EASA Part 66 : Material Question14
Question Number. 33. If a sheet of aluminium alloy of 0.032 and 0.064 is to be joined together the rivet should be. Option A. 0.032 plus 2D. Option B. 0.096 plus 1.5 D. Option C. 0.064 plus 1D.
Correct Answer is. 0.096 plus 1.5 D. Explanation. Rivet allowance is 1.5D. Sheet thickness is 0.032 + 0.064 inches.
Question Number. 12. Rivet allowance is. Option A. 1.5d. Option B. 1d plus the thickness of the material. Option C. 1.5d plus the thickness of the material.
Correct Answer is. 1.5d. Explanation. Rivet allowance is 1.5 * diameter.
Question Number. 28. The length of solid rivets is in graduations of. Option A. 1/16 inch. Option B. 1/8 inch. Option C. 1/4 inch.
Correct Answer is. 1/16 inch. Explanation. CAIP BL/6-27.
Question Number. 29. What would be the diameter and length of a solid rivet if the following markings are given, AS 162-408?. Option A. ¼ inch dia, ½ inch length. Option B. ½ inch dia, 1 inch length. Option C. 1/8 inch dia, ½ inch length.
Correct Answer is. 1/8 inch dia, ½ inch length. Explanation. CAIP BL/6-27.
Question Number. 53. The dimensions of an MS20430AD-4-8 rivets are. Option A. 1/8 inch in diameter and 1/2 inch long. Option B. 4/16 inch in diameter and 8/32 inch long. Option C. 1/8 inch in diameter and 1/4 inch long.
Correct Answer is. 1/8 inch in diameter and 1/4 inch long. Explanation. AC 43.13-1B Chap 4 fig 4-4 on page 4-16.
Question Number. 37. Countersunk rivets have two angles of countersink, these are. Option A. 100 - 115 degrees. Option B. 125 - 135 degrees. Option C. 100 -160 degrees.
Correct Answer is. 100 - 115 degrees. Explanation. None of these are correct, but since there are 3 countersink angles (90, 100, 120) c is closest. BL/6-27 3.2.
Question Number. 16. A countersunk rivet of the 'SP' series has a head style of. Option A. 20 °. Option B. 90 °. Option C. 100 °.
Correct Answer is. 100 °. Explanation. SP series rivets are 100 degree csk. BL/6-27 3.3.
Question Number. 54. The primary alloying agent of 2024-T36 rivets is indicated by the number. Option A. 20. Option B. 2. Option C. 24.
Correct Answer is. 2. Explanation. CAIP BL/6-27 para 4.1.
Question Number. 57. Which rivet may be used as received without further treatment?. Option A. 2017-T3. Option B. 2117-T3. Option C. 2024-T4.
Correct Answer is. 2117-T3. Explanation. 2117 is an 'AD' rivet.
Question Number. 42. Cadmium plated rivets should not be used where the temperature may exceed. Option A. 120 °C. Option B. 250 °C. Option C. 200 °C.
Correct Answer is. 250 °C. Explanation. BL/6-27 5.1.
Question Number. 15. An American rivet with a cross on the head is. Option A. 2124 aluminium alloy. Option B. 2117 aluminium alloy. Option C. 5056 aluminium alloy.
Correct Answer is. 5056 aluminium alloy. Explanation. A cross on the head of a rivet indicates it is 5056 al.alloy.
Question Number. 9. What metal is suitable for riveting magnesium alloy?. Option A. Monel metal. Option B. 5056 aluminium alloy. Option C. 1100 aluminium alloy.
Correct Answer is. 5056 aluminium alloy. Explanation. BL/6-27 5.1 and AC43 7-1 para.d.
Question Number. 31. What is the pressure range for the Avdel Riveter type F?. Option A. 60 to 80 psi. Option B. 20 to 60 psi. Option C. 40 to 60 psi.
Correct Answer is. 60 to 80 psi. Explanation. 60 to 80 psi.
Question Number. 47. A plate 10 inches by 5 inches is to be riveted with 3 rows of rivets, with the normal 4D rivet spacing and 2 D edge distance. The rivets are AN460AD4-6. How many rivets are required?. Option A. 60. Option B. 52. Option C. 56.
Correct Answer is. 60. Explanation. Rivet diameter = 4/32 = 1/8 inch. If it is to be riveted along the 10 inch length, subtract the edge distances (2 * 1/4 inch) = 9 and a 1/2 inches. 4D = 1/2 inch. You can fit 20 rivets in 9 1/2 inches. 3 * 20 = 60.
