Chapter quizzes
If a router has two interfaces and is routing both IPv4 and IPv6 traffic, how many ACLs could be created and applied to it? 4 6 8 12 16
8
As a DHCPv4 client lease is about to expire, what is the message that the client sends the DHCP server? DHCPDISCOVER DHCPOFFER DHCPREQUEST DHCPACK
DHCPREQUEST
A company implements the stateless DHCPv6 method for configuring IPv6 addresses on employee workstations. After a workstation receives messages from multiple DHCPv6 servers to indicate their availability for DHCPv6 service, which message does it send to a server for configuration information? DHCPv6 SOLICIT DHCPv6 REQUEST DHCPv6 ADVERTISE DHCPv6 INFORMATION-REQUEST
DHCPv6 INFORMATION-REQUEST
What two methods can be used to generate an interface ID by an IPv6 host that is using SLAAC? (Choose two.) EUI-64 random generation stateful DHCPv6 DAD ARP
EUI-64 random generation
A company uses DHCP servers to dynamically assign IPv4 addresses to employee workstations. The address lease duration is set as 5 days. An employee returns to the office after an absence of one week. When the employee boots the workstation, it sends a message to obtain an IP address. Which Layer 2 and Layer 3 destination addresses will the message contain? FF-FF-FF-FF-FF-FF and 255.255.255.255 both MAC and IPv4 addresses of the DHCP server MAC address of the DHCP server and 255.255.255.255 FF-FF-FF-FF-FF-FF and IPv4 address of the DHCP server
FF-FF-FF-FF-FF-FF and 255.255.255.255
Refer to the following output. What is the significance of the 4 match(es) statement? R1# <output omitted>10 permit 192.168.1.56 0.0.0.720 permit 192.168.1.64 0.0.0.63 (4 match(es))30 deny any (8 match(es)) - Four packets have been denied that have been sourced from any IP address. - Four packets have been denied that are destined for the 192.168.1.64 network. - Four packets have been allowed through the router from PCs in the network of 192.168.1.64. - Four packets have been allowed through the router to reach the destination network of 192.168.1.64/26
Four packets have been allowed through the router from PCs in the network of 192.168.1.64.
An administrator has configured an access list on R1 to allow SSH administrative access from host 172.16.1.100. Which command correctly applies the ACL? R1(config-if)# ip access-group 1 in R1(config-if)# ip access-group 1 out R1(config-line)# access-class 1 in R1(config-line)# access-class 1 out
R1(config-line)# access-class 1 in
What is the result of a network technician issuing the command ip dhcp excluded-address 10.0.15.1 10.0.15.15 on a Cisco router? The Cisco router will exclude 15 IP addresses from being leased to DHCP clients. The Cisco router will allow only the specified IP addresses to be leased to clients. The Cisco router will exclude only the 10.0.15.1 and 10.0.15.15 IP addresses from being leased to DHCP clients. The Cisco router will automatically create a DHCP pool using a /28 mask.
The Cisco router will exclude 15 IP addresses from being leased to DHCP clients.
Under which two circumstances would a router usually be configured as a DHCPv4 client? (Choose two.) The router is intended to be used as a SOHO gateway. The administrator needs the router to act as a relay agent. The router is meant to provide IP addresses to the hosts. This is an ISP requirement. The router has a fixed IP address.
The router is intended to be used as a SOHO gateway. This is an ISP requirement.
