Vehicle Management Craftsman

4. (203) How many steering clutch packs are used in the Fiat Allis crawler tractor? a. 2. b. 4. c. 6. d. 8.

a. 2.

43. (009) What publication does the 441st Vehicle Support Chain Operations Squadron (VSCOS) use to manage war reserve materiel (WRM) vehicle assets? a. Air Force Instruction (AFI) 25-101. b. Air Force Manpower Standard (AFMS) 52B1. c. Air Force Computer System Manual (AFCSM) 24-1. d. Technical Order (TO) 36A-1-1301.

a. Air Force Instruction (AFI) 25-101.

61. (013) What is the significant difference between the M1116 high-mobility, multipurpose wheeled vehicle (HMMWV) as compared to the other HMMWV models? a. Armored body. b. Winterization kit. c. Time delay module. d. Front and rear winch.

a. Armored body.

81. (016) On the MaxxPro Mine-Resistant, Ambush-Protected (MRAP) vehicle, which armor component is made of ceramic composite? a. Base cab. b. Spall liners. c. Catcher plates. d. Effector assemblies.

a. Base cab.

7. (204) What prevents movement of the steering clutch outer drum on the Fiat Allis crawler tractor during a turn? a. Brake band. b. Accumulator. c. Slave cylinder. d. Hydraulic piston.

a. Brake band.

34. (007) What two areas does on-the-job training (OJT) consist of? a. Career knowledge and task performance. b. Career knowledge and personal knowledge. c. Task knowledge and task performance. d. Task performance and personal knowledge.

a. Career knowledge and task performance.

68. (013) What provides a ground circuit to the alternator for the high-mobility, multipurpose wheeled vehicle (HMMWV) generating system? a. Circuit 3. b. Circuit 5. c. Circuit 29. d. Circuit 568.

a. Circuit 3.

75. (015) Which component on the 5-ton M-series front winch engages the winch drum gear to the drive gear of the winch motor? a. Clutch lever. b. Hydraulic control valve. c. Winch control switch. d. Power take-off (PTO) control switch.

a. Clutch lever.

60. (012) What vehicles are not included when conducting vehicle rotation analysis? a. General Services Administration (GSA) and other leased vehicles. b. Only vehicles with high mileage. c. Only vehicles with low mileage. d. Non-registered equipment.

a. General Services Administration (GSA) and other leased vehicles.

63. (013) What high-mobility, multipurpose wheeled vehicle (HMMWV) drive train components transfer torque to the wheels from the differential through the geared hubs? a. Halfshafts. b. Transfer cases. c. Propeller shafts. d. Recirculating ball gearboxes.

a. Halfshafts.

88. (017) On the MaxxPro Mine-Resistant, Ambush-Protected (MRAP) vehicle, what should the engine speed be during the VENT mode check while performing the life support and heating, ventilation, and air conditioning (HVAC) systems' function check? a. Idle. b. 1,300 revolutions per mile (rpm). c. 1,700 rpm. d. 2,100 rpm.

a. Idle.

8. (204) Which holds the track chain together on the Fiat Allis crawler tractor? a. Machined pins. b. Case-hardened pins. c. Case-hardened rivets. d. Machined bolts with lock plates.

a. Machined pins.

19. (004) Which is a positive manpower variance? a. Missile mobile maintenance support. b. Material control function realigned. c. Number of vehicles assigned. d. Vehicle complexity.

a. Missile mobile maintenance support.

71. (014) How do you unlock the throttle control setting on a 2½-ton M-series? a. Rotate handle clockwise or counterclockwise. b. Rotate handle clockwise only. c. Step on the accelerator pedal. d. Step on the brake pedal.

a. Rotate handle clockwise or counterclockwise.

66. (013) What type of headlight switch do most M-series vehicle lighting systems use? a. Three-lever. b. Two-lever. c. Automatic. d. Rheostat.

a. Three-lever.

