure the AD to 0 full Configure the AD to 1
permanent
Which Cisco IOS show command is used to display the VLAN configuration (including native VLAN configuration) of a router? show ip roas show vlan show interfaces show vlans
show vlans
When configuring a trunk between a router and a switch, which command must be configured on the switch to ensure that the trunk comes up? (Choose all that apply.) switchport mode access switchport mode dynamic auto switchport mode dynamic desirable switchport mode trunk
switchport mode trunk
On modern Cisco routers, what is the default version of internal routing logic used? Fast switching Cisco Express Forwarding Process switching Quick switching
Cisco Express Forwarding
What type of route adds the host to the routing table of a Cisco device when the ip address command is issued on an interface with a state of Up/Up? Static route Interface route Local route Connected route
Connected route
What is the process of removing the Layer 2 header and trailer information to reveal the Layer 3 packet? Deencapsulation Encapsulation Encryption Decryption
Deencapsulation
What VLAN(s) should devices in the IP subnet be in? Devices in a single VLAN should be in the same IP subnet. Devices in different VLANs should be in separate IP subnets. Devices in different VLANs should be in the same subnet if needed. IP subnet and VLAN placement does not really matter. Devices in a single VLAN should be in separate IP subnets.
Devices in a single VLAN should be in the same IP subnet. Devices in different VLANs should be in separate IP subnets.
As the network engineer, you are configuring the Fast Ethernet interface. You have issued the following command to the fa0/0 interface: ip address 200.16.24.1 255.255.255.0. Which of the following must be true before the router can add this information to its routing table? The interface must have the no shutdown command issued. The interface must be administratively turned off. The router must be able to communicate with its neighbor first. The interface status codes for the interface must be in the up and up condition.
The interface status codes for the interface must be in the up and up condition. The interface must have the no shutdown command issued.
In what two conditions does a router choose to process a frame? (Choose two.)
When the frame destination address is the same as the local address (Layer 2) When the frame has no errors
Which Cisco IOS command is used on a router that is being configured with a ROAS configuration to manage traffic from a specific VLAN? dot1q vlan-id dot1q vlan vlan-id encapsulation dot1q vlan-id encapsulation 802.1q vlan-id
encapsulation dot1q vlan-id
Which Cisco IOS command is used on a router that is being configured with a ROAS configuration to manage untagged traffic? dot1q vlan-id native encapsulation 802.1q vlan-id native dot1q native vlan vlan-id encapsulation dot1q vlan-id native
encapsulation dot1q vlan-id native