What single access list statement matches all of the following networks? 192.168.16.0 192.168.17.0 192.168.18.0 192.168.19.0 - access-list 10 permit 192.168.16.0 0.0.3.255 - access-list 10 permit 192.168.16.0 0.0.0.255 - access-list 10 permit 192.168.16.0 0.0.15.255 - access-list 10 permit 192.168.0.0 0.0.15.255
access-list 10 permit 192.168.16.0 0.0.3.255
Which DHCPv4 message will a client send to accept an IPv4 address that is offered by a DHCP server? unicast DHCPACK broadcast DHCPACK unicast DHCPREQUEST broadcast DHCPREQUEST
broadcast DHCPREQUEST
Which address does a DHCPv4 server target when sending a DHCPOFFER message to a client that makes an address request? client IP address client hardware address gateway IP address broadcast MAC address
client hardware address
An administrator issues the commands: Router(config)# interface g0/1Router(config-if)# ip address dhcp What is the administrator trying to achieve? configuring the router to act as a DHCPv4 server configuring the router to obtain IP parameters from a DHCPv4 server configuring the router to act as a relay agent configuring the router to resolve IP address conflicts
configuring the router to obtain IP parameters from a DHCPv4 server
Which is a DHCPv4 address allocation method that assigns IPv4 addresses for a limited lease period? manual allocation pre-allocation automatic allocation dynamic allocation
dynamic allocation
Which type of ACL statements are commonly reordered by the Cisco IOS as the first ACEs? host range permit any lowest sequence number
host
On which router should the show access-lists command be executed? - on the router that routes the packet referenced in the ACL to the final destination network - on the router that routes the packet referenced in the ACL from the source network - on any router through which the packet referenced in the ACL travels - on the router that has the ACL configured
on the router that has the ACL configured
What is used in the EUI-64 process to create an IPv6 interface ID on an IPv6 enabled interface? the MAC address of the IPv6 enabled interface a randomly generated 64-bit hexadecimal address an IPv6 address that is provided by a DHCPv6 server an IPv4 address that is configured on the interface
the MAC address of the IPv6 enabled interface
A company uses the SLAAC method to configure IPv6 addresses for the employee workstations. Which address will a client use as its default gateway? the all-routers multicast address the link-local address of the router interface that is attached to the network the unique local address of the router interface that is attached to the network the global unicast address of the router interface that is attached to the network
the link-local address of the router interface that is attached to the network
Which type of router connection can be secured by the access-class command? vty console serial Ethernet
vty
In which configuration would an outbound ACL placement be preferred over an inbound ACL placement? - when the ACL is applied to an outbound interface to filter packets coming from multiple inbound interfaces before the packets exit the interface - when a router has more than one ACL - when an outbound ACL is closer to the source of the traffic flow - when an interface is filtered by an outbound ACL and the network attached to the interface is the source network being filtered within the ACL
when the ACL is applied to an outbound interface to filter packets coming from multiple inbound interfaces before the packets exit the interface
Which three statements describe ACL processing of packets? (Choose three.) - An implicit deny any rejects any packet that does not match any ACE. - A packet can either be rejected or forwarded as directed by the ACE that is matched. - A packet that has been denied by one ACE can be permitted by a subsequent ACE. - A packet that does not match the conditions of any ACE will be forwarded by default. - Each statement is checked only until a match is detected or until the end of the ACE list. - Each packet is compared to the conditions of every ACE in the ACL before a forwarding decision is made.
An implicit deny any rejects any packet that does not match any ACE. A packet can either be rejected or forwarded as directed by the ACE that is matched. Each statement is checked only until a match is detected or until the end of the ACE list.
Which three statements are generally considered to be best practices in the placement of ACLs? (Choose three.) - Place standard ACLs close to the source IP address of the traffic. - Place extended ACLs close to the destination IP address of the traffic. - Filter unwanted traffic before it travels onto a low-bandwidth link. - Place extended ACLs close to the source IP address of the traffic. - Place standard ACLs close to the destination IP address of the traffic. - For every inbound ACL placed on an interface, there should be a matching outbound ACL
Filter unwanted traffic before it travels onto a low-bandwidth link. Place extended ACLs close to the source IP address of the traffic. Place standard ACLs close to the destination IP address of the traffic.
Which statement describes a difference between the operation of inbound and outbound ACLs? - In contrast to outbound ALCs, inbound ACLs can be used to filter packets with multiple criteria. - Inbound ACLs can be used in both routers and switches but outbound ACLs can be used only on routers. - Inbound ACLs are processed before the packets are routed while outbound ACLs are processed after the routing is completed. - On a network interface, more than one inbound ACL can be configured but only one outbound ACL can be configured.
Inbound ACLs are processed before the packets are routed while outbound ACLs are processed after the routing is completed.
What is an advantage of configuring a Cisco router as a relay agent? It will allow DHCPDISCOVER messages to pass without alteration. It can forward both broadcast and multicast messages on behalf of clients. It can provide relay services for multiple UDP services. It reduces the response time from a DHCP server.
It can provide relay services for multiple UDP services.