54. (011) Which report is used to keep track of work orders in the Defense Property Accountability System (DPAS)? a. Work order master inquiry. b. Mission capable report. c. Vehicle master inquiry. d. Vehicle in commission report.

a. Work order master inquiry.

39. (008) The Air Force (AF) Form 616, Fund Cite Authorization (FCA), is provided to the accounting liaison office (ALO) to report the projected estimate of Department of Defense (DOD) fleet credit card non-fuel purchases a. quarterly. b. by 1 January of each year. c. by 1 October of each year. d. only upon receipt of a new vehicle.

a. quarterly.

47. (009) An immediate, temporary repair of a battle-damaged vehicle during post-attack recovery operations is called a. triage maintenance. b. quick-reaction maintenance. c. organizational maintenance. d. post-attack vehicle operability (PAVO).

a. triage maintenance.

17. (004) Factors that affect manpower authorizations are called a. variances. b. standards. c. change factors. d. tenant agreements.

a. variances.

87. (017) On the MaxxPro Mine-Resistant, Ambush-Protected (MRAP) vehicle, what should the engine speed be during the COOL mode check while performing the life support and heating, ventilation, and air conditioning (HVAC) systems' function check? a. Idle. b. 1,300 revolutions per minute (rpm). c. 1,700 rpm. d. 2,100 rpm.

b. 1,300 revolutions per minute (rpm).

70. (014) The air system on the 2½-ton M-series contains how many rear couplings? a. 1. b. 2. c. 3. d. 4.

b. 2.

78. (016) The MaxxPro Mine-Resistant, Ambush-Protected (MRAP) vehicle can carry up to how many personnel? a. 4. b. 6. c. 8. d. 10.

b. 6

32. (007) Within how many days after a trainee is assigned to a work center would a supervisor's initial journal entry be documented in the training business area (TBA)? a. 30. b. 60. c. 90. d. 120.

b. 60.

10. (003) How many years are added to the life expectancy of a depot-overhauled vehicle? a. 5. b. 7. c. 10. d. 12.

b. 7.

16. (004) What is a vehicle equivalent (VE)? a. An alphanumeric code assigned to multi-role vehicles. b. A numeric value assigned to a vehicle, based on its maintenance complexity. c. An alphanumeric designator assigned to a vehicle, based on its mission role. d. A numeric code assigned to a vehicle designating that it has multi-role capabilities.

b. A numeric value assigned to a vehicle, based on its maintenance complexity.

56. (012) Request for vehicle authorization changes are submitted on an a. Air Force (AF) Form 2005, Issue/Turn-in Request. b. AF Form 601, Equipment Action Request. c. Department of Defense (DD) Form 1149, Requisition and Invoice/Shipping Document. d. DD Form 1348-1, DOD Single Line Item Requisition System Document.

b. AF Form 601, Equipment Action Request.

27. (006) Which publication is used to identify shop-specific equipment by type and quantity? a. Allowance Source Code (ASC) 403. b. ASC 457. c. Technical Order (TO) 36-1-50, Motor Vehicle Maintenance Guide. d. TO 36-1-191, Technical and Managerial Reference for Motor Vehicle Maintenance.

b. ASC 457.

24. (005) What document is used when outfitting a vehicle maintenance (VM) shop with equipment? a. Air Force Equipment Management System (AFEMS). b. Allowance Source Code (ASC) 457. c. ASC 403. d. Mission critical list.

b. Allowance Source Code (ASC) 457.

83. (016) On the MaxxPro Mine-Resistant, Ambush-Protected (MRAP) vehicle, which armor component attaches to brackets and is held several inches from the vehicle body? a. Base cab. b. Spall liners. c. Catcher plates. b. Effector assemblies.

b. Effector assemblies.

69. (014) How many forward and reverse gears are available when using the transmission in conjunction with the transfer case on the 2½-ton M-series? a. Eight forward and one reverse. b. Eight forward and two reverse. c. Six forward and one reverse. d. Six forward and two reverse.

b. Eight forward and two reverse.

