Lesson 7: Troubleshooting Telephone Wiring and Twisted-Pair Cable

Ace your homework & exams now with Quizwiz!

If the telephone wiring is in the bus topology and the twisted-pair cable tester is connected at the embedded multimedia terminal adapter (EMTA) with the remote unit connected to the last outlet in the loop, what is the quickest way to locate the incorrectly wired outlet if the tester indicates a wiring error?

Break the loop into smaller sections and retest the two sections to identify which one has the wiring error. Continue to divide the section with the error into smaller sections until the wiring error is identified. Beginning at the EMTA end, rewire each outlet in sequence going toward the end of the loop. Keeping the loop intact, move the tester remote unit to an outlet in the middle of the loop and retest. The tester will indicate if the wiring error is back toward the EMTA, or toward the end of the loop. Beginning at the end of the loop, rewire each outlet in sequence going back to the EMTA. Break the loop into smaller sections and retest the two sections to identify which one has the wiring error. Continue to divide the section with the error into smaller sections until the wiring error is identified.

How should the digital multimeter (DMM) be used to troubleshoot problems in the telephone wiring?

Use the voltmeter function; both the network interface device (NID) and the embedded multimedia terminal adapter (EMTA) provide a steady on-hook voltage. Use the voltmeter function; both the network interface device (NID) and the embedded multimedia terminal adapter (EMTA) provide a steady on-hook voltage. Use the ohmmeter function; neither the network interface device (NID) nor the embedded multimedia terminal adapter (EMTA) provide a steady on-hook voltage. Use the voltmeter function; neither the network interface device (NID) nor the embedded multimedia terminal adapter (EMTA) provide a steady on-hook voltage. Use the ohmmeter function; both the network interface device (NID) and the embedded multimedia terminal adapter (EMTA) provide a steady on-hook voltage.

How is silver satin cable used to connect telephone equipment to wall outlets typically pinned?

Reversed at opposite ends, or cross-pinned Reversed at opposite ends, or straight-through. Identical at opposite ends, or cross-pinned. Reversed at opposite ends, or cross-pinned. Identical at opposite ends, or straight-through.

A customer reports a problem of no dial tone (NDT). Upon inspection, the technician notices that new carpeting has been installed. What should the technician do next?

Look for a cable that runs under the carpet; it is likely that the cable has a short from the carpeting tack strip. Use a telephone test set to test for dial tone at each outlet. Look for a cable that runs under the carpet; it is likely that the cable has a short from the carpeting tack strip. Use a digital multimeter (DMM) to test each circuit in the premises. Use a twisted-pair cable tester to test for dial tone at each outlet.

In unshielded twisted-pair (UTP) cable, what is the term that describes when an information-carrying conductor makes contact with a grounded conductor?

Ground fault. A short. A cross. Ground fault. A transposition.

What is the likely problem when there is dial tone on one phone connected to an outlet, but not on two other phones connected to two different outlets?

An open circuit caused by a break in a conductor, poor contact in a modular connector, or an incorrect wire connection. Reverse polarity of the tip and ring wire caused by a break in a conductor, poor contact in a modular connector, or an incorrect wire connection. A short caused by a break in a conductor, poor contact in a modular connector, or an incorrect wire connection. A ground fault caused by a break in a conductor, poor contact in a modular connector, or an incorrect wire connection. An open circuit caused by a break in a conductor, poor contact in a modular connector, or an incorrect wire connection.

What should be checked as a possible cause of hum on a customer's telephone line?

Shielding problems in the station wiring, poor terminations, or poor grounding and bonding connections. Shorts in the station wiring, poor terminations, or poor grounding and bonding connections. Opens in the station wiring, poor terminations, or poor grounding and bonding connections. Reverse polarities of the tip and ring wires in the station wiring, poor terminations, or poor grounding and bonding connections. Shielding problems in the station wiring, poor terminations, or poor grounding and bonding connections.

What is the difference between the wiring configurations for a residential, 8-position, 8-contact (8P8C) modular plug and jack in the Universal Service Order Codes (USOC) and ANSI/TIA/EIA 570-B?

The placement of pair numbers 3 and 4. The placement of pair numbers 2 and 4. The placement of pair numbers 1 and 2. The placement of pair numbers 1 and 3. The placement of pair numbers 3 and 4.

In the customer premises, what could cause some dual tone multifrequency (DTMF) touch-tone telephones to have continuous dial tone caused by polarity reversal, but not other DTMF telephones?

The telephone wiring polarity is incorrect, and the customer has a mix of older and newer DTMF touch-tone telephones. The telephone wiring polarity is incorrect, and the customer has only older models of DTMF touch-tone telephones. The customer premises is wired with a mix of unshielded twisted-pair (UTP) cable and quad station wire, and the customer has a mix of older and newer DTMF touch-tone telephones. The telephone wiring polarity is incorrect, and the customer has a mix of older and newer DTMF touch-tone telephones. The customer premises is wired with UTP cable instead of quad station wire, and the customer has only newer models of DTMF touch-tone telephones.

After resolving the problem with the premises wiring issue, which of the following is the next step in the six-step process that the technician should take?

Verify that the problem has been resolved and that phone service is running perfectly on all phones. Pack up and clean the work area of all debris. Verify that the problem has been resolved and that phone service is running perfectly on all phones. Verify that the problem has been resolved and that phone service is running perfectly on their telephone test set. Complete the paperwork to document that the problem has been resolved.


Related study sets

Unit 3: The Effect of Natural Forces on the Vehicle

View Set

Chapter 46: Management of Patients With Gastric and Duodenal Disorders 5

View Set

Computer Science Quiz [Early Computing]

View Set

Taylor ch 40 PrepU - Fluid, Electrolyte, Acid-Base Balance

View Set

Chapter 14: Musculoskeletal Imaging and Superficial Structures

View Set

Consideration & Preexisting Duty Rule

View Set

Age phisiology and school hygiene

View Set