How does an IPv6 client ensure that it has a unique address after it configures its IPv6 address using the SLAAC allocation method? It sends an ARP message with the IPv6 address as the destination IPv6 address. It checks with the IPv6 address database that is hosted by the SLAAC server. It contacts the DHCPv6 server via a special formed ICMPv6 message. It sends an ICMPv6 Neighbor Solicitation message with the IPv6 address as the target IPv6 address.
It sends an ICMPv6 Neighbor Solicitation message with the IPv6 address as the target IPv6 address.
A network administrator configures a router to send RA messages with M flag as 0 and O flag as 1. Which statement describes the effect of this configuration when a PC tries to configure its IPv6 address? It should contact a DHCPv6 server for all the information that it needs. It should use the information that is contained in the RA message exclusively. It should use the information that is contained in the RA message and contact a DHCPv6 server for additional information. It should contact a DHCPv6 server for the prefix, the prefix-length information, and an interface ID that is both random and unique.
It should use the information that is contained in the RA message and contact a DHCPv6 server for additional information.
A network administrator needs to configure a standard ACL so that only the workstation of the administrator with the IP address 192.168.15.23 can access the virtual terminal of the main router. Which two configuration commands can achieve the task? (Choose two.) Router1(config)# access-list 10 permit host 192.168.15.23 Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.0 Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.255 Router1(config)# access-list 10 permit 192.168.15.23 255.255.255.0 Router1(config)# access-list 10 permit 192.168.15.23 255.255.255.255
Router1(config)# access-list 10 permit host 192.168.15.23 Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.0
A network administrator is configuring an ACL to restrict access to certain servers in the data center. The intent is to apply the ACL to the interface connected to the data center LAN. What happens if the ACL is incorrectly applied to an interface in the inbound direction instead of the outbound direction? All traffic is denied. All traffic is permitted. The ACL does not perform as designed. The ACL will analyze traffic after it is routed to the outbound interface
The ACL does not perform as designed.
What is the effect of configuring an ACL with only ACEs that deny traffic? The ACL will permit any traffic that is not specifically denied. The ACL will block all traffic. The ACL must be applied inbound only. The ACL must be applied outbound only.
The ACL will block all traffic.
Consider the following output for an ACL that has been applied to a router via the access-class in command. What can a network administrator determine from the output that is shown? R1# <output omitted>Standard IP access list 210 permit 192.168.10.0, wildcard bits 0.0.0.255 (2 matches)20 deny any (1 match) - Two devices connected to the router have IP addresses of 192.168.10.x. - Traffic from one device was not allowed to come into one router port and be routed outbound a different router port. - Two devices were able to use SSH or Telnet to gain access to the router. - Traffic from two devices was allowed to enter one router port and be routed outbound to a different router port
Two devices were able to use SSH or Telnet to gain access to the router.
What is the quickest way to remove a single ACE from a named ACL? - Use the no keyword and the sequence number of the ACE to be removed. - Use the no access-list command to remove the entire ACL, then recreate it without the ACE. - Copy the ACL into a text editor, remove the ACE, then copy the ACL back into the router. - Create a new ACL with a different number and apply the new ACL to the router interface
Use the no keyword and the sequence number of the ACE to be removed.
Which address is required in the command syntax of a standard ACL? source MAC address destination MAC address source IP address destination IP address
source IP address
An administrator wants to configure hosts to automatically assign IPv6 addresses to themselves by the use of Router Advertisement messages, but also to obtain the DNS server address from a DHCPv6 server. Which address assignment method should be configured?SLAAC stateless DHCPv6 stateful DHCPv6 RA and EUI-64
stateless DHCPv6
Which feature will require the use of a named standard ACL rather than a numbered standard ACL? - the ability to filter traffic based on a specific protocol - the ability to filter traffic based on an entire protocol suite and destination - the ability to specify source and destination addresses to use when identifying traffic - the ability to add additional ACEs in the middle of the ACL without deleting and re-creating the list
the ability to add additional ACEs in the middle of the ACL without deleting and re-creating the list
When would a network administrator use the clear access-list counters command? when obtaining a baseline when buffer memory is low when an ACE is deleted from an ACL when troubleshooting an ACL and needing to know how many packets matched
when troubleshooting an ACL and needing to know how many packets matched