6. (002) When assigning work orders in accordance with priorities, which condition does not automatically cause a vehicle to have a higher priority than other vehicles? a. A special project requires a certain type of vehicle in service. b. Emergency warning lights, military radios, and other such accessories. c. Severe weather or other natural circumstances create a need for certain types of vehicles. d. A unit is below the minimum essential vehicle level and other base assets cannot fulfill the unit's need.

b. Emergency warning lights, military radios, and other such accessories.

80. (016) Which area(s), protected by the fire suppression system (FSS) on the MaxxPro MineResistant, Ambush-Protected (MRAP) vehicle, can only be operated manually? a. Tires only. b. Fuel tank and tires. c. Engine and interior. d. Interior, engine, fuel tank, and tires.

b. Fuel tank and tires.

65. (013) What high-mobility, multipurpose wheeled vehicle (HMMWV) suspension system component provides a gear reduction to increase torque to the wheel and tire assembly? a. Ball joint. b. Geared hub. c. Shock absorber. d. Upper control arm.

b. Geared hub.

74. (015) What provides operating power for the auxiliary equipment on the 5-ton M-series truck? a. Engine. b. Hydraulics. c. Electronics. d. Transmission.

b. Hydraulics.

92. (018) What level of triage maintenance requires more than 30 minutes of repair work but less than four hours? a. Level A. b. Level B. c. Level C. d. Level D.

b. Level B.

12. (003) What guidance specifies the extent of completed work and types of repairs that receive quality assurance (QA) inspections? a. Major command (MAJCOM) policy. b. Local operating instruction (OI). c. AFI 23-302, Vehicle Management. d. TO 36-1-191, Technical and Managerial Reference for Motor Vehicle Maintenance.

b. Local operating instruction (OI).

45. (009) Who develops specific storage concepts for vehicles identified against operation plan (OPLAN) tasking? a. Group commander. b. Major command (MAJCOM). c. Vehicle fleet manager (VFM). d. Logistics readiness squadron (LRS) commander.

b. Major command (MAJCOM).

20. (004) Which is a negative manpower variance? a. Missile mobile maintenance support. b. Material control function realigned. c. Number of vehicles assigned. d. Vehicle complexity.

b. Material control function realigned.

5. (002) To whom is the mission-essential level (MEL) presented for final approval? a. Logistics readiness squadron (LRS) commander. b. Mission support group (MSG) commander. c. Major command (MAJCOM) commander. d. Wing commander.

b. Mission support group (MSG) commander.

49. (009) During wartime, which factor would most likely drive a lower standard of serviceability in vehicle management (VM) compared to peacetime operations? a. Damage assessments. b. Spare parts availability. c. Skill level of personnel. d. Operational speed of the vehicle.

b. Spare parts availability.

23. (005) How many categories of property are in the supply system? a. One. b. Two. c. Three. d. Four.

b. Two.

33. (007) Who does the training monitor work with to develop a rotational training plan? a. Vehicle fleet manager (VFM)/vehicle management superintendent (VMS) only. b. VFM/VMS and work center supervisors. c. Work center supervisor only. d. Commander.

b. VFM/VMS and work center supervisors.

1. (005) What is the code used to identify repairable cycle assets that are primarily under depot-level control? a. ND. b. XD. c. NC. d. XB.

b. XD.

59. (012) Before making a decision on underutilized vehicles, you must consider a. turning the unit into salvage. b. deleting the authorization. c. driving the unit to add mileage. d. failing the vehicle during the assessment inspection.

b. deleting the authorization.

7. (002) The section supervisor is responsible for a. picking up work orders from Fleet Management and Analysis (FM&A), and setting the priority and order of work requirements. b. disseminating the workload to the shop. c. notifying FM&A of the requirement for more work and setting the work priority. d. prioritizing work and providing FM&A with factual estimated completion times.

b. disseminating the workload to the shop.