Question Number. 22. If you can only gain limited access to both sides of a structure, what would you use to repair the structure?. Option A. A hylok. Option B. A blind rivet. Option C. A pop rivet.
Correct Answer is. A hylok. Explanation. Pop rivets and blind rivets cannot be used in place of solid rivets. Jeppesen A&P Airframe Handbook Pg.155.
Question Number. 25. A rivet with no marking has the material code. Option A. AD. Option B. A. Option C. D.
Correct Answer is. A. Explanation. NIL.
Question Number. 4. How is a British aluminium rivet identified?. Option A. Black anodic finish. Option B. Natural anodised finish. Option C. Violet anodic finish.
Correct Answer is. Black anodic finish. Explanation. A British aluminium rivet is black anodised.
Question Number. 5. A BS rivet made from L36 would be what colour and marking?. Option A. Black anodic with an 'A'. Option B. Natural anodic with no marking. Option C. Green anodic with an 'X'.
Correct Answer is. Black anodic with an 'A'. Explanation. An L36 rivet is anodised black.
Question Number. 40. On a structural repair, what type of rivet would you use when the back side cannot be accessed?. Option A. Pop rivet. Option B. Hi-loc rivet. Option C. Blind rivet.
Correct Answer is. Blind rivet. Explanation. By elimination, no such thing as a hi-loc rivet, and pop rivets may cause a FOD problem due to the stem falling out. BL/6-28 Para.2.
Question Number. 26. Rivet MS20426 has what head type?. Option A. CSK. Option B. Universal. Option C. Round.
Correct Answer is. CSK. Explanation. CAIP BL/6-27 table 4.
Question Number. 11. An aluminium alloy L37 rivet identification is. Option A. X embossed. Option B. O embossed. Option C. D embossed.
Correct Answer is. D embossed. Explanation. An aluminium alloy L37 (Duralumin) rivet is identified with an 'D'.
Question Number. 6. What do the letters and numbers on a British rivet mean?. Option A. Material specification only. Option B. Material and finish. Option C. Head shape, material and finish.
Correct Answer is. Head shape, material and finish. Explanation. Example SP80 is snap head, al alloy, violet finish. BL/6-27 3.
Question Number. 45. What type loads cause the most rivet failures?. Option A. Bearing. Option B. Shear. Option C. Head.
Correct Answer is. Head. Explanation. NIL.
Question Number. 34. Where would a pop rivet with a break stem mandrel be used?. Option A. In a closed structure. Option B. Where the head can be retrieved. Option C. Any situation calling for a pop rivet.
Correct Answer is. In a closed structure. Explanation. A pop rivet is not a truly blind rivet because the tail falls away and has to be retrieved. However, the break-stem pop rivet has a head which stays with the rivet after breaking.
Question Number. 30. What would the marking .5 indicate after the normal part number of a solid rivet?. Option A. The rivet length in graduations of 1/8 inch. Option B. The diameter of the rivet is half an inch. Option C. Indicates close tolerance rivet.
Correct Answer is. Indicates close tolerance rivet. Explanation. CAIP BL/6-27 para 3.
Question Number. 44. What is an advantage of a double flare on aluminium tubing?. Option A. Ease of construction. Option B. It is more resistant to the shearing effect of torque. Option C. It is less resistant to the shearing effect of torque.
Correct Answer is. It is more resistant to the shearing effect of torque. Explanation. NIL.
Question Number. 1. Forming a solution treated rivet gives it 75% of its hardness. What gives it the other 25%?. Option A. Leave at room temperature for four hours. Option B. Precipitation treat the component when forming is complete. Option C. Put them in a refrigerator.
Correct Answer is. Leave at room temperature for four hours. Explanation. NIL.
Question Number. 10. What metal is suitable for riveting alloy steel?. Option A. Aluminium alloy. Option B. Monel metal. Option C. Mild steel.
Correct Answer is. Monel metal. Explanation. BL/6-27 5.1.
Question Number. 43. What rivets should be used with nickel alloy steel?. Option A. Aluminium Alloy. Option B. Mild Steel. Option C. Monel.
Correct Answer is. Monel. Explanation. AC43 Page 7-2 Para.g.
Question Number. 41. What material is suitable for riveting steel?. Option A. Aluminium alloy. Option B. Monel. Option C. Copper.
