BCT 00104 MODULE

Ace your homework & exams now with Quizwiz!

How much of a gap should there be between the wheel guard and the wheel on a bench​ grinder?

1/4

On a bench​ grinder, the distance between the tool rest and the wheel should be​ _____.

1/8-inch

The maximum operating pressure of a pneumatic nailer is typically​ ____ psi.

120

Some hydraulic cylinders can lift more than​ ____.

500 Tons

The most popular circular saw blade size is​ _____ inches.

71/4

A(n) ________ is a​ substance, such as​ sandpaper, that is used to wear away material.

Abrasive

Pneumatic tools get their power from​ _____.

Air pressure

​________ reverses its direction at regularly recurring​ intervals; this type of current is delivered through wall plugs.

Alternating current ( A/C)

The​ _____ describes the maximum amps a battery can provide continuously for up to 60 minutes

Amp Hour

Which of the following grinders is used to grind away​ hard, heavy​ material?

Angel grider

​______ grinders are used to grind away​ hard, heavy materials and to grind surfaces such as​ pipes, plates, or welds.

Angle

Use​ a(n) ________ to bore holes in wood and other materials.

Auger Bit

Masonry bits and​ nail-cutter saw blades have​ a(n) ________ tip.

Carbine

A masonry bit is able to drill into concrete and similar material because it has a​ _____.

Carbine tip

Complete charge and discharge sequences for rechargeable batteries are​ _____.

Charge Cycle

The​ ________ of the drill holds the drill bit.

Chuck

​A(n) ________ is used to open and close the chuck on a power drill.

Chuck Key

Which accessory is sometimes used for cutting holes in stone or composite​ materials, such as those used for​ countertops?

Coring bit

​A(n) ________ is used to set the head of a screw at or below the surface of the material.

Countersink

Which of the following saws cuts by​ friction?

Cutoff

The blade on a power miter saw can be tilted vertically. True or False

False

When loading a​ powder-actuated tool, feed the pin or stud into the​ piston, followed by the gunpowder cartridge.

False

A bit used on wood that is good for boring a​ flat-bottom hole is​ a(n) ______.

Forstner bit

If a​ flat-bottomed hole is needed in a piece of​ lumber, use a​ ________.

Forstner bit

A​ sand-like material used to make a surface​ rough, graded by its​ size, is called​ ________.

Grit

To prevent an electrical​ shock, do not operate electric power tools without proper​ ________.

Ground Fault Protection

A(n) ________ protects people from electric shock and protects equipment from damage by interrupting the flow of electricity if an electrical fault occurs.

Ground fault circuit interrupter (GFCI)

Which accessories can be added to a portable grinder to provide additional protection when special grinding discs are​ used?

Guards and shields

On a job​ site, a portable band saw is almost exclusively used for cutting​ _____.

Heavy metal

What type of saw is used to make curved cuts in​ plywood?

Jigsaw

A​ ________ is created by a saw blade as it cuts through the material.

Kerf

Twist drill bits are used to drill holes in all of the following materials except​ _____.

Masonry

A​ ________ is used to bore holes in​ brick, block, and similar materials.

Masonry bit

Which of the following saws cuts by​ friction?

Miter

Which of the following tools is a pneumatic​ tool?

Nailer

Which type of tools are powered by air​ energy?

Pneumatic

​_______ have traditionally been the choice of craftworkers nailing into concrete and steel.

Pneumatic and​ powder-actuated tools

What type of saw is designed for more​ heavy-duty jobs than the​ jigsaw?

Reciprocating

Which type of saw is often referred to as a SawZall®​?

Reciprocating

​A(n) ________​ saw's straight blades move backward and forward along a straight line.

Reciprocating

Which type of saw blade has square chisel teeth that cut wood parallel with the grain and are generally larger than other types of blade​ teeth?

Rip

The most important item of PPE that should be worn when using any drill is​ _____.

Safety glasses

The​ ________ is the smooth part of a drill bit that fits into the chuck.​

Shank

Before loading a bit in an electric​ drill, make sure​ _____.