86. (017) On the MaxxPro Mine-Resistant, Ambush-Protected (MRAP) vehicle, you connect an air conditioning (AC) recovery/recharging unit to the vehicle while performing a COOL mode check during the life support and heating, ventilation, and air conditioning (HVAC) systems' function check to a. recover refrigerant. b. monitor pressures. c. control pressures. d. add refrigerant.

b. monitor pressures.

2. (202) The main hydraulic pump on the Arva crane is a a. single gear-type pump. b. tandem gear-type pump. c. single gerotor-type pump. d. tandem gerotor-type pump.

b. tandem gear-type pump.

90. (017) How much do the armor plates on the sides of the MaxxPro Mine-Resistant, Ambush Protected (MRAP) vehicle's engine weigh? a. 65-80 pounds each. b. 80-100 pounds each. c. 100-120 pounds each. d. 120-150 pounds each.

c. 100-120 pounds each.

1. (201) How many forward and reverse gears does the Arva crane have? a. 2 forward and 2 reverse. b. 3 forward and 1 reverse. c. 3 forward and 3 reverse. d. 4 forward and 1 reverse.

c. 3 forward and 3 reverse.

62. (013) At what angle is the radiator mounted in a high-mobility, multipurpose wheeled vehicle (HMMWV)? a. 35 degrees. b. 40 degrees. c. 45 degrees. d. 50 degrees.

c. 45 degrees.

67. (013) How many blackout light positions are on the high-mobility, multipurpose wheeled vehicle (HMMWV)? a. 1. b. 3. c. 5. d. 7.

c. 5.

11. (003) What is the warranty period for all depot-overhauled vehicles? a. 12 months, 12,000 miles. b. 15 months, 12,000 miles. c. According to specific contract specifications. d. According to commercial manufacturer warranties.

c. According to specific contract specifications.

30. (007) When would you review master training plans (MTP) and individual training plans (ITP)? a. Monthly or when any changes are made to the career field education and training plan(CFETP). b. Quarterly or when any changes are made to the CFETP. c. Annually or when any changes are made to the CFETP. d. Bi-annually or when any changes are made to the CFETP.

c. Annually or when any changes are made to the CFETP.

21. (005) What is one of the contributions you can make to supply discipline? a. Use the fraud, waste, and abuse (FWA) program. b. Double order parts to prepare for the next job. c. Avoid requesting more than is needed. d. Maintain on-hand bench stocks.

c. Avoid requesting more than is needed.

82. (016) On the MaxxPro Mine-Resistant, Ambush-Protected (MRAP) vehicle, which armor component attaches externally to the base armor? a. Base cab. b. Spall liners. c. Catcher plates. d. Effector assemblies.

c. Catcher plates.

37. (008) Which organization provides policy oversight for the Department of Defense (DOD) fleet credit card? a. Base fuels flight. b. Defense fuels center. c. Defense Energy Support Center (DESC). d. General Services Administration (GSA).

c. Defense Energy Support Center (DESC).

42. (009) Which statement best describes a vehicle maintenance (VM) function in support of the United States Air Force War and Mobilization Plan (WMP)? a. Provide manning and training. b. Develop mobility and contingency plans. c. Determine suitable vehicles for deployment. d. Develop the logistics readiness squadron (LRS) annex to the base mobility plan.

c. Determine suitable vehicles for deployment.

79. (016) Which areas, protected by the fire suppression system (FSS) on the MaxxPro MineResistant, Ambush-Protected (MRAP) vehicle, operate automatically? a. Tires only. b. Fuel tank and tires. c. Engine and interior fire sensors. d. Interior, engine, fuel tank and tires.

c. Engine and interior fire sensors.

2. (001) Who is the focal point for coordinating and generating all work through your shop? a. Customer Service Center (CSC). b. The work center supervisor. c. Fleet Management and Analysis (FM&A). d. Vehicle fleet manager or vehicle management superintendent (VFM/VMS).

c. Fleet Management and Analysis (FM&A).

64. (013) What high-mobility, multipurpose wheeled vehicle (HMMWV) drive train components act as the final drive components to front and rear wheels? a. Halfshafts. b. Differentials. c. Geared hubs. d. Propeller shafts.

c. Geared hubs.