Correct Answer is. Monel. Explanation. BL/6-27 5.1. Really mild steel should be used (see AC43 7-1 para.e) but that is not an answer given.
Question Number. 61. The four quadrants on a quadrant rivet code system are designated. Option A. N, S, E, W. Option B. top-left, top-right, bottom-left, bottom-right. Option C. NW, NE, SE, SW.
Correct Answer is. NW, NE, SE, SW. Explanation. NIL.
Question Number. 58. The information on rivet grip length is in which rivet code quadrant?. Option A. NW. Option B. SE. Option C. NE.
Correct Answer is. SE. Explanation. NAS-523.
Question Number. 3. A joggle in a removed rivet is indication of what type of partial failure?. Option A. Bearing. Option B. Shear. Option C. Compression.
Correct Answer is. Shear. Explanation. NIL.
Question Number. 49. What type of heat treatment can be used on DD rivets?. Option A. Annealing. Option B. Precipitation. Option C. Solution Treatment.
Correct Answer is. Solution Treatment. Explanation. NIL.
Question Number. 27. What is meant by the term Pitch Ratio?. Option A. The area of contact between the two sheets of metal when joining by rivets. Option B. The distance between the hole and the edge of the material. Option C. The distance between two holes.
Correct Answer is. The distance between two holes. Explanation. CAIP BL/6-29 (Rivet Pitch).
Question Number. 14. What do you do to 2017 and 2024 rivets after heat treatment?. Option A. Leave for a minimum of 2 hours before using. Option B. refrigerate for a minimum of 2 hours before using. Option C. Use immediately or refrigerate.
Correct Answer is. Use immediately or refrigerate. Explanation. NIL.
Question Number. 21. Identification of British aluminium alloy rivets is with. Option A. a part number on the head. Option B. a letter and number code. Option C. a colour and number stamped on the head.
Correct Answer is. a colour and number stamped on the head. Explanation. Aluminium alloy rivets are colour coded with a number or letter on the head.
Question Number. 56. MS20426AD-6-5 indicates a countersunk rivet which has. Option A. a shank length of 5/16 inch (excluding head). Option B. an overall length of 5/16 inch. Option C. a shank length of 5/32 inch (excluding head).
Correct Answer is. an overall length of 5/16 inch. Explanation. NIL.
Question Number. 20. A rivet that has 5% magnesium is identified as. Option A. anodic violet and has an X. Option B. anodic green and has an X. Option C. natural and has an m.
Correct Answer is. anodic green and has an X. Explanation. 5% magnesium rivets are green anodized. BL/6-27 Table 1.
Question Number. 48. A new rivet made of aluminium alloy is. Option A. anodised with 's'. Option B. anodised with 'x'. Option C. anodised with 'd'.
Correct Answer is. anodised with 'x'. Explanation. Of the aluminium alloy rivets, L86 is violet with an 's' and L58 is green with an 'x', but L86 (hiduminium) is no longer made.
Question Number. 36. Avdel rivets are closed by. Option A. a tapered mandrel. Option B. broaching. Option C. squeezing.
Correct Answer is. broaching. Explanation. Avdel rivets are closed by broaching. BL/6-29 8.2.2.
Question Number. 39. A 'HUCK' rivet is similar in design to a. Option A. blind rivet. Option B. dome head rivet. Option C. cherry rivet.
Correct Answer is. cherry rivet. Explanation. The Huck rivet is similar in design to the cherry rivet. But both are blind rivets. AC43 4-24.
Question Number. 59. The NE rivet quadrant gives information on. Option A. diameter and manufactured head location. Option B. fastener identity. Option C. head data.
Correct Answer is. diameter and manufactured head location. Explanation. NAS-523.
Question Number. 18. A factor which determines the minimum space between rivets is the. Option A. thickness of the material being riveted. Option B. diameter of the rivets being used. Option C. length of the rivets being used.
Correct Answer is. diameter of the rivets being used. Explanation. Rivet spacing (single row) is 4 * diameter. AC43 4-16.
Question Number. 55. Most rivets used in aircraft construction have. Option A. a raised dot. Option B. dimples. Option C. smooth heads without markings.
Correct Answer is. dimples. Explanation. Most rivets are 2117.
Question Number. 7. A natural finish aluminium alloy rivet with a D on it is. Option A. hiduminium L86. Option B. aluminium L36. Option C. duralumin L37.
