UNEC Art. 200-215

Feeder grounded conductors shall be permitted to be sized at _____ percent of the continuous and noncontinuous load where a portion of the feeder is connected at both its supply and load ends to separately installed pressure connections.

100

At the time of installation, grounded conductors _____ AWG or larger can be identified by distinctive white or gray markings at their terminations.

4

The insulated grounded conductor(s) in a multiconductor cable _____ AWG or larger, shall be permitted to be re-identified at the time of installation at its terminations.

4

An insulated grounded conductor _____ or smaller shall be identified by a continuous white or gray outer finish, or by three continuous white or gray stripes along its entire length on other than green insulation.

6 AWG

Appliance receptacle outlets installed for a specific appliance in a dwelling unit, such as laundry equipment, shall be located within _____ of the intended location of the appliance.

6ft

The screw shell of a luminaire or lampholder shall be connected to the _____.

grounded conductor

The required heating, air-conditioning, and refrigeration equipment receptacle outlet shall be located _____ the equipment.

on the same level

For dwelling units, attached garages, and detached garages with electric power, at least _____ lighting outlet(s) controlled by a listed wall-mounted control device shall be installed to provide illumination on the exterior side of outdoor entrances or exits with grade-level access.

one

The GFCI protection required by 210.8(A) through (F) shall be _____.

readily accessible

The identification of terminals to which a neutral conductor is to be connected shall be substantially white or _____ in color.

silver

The white conductor within a cable can be used for a(an) _____ conductor where permanently reidentified to indicate its use as an ungrounded conductor at each location where the conductor is visible and accessible.

ungrounded

Feeder grounded conductors that are not connected to an overcurrent device shall be permitted to be sized at _____ percent of the continuous and noncontinuous load.

100

A meeting room with any floor dimension that is _____ ft or greater in any direction and that has a floor area of at least 215 sq ft shall have at least one floor receptacle outlet.

12

Each feeder disconnect rated 1,000A or more and installed on solidly grounded wye electrical systems of more than 150V to ground, but not exceeding _____ phase-to-phase, shall be provided with ground-fault protection of equipment in accordance with 230.95.

600v

A meeting room that is at least 12 ft wide and that has a floor area of at least 215 sq ft shall have at least one receptacle outlet located in the floor at a distance not less than _____ from any fixed wall for each 215 sq ft or major portion of floor space.

6ft

The continuity of a grounded conductor shall not depend on a connection to _____.

All of these (a metallic enclosure, a raceway, cable armor)

_____ conductors shall not be used for more than one branch circuit, one multiwire branch circuit, or more than one set of ungrounded feeder conductors except as allowed elsewhere in the Code.

Neutral

At least one lighting outlet controlled by a listed wall-mounted control device shall be installed in every habitable room, kitchen, and bathroom of a dwelling unit.

True

Article 200 provides the requirements for _____.

all of these( identification of terminals, grounded conductors in premises wiring systems, identification of grounded conductors)

Where a premises wiring system contains feeders supplied from more than one nominal voltage system, each ungrounded conductor of a feeder shall be identified by phase or line and system by _____, or other approved means.

any of these ( color coding, marking tape, tagging)

In a dwelling unit, illumination for outdoor entrances that have grade-level access can be controlled by _____ control.

any of these( remote, central, automatic)

Where a portion of a feeder is connected at both its supply and load ends to separately installed pressure connections in accordance with 110.14(C)(2), it shall be permitted to have an allowable ampacity _____ the sum of the continuous load plus the noncontinuous load.

not less than

In dwelling units, when determining the spacing of receptacle outlets, _____ on exterior walls shall not be considered wall space.

sliding panels

Where equipment, other than service equipment, requires dedicated equipment space as specified in 110.26(E), the required receptacle outlet shall be located within _____ the electrical equipment.

the same room or area as

Receptacles shall have the terminal intended for connection to the grounded conductor identified by a metal or metal coating that is substantially white or silver in color or by the word "_____."

white