44. (009) Who has overall base level responsibility to ensure the readiness of assigned war reserve materiel (WRM)? a. Logistics readiness squadron (LRS) commander. b. Vehicle fleet manager (VFM). c. Installation commander. d. Group commander.

c. Installation commander.

73. (015) What major component of the 5-ton M-series permits towing by another vehicle? a. Pintle hook. b. Tie down hooks. c. Lifting shackles. d. Tie-down shackles.

c. Lifting shackles.

84. (017) On the MaxxPro Mine-Resistant, Ambush-Protected (MRAP) vehicle, to place the electronic gauge cluster (EGC) in diagnostic mode, turn the ignition switch to ON or ACCESSORY and then press the cruise control a. ON switch followed by RESUME switch. b. ON switch followed by CANCEL switch. c. ON and RESUME switches simultaneously. d. RESUME and CANCEL switches simultaneously.

c. ON and RESUME switches simultaneously.

51. (010) Where do you file the completed time compliance technical orders (TCTO)? a. Technical order (TO) monitor files in TO library. b. Materiel Control completed parts file. c. Permanent side of the vehicle record jacket. d. Temporary side of the vehicle record jacket.

c. Permanent side of the vehicle record jacket.

31. (007) How often should the vehicle management (VM) training monitor review individual training plans (ITP) on upgrade trainees? a. Daily. b. Monthly. c. Quarterly. d. Annually.

c. Quarterly.

77. (015) What major component for raising and lowering the wrecker crane cable and hook guides the hoist cable through the boom? a. Pads. b. Rollers. c. Sheaves. d. Sprockets.

c. Sheaves.

14. (004) Which phrase best describes manpower? a. The total number of positions assigned to an organization. b. The total number of personnel assigned to an organization. c. The total number of jobs or positions required to accomplish a particular mission. d. The military personnel that fill the positions required to accomplish a particular mission.

c. The total number of jobs or positions required to accomplish a particular mission.

76. (015) What major component of the 5-ton M-series medium wrecker is used to control the operating gear ratio of the rear winch drive motor? a. Control linkage. b. Torque control valve. c. Torque control lever. d. Directional control valve.

c. Torque control lever.

36. (008) Who is responsible for controlling the vehicle management budget? a. Materiel Control. b. Base comptroller. c. Vehicle fleet manager (VFM). d. Vehicle management and analysis (VM&A).

c. Vehicle fleet manager (VFM).

53. (011) Which report contains data for all the registered and non-registered vehicles for which vehicle management (VM) has primary responsibility? a. Daily status report. b. Automated analysis report. c. Vehicle master inquiry. d. Vehicle management report.

c. Vehicle master inquiry.

38. (008) The Department of Defense (DOD) fleet credit card is reissued to customers in a new control register a. quarterly. b. by 1 January of each year. c. by 1 October of each year. d. only upon receipt of a new vehicle.

c. by 1 October of each year.

28. (006) The Vendor Product Evaluation Program is designed to a. test after-market performance equipment that may be useful to the Air Force (AF). b. conduct field evaluations on commercial products to verify the manufacturer's performance claims. c. enhance operations by identifying more effective and economical equipment through field evaluations. d. evaluate equipment that is new to the AF inventory and identify its economic effectiveness.

c. enhance operations by identifying more effective and economical equipment through field evaluations.

22. (005) The financial obligation to pay for the loss, damage, or destruction of a vehicle resulting from abuse is known as a. report of survey. b. supply discipline. c. pecuniary liability. d. property accountability.

c. pecuniary liability.

57. (012) The master vehicle report (MVR) breaks down vehicle authorizations by a. serial number. b. stock record account number. c. prime national stock number (NSN). d. interchangeability and substitutability NSN.

c. prime national stock number (NSN).