Correct Answer is. duralumin L37. Explanation. L37 is aluminium alloy with a D. BL/6-27.
Question Number. 60. A square around the NW digit in the quadrant of a fastner would indicate. Option A. interference fit fastener. Option B. hi-lock to be used. Option C. fluid tight fastner.
Correct Answer is. fluid tight fastner. Explanation. NIL.
Question Number. 8. A 5% magnesium rivet is identified by. Option A. violet anodise with 'S' on it. Option B. green anodise with 'X' or an '8' on it. Option C. black anodise with 'A' on it.
Correct Answer is. green anodise with 'X' or an '8' on it. Explanation. 5% magnesium is green anodised with an 'X' or an '8'.
Question Number. 24. When a solid rivet is formed it only holds 75% of its shear strength, the other 25% comes from. Option A. leaving assembly for 4 days to age harden. Option B. heating the completed assembly. Option C. cooling completed assembly.
Correct Answer is. leaving assembly for 4 days to age harden. Explanation. NIL.
Question Number. 17. The coding of a British rivet indicates. Option A. length and diameter. Option B. head type and colour. Option C. material and head type.
Correct Answer is. material and head type. Explanation. Coding such as SP80 means al.alloy and snap head. BL/6-27 8.
Question Number. 2. If D or DD rivets are not formed in time , or removed from the freezer in time, they. Option A. must be discarded. Option B. must be re-heat treated before use. Option C. can be re-heat treated once then discarded.
Correct Answer is. must be re-heat treated before use. Explanation. NIL.
Question Number. 52. Hole filling fasteners (for example, MS20470 rivets) should not be used in composite structures primarily because of the. Option A. increased possibility of fretting corrosion in the fastener. Option B. difficulty in forming a proper shop head. Option C. possibility of causing delamination.
Correct Answer is. possibility of causing delamination. Explanation. NIL.
Question Number. 38. On a CHERRY MAX rivet, after the riveting process the mandrel section or stem is. Option A. is ground down flush to rivet head. Option B. discarded. Option C. remains in the rivet sleeve to provide mechanical strength.
Correct Answer is. remains in the rivet sleeve to provide mechanical strength. Explanation. The stem remains in the rivet after it is broken off. A collar holds it in place AC43 4-57, 4-24.
Question Number. 13. D and DD rivets are refrigerated to. Option A. precipitation harden. Option B. increase age hardening. Option C. retard age hardening.
Correct Answer is. retard age hardening. Explanation. Refrigeration retards age hardening.
Question Number. 19. Joggles in removed rivet shanks would indicate partial. Option A. torsion failure. Option B. shear failure. Option C. bearing failure.
Correct Answer is. shear failure. Explanation. NIL.
Question Number. 46. Rivet's main strength quality is to resist. Option A. tensile loads. Option B. shear loads. Option C. torsion.
Correct Answer is. shear loads. Explanation. NIL.
Question Number. 23. Alloy rivets are heat treated by. Option A. solution treating. Option B. annealing. Option C. anodising.
Correct Answer is. solution treating. Explanation. Al.Alloy rivets are solution heat treated.
Question Number. 50. The general rule for finding the proper rivet diameter is. Option A. three times the thickness of the thickest sheet. Option B. three times the thickness of the material to be joined. Option C. two times the rivet length.
Correct Answer is. three times the thickness of the material to be joined. OR three times the thickness of the thickest sheet. Explanation. NIL.
Question Number. 35. A chobert rivet gun may be used. Option A. until the end has worn 0.002 inch below nominal diameter. Option B. indefinately. Option C. once only.
Correct Answer is. until the end has worn 0.002 inch below nominal diameter. Explanation. 0.002 inch is the wear limit on a chobert rivet gun. BL/6-29 8.2.1.
Question Number. 51. Cherrymax and Olympic-Lok rivets. Option A. utilize a pulling tool for installation. Option B. may be installed with ordinary hand tools. Option C. utilize a rivet gun, special rivet set, and bucking bar for installation.
Correct Answer is. utilize a rivet gun, special rivet set, and bucking bar for installation. Explanation. NIL.
Question Number. 32. What is the length of the operation stroke of the Avdel Riveter type F?. Option A. ½ inch. Option B. 7/8 inch. Option C. 1 inch.
Correct Answer is. ½ inch. Explanation. 1/2 inch stroke.
