EIC Year 1 Final Exam
I agree and understand
Technical questions including logging into the Online Training Website and navigation of the training site should be directed to - [email protected] Help with understanding a lesson and/or turning in homework should be directed to - [email protected]
C. metal studs
Aviation snips can be used to cut ___.
I understand and agree to comply
7.4 - I understand this is an online program and email is important. I agree to let [email protected] know any changes in my situation, status and/or assistance needed in addition to the instructor session for learning the related instruction.
28
A 1/4 - 28 x 31/2 machine screw has ___ threads per inch.
socket
Which of these wrenches would be safer to use to loosen a frozen nut?
B. cold chisel
Which tool(s) could be (properly) used for cutting, shaping and removing metal that is softer than the tool itself?
E. a and c only
A flat (standard) blade screwdriver blade that ___ of a slot head screw should be selected. A. fits snugly into and reaches the bottom of the slot B. is 1/16" wider than the slot on each side C. is exactly the same width as the slot or slightly less than the slot width D. a and b only E. a and c only
True
A torque screwdriver and a torque wrench are examples of torque tools
is a calibrated tool to apply consistent measured rotational force.
A torque wrench ______
device
A unit of an electrical system, other than a conductor, that carries or controls electric energy as its principal function is referred to as a(n) ___
device
A unit of an electrical system, other than a conductor, that carries or controls electric energy as its principal function is referred to as a(n) ___.
pulling
Adjustable wrenches should be used so that force is applied to the fixed jaw when ___ on the wrench.
I understand and agree
All Electrical Training Apprenticeship Students have access to their grades at the bottom of their log in page.
.164
An 8-32 x 3 machine screw has a diameter of ___ inches.
Article 100
Article ___ in the NEC® distinguishes between an outlet and a receptacle
100
Article ___ in the NEC® distinguishes between an outlet and a receptacle.
Answer = D. Any of these A. damage the screwdriver tip B. hit his hand with the hammer C. get a shaving in his eye D. any of these
As a consequence of Hazardous Harry's actions, as shown below, he could ___.
C. safety glasses
As a minimum (select the ONE best answer), which piece of safety equipment listed below is required to be worn when cutting 12 AWG wire with pliers?
. I agree and will comply
BCES - Reference to "BCES" is Bay Colony Electrical Specifications and Prints. THESE ARE FOUND IN THE CLASSROOM RESOURCE AREA - FIRST PAGE. MAKE SURE YOU CHECK OUT ALL CLASSROOM RESOURCE PAGES.
I understand and agree
Be it noted that - any/and/or all correspondence with on-line students will be copied to the Education Director/Coordinator, Executcive Director and/or Contractor Designee. Exception: Log in Information letter - by law, we are restricted from giving anyone, except the student, login information.
Answer = D all of these A. the correct length for the material to be cut B. sharp C. the proper type for the material to be cut D. all of these
Before using a reciprocating saw ("sawsall"), you should make sure that the blade is ___.
I understand and agree
CPR/1st Aid: CPR and First Aid training - required by the IEC curriculum. Depending on your location - you will receive this training independently of the online related instruction. Check with your IEC Chapter and/or Empoyer for your requirement.
False
Cheater bars can be safely used on a wrench to extend the length of the handle so that additional torque can be applied.
False
Cold chisels are used to split concrete blocks or bricks.
I
Current is represented by the letter or symbol ___.
I understand and agree
Each lesson counts for four (4) hours of attendance for a total of DLLR required 144 hours. The student must complete the lessons within the time frame specified in their schedule to receive credit. Lessons that are incomplete, some homework and/or lab, etc not completed will make the student a fail/drop/incomplete - no credit given.
I understand and agree
Eligibility: Student must meet elibigility requirements for the On-Line Apprenticeship Training Program and must be approved by: 1) Employer 2) Apprenticeship Director or IEC Chapter 3) Non Member eligibility available Consideration will be on an individual basis. Students must have a computer system with minimum software applications (as noted on website), equipment and internet speed needed for online access.
I understand and agree
Enrollment in the online related instruction - As soon as students are enrolled and books are available, books will be sent to the Contractor for distribution. You are enrolled and ready to go when you receive your login information from [email protected].
the top of the head
For fasteners that are designed to be countersunk, the length is determined by the distance from the end of the fastener to ___.
C knots, bends, hitches
For the types of configurations in the end or joining of rope, the three general categories are ___.