13. (003) Areas that you should consider prior to assigning an individual to perform quality assurance (QA) inspections are a. skill level, rank, and Air Force specialty code (AFSC). b. skill level, rank, and experience. c. skill level, broad expertise, and ability to avoid favoritism or bias. d. prior inspection experience, rank, and ability to maintain process integrity.

c. skill level, broad expertise, and ability to avoid favoritism or bias.

50. (010) Who may direct removal of a vehicle from service until an "outstanding" time compliance technical order (TCTO) has been accomplished? a. Vehicle fleet manager (VFM). b. Fleet Management and Analysis (FM&A). c. Robins Air Force Base (AFB) Special Equipment and Vehicles (SE&V). d. 441st Vehicle Support Chain Operations Squadron (VSCOS).

d. 441st Vehicle Support Chain Operations Squadron (VSCOS).

55. (012) Major commands (MAJCOM) must not exceed established vehicle ceilings without prior approval from a. Congress. b. Headquarters (HQ) Standard Systems Group (SSG). c. Robins Air Force Base (AFB) Special Equipment and Vehicles (SE&V). d. 441st Vehicle Support Chain Operations Squadron (VSCOS).

d. 441st Vehicle Support Chain Operations Squadron (VSCOS).

3. (202) A warning light will flash accompanied by an audible warning when the load on the Arva crane's hook is at or above a. 70 percent. b. 75 percent. c. 80 percent. d. 85 percent.

d. 85 percent.

8. (003) What document accompanies a vehicle to the depot repair facility? a. Original limited technical inspection (LTI). b. Vehicle repair history (AF Form 1828). c. Shipping repair work order (AF Form 1823). d. An updated copy of the original LTI.

d. An updated copy of the original LTI.

89. (017) During the MaxxPro Mine-Resistant, Ambush-Protected (MRAP) vehicle fire suppression system (FSS) inspection, which of the following is not one of the three functional tests to be performed? a. Far. b. Near. c. Dual. d. Combination.

d. Combination.

6. (203) The Fiat Allis crawler tractor's bucket clamshell uses which type of hydraulic cylinder? a. Vane. b. Piston. c. Single-acting. d. Double-acting.

d. Double-acting.

1. (001) As a vehicle management (VM) work center supervisor, which are specific responsibilities that you have? a. Ensuring proper tools are readily available, researching parts, troubleshooting vehicles. b. Assigning work, enforcing safety procedures, filling work orders, and maintaining technical orders. c. Assigning work, coordinating with other sections, scheduling-in maintenance, and monitoring bench stock. d. Ensuring proper tools are readily available, assigning work, enforcing safety procedures, and meeting training needs.

d. Ensuring proper tools are readily available, assigning work, enforcing safety procedures, and meeting training needs.

48. (009) In regards to vehicle maintenance (VM), on-scene repair is the goal of which maintenance concept? a. Minor. b. Triage. c. Organizational. d. Expanded mobile.

d. Expanded mobile.

5. (203) Which type of parking brake is used on the Fiat Allis crawler tractor? a. Internal expanding. b. External expanding. c. Internal contracting. d. External contracting.

d. External contracting.

85. (017) While in the electrical system diagnostic mode on the MaxxPro Mine-Resistant, AmbushProtected (MRAP) vehicle, what action is not required to clear diagnostic trouble codes? a. Turn the left turn signal ON. b. Press the cruise control ON switch. c. Press the cruise control SET switch. d. Hold the SELECT/RESET button on the cluster.

d. Hold the SELECT/RESET button on the cluster.

52. (011) What program is used to access the current mission capable (MC) rate for your base? a. Vehicle Master List. b. Transaction Request Tool (TRT). c. On-Line Vehicle Interactive Management System. d. Logistics Installation and Mission Support Enterprise View (LIMS-EV).

d. Logistics Installation and Mission Support Enterprise View (LIMS-EV).

9. (003) Who specifically authorizes substitutions for vehicles already programmed for depot? a. Major command (MAJCOM). b. Robins Air Force Base (AFB) Special Equipment and Vehicles (SE&V). c. Headquarters United States Air Force (HQ USAF). d. Logistics readiness squadron (LRS) commander.

d. Logistics readiness squadron (LRS) commander.