The drill is unplugged

Question content area top Part 1 Why is it unacceptable to use a​ powder-actuated tool to fasten a plywood sheet to a wall​ stud?

The fastener can easily pass through both​ materials, causing an injury.

The​ _____ is the turning force of the drill.

Torque

Activating the​ ________ will make the trigger stay in the operating mode even when it is released.

Trigger lock

After placing the tip of the bit of a hammer drill on the indent or​ mark, apply pressure on the drill against the surface before drilling. True or False

True

Impact wrenches are available in pneumatic and electric models. True or False

True

Make sure to remove the power source before repairing any​ electric, pneumatic, or hydraulic tool. True or False

True

The operator of a​ powder-actuated tool must be certified to operate that tool. True or False

True

Use the​ low-speed setting on a reciprocating saw when cutting a steel pipe. True or False

True

Wheels used on bench grinders must not be operated in excess of their rated maximum speed True or False

True

The​ _____ prevents hoses from snapping back if they are inadvertently disconnected.

Whip Check

When finished grinding with a​ hand-held grinder, remove any loose material with a​ _____.

Wire brush

Powder-actuated fastening systems are used to​ _____.

anchor static loads to concrete

Using a trigger lock to lock a​ tool's trigger in an On position​ _____.

can be dangerous and cause injury

Table saws with​ 10-inch blades are excellent for​ _____.

carpentry jobs

A sliding compound miter saw has a rail that allows the blade to slide forward and​ backward, which enables the saw to​ _____.

cut wider material than a standard miter saw

Which of the following saws cuts by​ friction?

cutoff

The first step to prepare a power drill is to​ _____.

disconnect it from its power source

Question content area top Part 1 Hydraulic jacks are used when the application calls for​ _____.

extreme force to be applied

Before using a reciprocating saw to cut through a wall or​ partition, always​ _____.

find out what is on the other side

When cutting with a circular​ saw, grip the saw handles​ _____.

firmly with two hands

On a job​ site, a portable band saw is almost exclusively used for cutting​ _____.

heavy metal

A typical​ lever-operated pump kit includes all of the following except​ _____.

hydraulic fluid

A pneumatic impact wrench requires the use of​ _____.

impact sockets that are designed for the applicable tool

Each of the following are safe practices when using a​ powder-actuated tool except​______________.

loading the tool before the item is ready to be fastened

The most common use of the power drill is to​ _____.

make holes in​ wood, metal, and plastic

Compared to a common​ drill, an impact driver has​ _____.

more torque

Each of the following are safe practices when using a hydraulic jack ​except____________.

placing a pipe on the handle to increase pumping leverage

A detail grinder smoothes and polishes intricate metallic work by using attachments called​ _____.

points

The electromagnetic drill is a​ _____.

portable drill used on thick metal

An example of an electric power drill that is designed to be used in tight spaces is​ a(n) _____.

right - angle drill

The high speed setting on a reciprocating saw is used for​ _____.

sawing wood and other soft materials

The end grinder is used to​ _____.

smooth the inside of​ materials, such as pipe

Use only a band saw that has a​ _____.

stop

Porta-Power® cylinders are rated by how much weight they can lift and by​ _____.

the distance they can move the weight

The blade of an abrasive cutoff saw spins at such a high speed that​ _____.

the resulting friction is hot enough to burn through the material

When using a​ jigsaw, avoid vibration by​ _____.

using a clamp or vise to hold the work

When operating a power​ tool, it is important to always​ _____.

wear the proper PPE

Hammer drills are designed to drill into​ _____.

​concrete, brick, and tile


Related study sets

Deleon Chemistry- Chapter 7 test answers

View Set

Cognitive-Behavioral Family Therapy

View Set

Unit 5 Review: Industrialization & Global integration 1750-1900

View Set

The cte shop study set unit 15 & 16

View Set

oxygenation Exemplar 15.F Sudden Infant Death Syndrome

View Set

Dispensing In The Community Pharmacy (Ch. 7)

View Set

Chapter 21: Revolutions and Nation Building, 1848-1871

View Set