False
Generally, when a nut and bolt fastener system is to be tightened a stationary backup wrench is placed on the nut and the bolt head is turned to tighten the assembly.
I understand and agree
Grading and Communication: IEC-Chesapeake Students - End of semester grades are available to employers via our AMPS database and students have access through AMPS or their online training site.
I have read and answered all questions - agree and understand
I acknowledge all aspects of the Training Policy, agree and understand that I must comply with this policy or I may be terminated from the Online Apprenticeship Program.
Yes
I am aware if I miss four weeks of lessons, instructor sessions, labs, etc., my account may become inactive.
Yes
I am aware that any homework not completed as required is an incomplete and a fail for the semester and year.
. Yes
I am aware that if I time out of my training at any point in time, I will have to pay extra to complete the training as required.
I agree
I have read and understand the syllabus in the Classroom Resource Area and all other aspects of the Classroom Resource Area.
I agree and will comply
I will attend and comply with an orientation session.
Yes
I will do my lessons according to the login informational letter and the downloadable calendar found in the classroom resource area which means completing a lesson per week.
A. I understand and agree
If you filled out an IEC-Chesapeake registration form and it refers to "SAC" - I understand the reference is to the State Apprenticeship Council (Maryland & District of Columbia). The curricula is utilized for classroom related instruction only in VA and is recognized by the Virginia Community College System (VCCS) to meet the classroom training requirements of contractors who have apprentices attending at IEC-Chesapeake.
D. all of the above
Improper torque can cause ____ A. injury and death B. fasteners to prematurely wear or break C. overheating of electrical terminals D. all of the above E. none of the above
I understand and agree
In filling out forms and/or in this related instruction, references to "BAT" means - US Department of Labor, Bureau of Apprenticeship and Training, Apprenticeship Registration.
Yes
It is my responsibility to adhere to the requirements of the online system - I will attend the instructor session each week.
Answer= D. Neither A or B A. when the pipe extension is no more than twice the length of the wrench handle and covers the handle at least ? its length. B. when the pipe extension has an inside diameter that is no more than 1/8? larger than the widest wrench handle dimension. C. Either a or b D. Neither a nor b
It is permitted to use an extension (cheater bar) on a wrench handle ___.
I understand and agree
Labs: As per the curriculum, a. Read your training guidelines, on-line and in the required student manual and student workbook to accomplish your labs. b. Labs are required to be completed before moving on to the next lesson - milestones are in place to make sure you complete each lesson before moving forward. c. Students will receive a zero for incomplete labs.
B. to cut left-turning curves
Left-cutting aviation snips are used ___.
I understand and agree
NEC Code Book: The curriculum as of 8/1/20 - 7/1/23, uses the 2020 NEC. You must have this code book to complete your assignments.
knowing how to find information in a phone book
Navigating the NEC should be similar to _______
I understand and agree
On the Job Learning (OJL) Hours: As part of the Approved Apprenticeship Program, students are required to identify their On the Job Learning hours on a monthly basis. IECC Students - It is mandatory that students enter the hours online prior to the 15th of the following month being identified. Students failing to submit their OJL forms within the time frame identified will be assessed a processing fee of $20.00 for every month their forms are late. Students are required to submit monthly OJL repots via the IEC-Chesapeake website - www.iecchesapeake.com. Pay increases for state registered apprentices will be based on satisfactory completion of both hours worked and the appropriate segment of job related education as well as performance and tardiness/absenteeism record. Non-IECC students - please comply with your IEC Chapter and/or contractor requirements. It is a good idea to keep track of all your hours as an apprentice electrician. You may end up working in a jurisdiction that will ask for your hours.
I understand and agree
On-Line Apprenticeship Training: Students placed in the on-line apprenticeship training course will be on-line for a full year. Students will not be allowed to switch to classroom in the middle of the school year. Students may be placed on-line during the year from the classroom if they have been relocated outside their classroom area. They will then have to complete the year via the on-line program and incur all additional costs. Any students transferring from a traditional brick and mortar training site to on-line at the beginning of a school session will need to purchase additional books/items that are carry over from previous year(s). Also, students will need to purchase books that were lost or destroyed.
I agree to these terms
On-line Apprenticeship Electrical Related Instruction Training is available 24 hours a day - 7 days a week.
I understand and agree
Online Apprenticeship Training Progression: On-line apprenticeship training is set up for the student to do one lesson per week. The student can do more than one lesson per week if time permits. If students do not do one lesson per week and fall behind, making it impossible to finish the semester as scheduled, an extension may be granted at a cost of $75.00for each incomplete lesson to the student.
resistance
Opposition to current flow is generally termed ________.