72. (014) What position should the 2½-ton M-series transfer case lever be in during heavy load operation modes? a. Pushed in to HIGH position. b. Pulled out to LOW position. c. Pulled up to HIGH position. d. Pushed down to LOW position.

d. Pushed down to LOW position.

35. (008) Which document gives a list of all the shop's expenditures by element of expense/investment code (EEIC)? a. Vehicle master list. b. Daily document register. c. Vehicle management (VM) report. d. Responsibility center/cost center (RC/CC) manager's report.

d. Responsibility center/cost center (RC/CC) manager's report.

18. (004) Which statement best describes the man-hour availability factor (MAF)? a. The amount of time an individual is authorized to work on a task. b. A list of industry standards used to determine how long a specific task should take. c. The amount of time an individual is authorized to take to complete a task for their skill level. d. The amount of time an individual is normally available to do the tasks identified in the manpower standard.

d. The amount of time an individual is normally available to do the tasks identified in the manpower standard.

15. (004) Choose the phrase that best describes personnel. a. The total number of positions assigned to an organization. b. The total number of personnel assigned to an organization. c. The total number of jobs or positions required to accomplish a particular mission. d. The individuals that fill the positions required to accomplish a particular mission.

d. The individuals that fill the positions required to accomplish a particular mission.

3. (001) Aside from Fleet Management and Analysis (FM&A) and Materiel Control, what other two shops will "main-shop" supervisors coordinate with daily? a. Customer Service Center (CSC) and Body. b. Fire Truck and Refueling. c. CSC and Tire. d. Tire and Body.

d. Tire and Body.

29. (007) As a work center supervisor, with whom would you work to create master training plans (MTP) and individual training plans (ITP)? a. Vehicle fleet manager (VFM)/vehicle management superintendent (VMS). b. Another work center supervisor. c. Unit commander. d. Unit training manager (UTM).

d. Unit training manager (UTM).

4. (002) With whom should you communicate when vehicle repair work is delayed due to other shop priorities taking precedence? a. Fleet Management and Analysis (FM&A) and using organization. b. FM&A and Customer Service Center (CSC). c. Vehicle fleet manager (VFM), vehicle management superintendent (VMS) and CSC. d. VFM, VMS, and FM&A.

d. VFM, VMS, and FM&A.

40. (008) The Defense Property Accountability System (DPAS) places costs in the reimbursable/refundable file a. during end-of-week processing. b. during end-of-day processing. c. when the work order closes. d. as the costs occur.

d. as the costs occur.

41. (008) Fleet Management and Analysis (FM&A) should furnish the base comptroller's budget office with a list of supported tenant organizations a. only when the budget office requests the data. b. only at the beginning of each fiscal year. c. only at the beginning of each calendar year. d. at the beginning of each fiscal year and when a change is required.

d. at the beginning of each fiscal year and when a change is required.

58. (012) Post changes to the Custodian Authorization/Custody Receipt Listing (CA/CRL) a. at the bottom of the CA/CRL. b. by whiting out old data and enter the new data. c. between the lines and in the same sequence as the CA/CRL. d. by drawing a single line through the old data and enter the new data.

d. by drawing a single line through the old data and enter the new data.

25. (005) Items that are needed to outfit an individual stationed in a cold weather area are called a. supplies. b. properties. c. seasonal issue. d. individual equipment.

d. individual equipment.

29. (009) A package of flyaway spare parts to be shipped with a vehicle before its departure is referred to as a. bench stock parts. b. triage maintenance kit. c. war readiness material kit. d. temporary mission support kit (TMSK).

d. temporary mission support kit (TMSK).

91. (018) The process of assessing damage, putting the priority vehicles first, and doing cannibalization or whatever it takes to get those vehicles back in commission is called a. expanded mobile maintenance. b. organizational maintenance. c. intermediate maintenance. d. triage maintenance.

d. triage maintenance.