CCNA FINAL EXAM GRADE 1
How does standby preemption affect the router configured with the highest priority in the HSRP group? (Select two.)
If the active router fails, but then regains service, it does not become the active router when preemption is not. and If the active router fails, but then regains service, it becomes the active router again when preemption is enable.
Which of the following are reasons to configure VLANs on a switch as opposed to using switches without VLANs? (Select two.)
Increased security. and Increased broadcast domains.
Which of the following does not accurately describe the HSRP states?
Learn is when the router has received the virtual IP address from a hello message by the active router.
Which of the following protocols provide gateway redundancy? (Select all that apply.)
HSRP and VRRP
Which of the following is required before you can create an SVI?
A vlan must be created in the Vlan database.
You have two switches connected together as shown in the following diagram. How many broadcast domains are there in the network shown?
2
Which of the following best describes the various HSRP group roles? (Select two.)
An active router forwards traffic destined to the virtual address. and a standby router will become the active router should the existing active router fail.
Computers A and B are on the same VLAN and are separated by two switches, as shown in the Exhibit. Computer A sends a frame to Computer B. Which of the following best describes the composition of the frame as it travels from A to B?
Computer A sends a normal frame.The first switch appends a vlan id to the frame.The second switch removes the vlan id before forwarding it to computer B.
You have two VLANs and two Cisco 1841 routers as shown in the exhibit.How can you configure HSRP to share the load from the two VLANs? (Select two.)
Configure RouterA to serve as the active router for vlan 2 and backup router for vlan 4. and Configure RouterB to serve as the active router for vlan 4 and backup router for vlan 2.
Which of the following are true regarding using multiple VLANs on a single switch? (Select two.)
The number of broadcast domain increases. and The number of collision domain stays the same.
You have two routers that should be configured for gateway redundancy. The following commands are entered for each router: A(config)#int fa 0/2A(config-if)#ip address 172.16.1.2A(config-if)#standby 2 priority 150A(config-if)#standby 2 ip 172.16.0.1B(config)#int fa 0/2B(config-if)#ip address 172.16.1.3B(config-if)#standby 2 priority 150Which of the following is true? (Select two.)
The virtual ip address is 172.16.0.1. and RouterB will serve as an active router. RouterA will serve as standby router
You have configured inter-VLAN routing on a Catalyst 3550 switch. You enter the show run command and receive the output as shown in the exhibit.Which of the following is true? (Select two.)
Traffic sent from Vlan 2 to Vlan 3 will not reach vlan 3. and Interface Vlan 2 is enabled with the no shutdown interface configuration command.
You have configured inter-VLAN routing on a Catalyst 3550 switch. You enter the show ip route command and receive the output as shown in the exhibit.Which of the following is true? (Select two.)
Traffic sent with vlans 2, 3, and 11 will be router on the 3550 switch. and vlan 11 has a virtual ip address in the 10.1.11.0 network.
You have configured inter-VLAN routing on a Catalyst 3550 switch. Hosts belonging to VLAN 2 cannot contact servers belonging to VLAN 3. To troubleshoot the issue, you enter the show ip route command and receive the output as shown in the exhibit.Which of the following may be true? (Select two.)
Vlan 2 does not have an interface ip address. and The vlan 2 interface is not enabled with the no shutdown command
You want to verify that interface fastEthernet 0/2 is a member of VLAN0002. Which command displays the output shown here?VLAN Name Status Ports---- --------------------- --------- -------------------------------1 default active Fa0/3, Fa0/4, Fa0/5, Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11, Fa0/12, Gi0/1, Gi0/22 VLAN0002 active Fa0/21002 fddi-default active1003 token-ring-default active1004 fddinet-default active1005 trnet-default active...(output suppressed)
show vlan brief