P
Power is represented by the letter or symbol ___.
C. either a or b A be double insulated B. have a power cord that has a grounding-type cord cap C. either a or b
Power tools should ___.
I agree and understand
Questions referring to Class enrollment Class registration Class continuation Wage progression Employer changes State Registration etc., etc., should be directed to the [email protected]
. I agree and understand.
Refund Policy: Students who are enrolled and have received their log in will not be issued a refund.
I understand and agree. No notification may be dismissal from the Electrical Online Related Instruction Training Program.
Students are REQUIRED to provide a weekly update to their employer so that progress can be tracked by the employer. This is accomplished by logging into the training site and printing your progress page.
True
Terminating the conductors in a residential meterbase requires the use of a calibrated torque tool?
constructing a building
The IEC curriculum is organized similar to _____________.
Answer = E. All of these A. installations subject to saturation of water or other liquids B. unprotected locations exposed to the weather C. directly buried cables D. raceways in direct contact with the earth E. all of these
The NEC® considers which of the following to be wet locations.
answer- E . All of these A. installations subject to saturation of water or other liquids B. unprotected locations exposed to the weather C. directly buried cables D. raceways in direct contact with the earth E. all of these
The NEC® considers which of the following to be wet locations.
I agree to attend this session on a regular basis
The REQUIRED Instructor Session is one night per week. I will attend this session on a Weekly basis - determined by the Calendar in the Classroom Resource Area. I will follow all rules and regulations as set forth by this session.
I agree to comply with this time frame
The REQUIRED Reading Worksheet is due Monday of each week.
True
The code book is something each apprentice should attempt to memorize
False
The code book is something each apprentice should attempt to memorize.
torque
The measure of rotational force is called ______.
E. Picture of folding tape
The tool shown at ___ is a folding tape.
Ohms symbol
The unit of measurement for resistance is represented by the letter or symbol ___.
ohms
The unit of measurement for resistance is represented by the letter or symbol ___.
D. should be thrown away
Tools with mushroomed striking or struck faces ___.
E. None of these A. When the pliers strike the surface at a right angle B. When the object being struck is in a vise or otherwise secured C. When safety glasses are worn D. All of these E. None of these
Under which condition listed below is it permitted to use pliers as a hammer?
Pressure
Voltage is similar to ____ in a water pipe.
pressure
Voltage is similar to ____ in a water pipe.
Work done
Wattage is often compared to ______
work done
Wattage is often compared to ______
D. Any of these
What could happen if a hammer with a loose handle is used? A. The hammer could fly off the handle and strike someone nearby. B. The hammer could slip down the handle, striking the user's hand. C. The hammer could twist and strike a surface with a glancing blow. D. Any of these E. None of these
Outlet
What is the point on a wiring system called that takes current to supply utilization equipment?
pull
When applying high torque to a wrench you should adjust your stance, to avoid falling should the wrench slip, and then __ on the wrench handle.
B. False
When using a powered drill or saw the cutting speed should be as fast as the tool will operate regardless of the material being drilled or cut.
E. I, II, & III
When using an adjustable wrench if you don't tightly adjust the jaws to the nut you could ___ .I. damage the fastener II. hurt yourself III. damage the wrench
II only
When using hammers, as a minimum, you should wear ___ I. safety glasses II. safety goggles
E. I or II or III
When using screwdrivers you should always be aware that the screwdriver blade might slip out of the slot and strike you in the ___. I. hand II. eye III. mouth
V
Which abbreviation is NOT typically associated with wattage?
E. I, II & III
Which of the following are wire connectors? I. split-bolt II. compression connector III. mechanical lug
B. I, II & III
Which of the following are wire connectors? I. wire-nut II. split-bolt III. mechanical lug
switch
Which of the following is NOT an "outlet?"
Picture III only A picture of regular safety glasses
Which of these PPEs are safety glasses?
A. 6 - 32
Which of these screws has the smallest shaft diameter? A. 6 - 32 B. 10 - 24 C. 12 - 24 D. 10 - 32 E. 8 - 32
II only
Which tools would be best to use to tighten the locknut/connector to the box? I. lineman's pliers ("kleins") and a flat-blade screwdriver II. tongue & groove pliers ("channel locks")
False
Worn or cracked sockets can be safely used if proper protective equipment is worn.
