Windows
What are the characteristics of RAID 4?
RAID 4 consists of block-level striping with a dedicated parity disk. As a result of its layout, RAID 4 provides good performance of random reads, while the performance of random writes is low due to the need to write all parity data to a single disk.[20] In diagram 1, a read request for block A1 would be serviced by disk 0. A simultaneous read request for block B1 would have to wait, but a read request for B2 could be serviced concurrently by disk 1.
What are the characteristics of RAID 10?
RAID 10, also known as RAID 1+0, is a RAID configuration that combines disk mirroring and disk striping to protect data. It requires a minimum of four disks and stripes data across mirrored pairs. As long as one disk in each mirrored pair is functional, data can be retrieved.
What are the characteristics of RAID 100?
RAID 100, sometimes also called RAID 10+0, is a stripe of RAID 10s. This is logically equivalent to a wider RAID 10 array, but is generally implemented using software RAID 0 over hardware RAID 10. Being "striped two ways", RAID 100 is described as a "plaid RAID".
What is a parity drive?
A parity drive to create a system that is both fault tolerant and, because of data striping, fast.[1] Basically, a single data bit is added to the end of a data block to ensure the number of bits in the message is either odd or even. One way to implement a parity drive in a RAID array is to use the exclusive or (XOR) function. XOR is a Boolean logic function which means 'one or the other, but not both'. The XOR of all of the data drives in the RAID array is written to the parity drive. If one of the data drives fails, the XOR of the remaining drives is identical to the data of the lost drive. Therefore, when a drive is lost, recovering the drive is as simple as copying the XOR of the remaining drives to a fresh data drive.
How are Linux servers typically managed
Linux servers are usually remotely managed using SSH.
What is RAID 0?
RAID 0 (also known as a stripe set or striped volume) splits ("stripes") data evenly across two or more disks, without parity information, redundancy, or fault tolerance. Since RAID 0 provides no fault tolerance or redundancy, the failure of one drive will cause the entire array to fail; as a result of having data striped across all disks, the failure will result in total data loss. This configuration is typically implemented having speed as the intended goal.
Describe RAID 1.
RAID 1 consists of an exact copy (or mirror) of a set of data on two or more disks; a classic RAID 1 mirrored pair contains two disks. This configuration offers no parity, striping, or spanning of disk space across multiple disks, since the data is mirrored on all disks belonging to the array, and the array can only be as big as the smallest member disk. This layout is useful when read performance or reliability is more important than write performance or the resulting data storage capacity. The array will continue to operate so long as at least one member drive is operational.
What are the characteristics of RAID 5?
RAID 5 consists of block-level striping with distributed parity. Unlike in RAID 4, parity information is distributed among the drives. It requires that all drives but one be present to operate. Upon failure of a single drive, subsequent reads can be calculated from the distributed parity such that no data is lost. RAID 5 requires at least three disks.
What are the characteristics of RAID 50?
RAID 50, also known as RAID 5+0, combines distributed parity (RAID 5) with striping (RAID 0). It requires a minimum of six drives. This RAID level offers better write performance, increased data protection and faster rebuilds than RAID 5
What are the characteristics of RAID 6?
RAID 6 extends RAID 5 by adding another parity block; thus, it uses block-level striping with two parity blocks distributed across all member disks. According to the Storage Networking Industry Association (SNIA), the definition of RAID 6 is: "Any form of RAID that can continue to execute read and write requests to all of a RAID array's virtual disks in the presence of any two concurrent disk failures. Several methods, including dual check data computations (parity and Reed-Solomon), orthogonal dual parity check data and diagonal parity, have been used to implement RAID Level 6.
What are the characteristics of RAID 60?
RAID 60, also called RAID 6+0, combines the straight block-level striping of RAID 0 with the distributed double parity of RAID 6, resulting in a RAID 0 array striped across RAID 6 elements. It requires at least eight disks.
What's a difference in memory cards for servers vs desktops
Servers use error code correcting (ECC) RAM. Whereas non-server desktops don't.
What is data striping?
Data striping is the technique of segmenting logically sequential data, such as a file, so that consecutive segments are stored on different physical storage devices. Striping is useful when a processing device requests data more quickly than a single storage device can provide it.
What is Group Policy?
Group Policy is an infrastructure that allows you to specify managed configurations for users and computers through Group Policy settings and Group Policy Preferences. To configure Group Policy settings that affect only a local computer or user, you can use the Local Group Policy Editor. You can manage Group Policy settings and Group Policy Preferences in an Active Directory Domain Services (AD DS) environment through the Group Policy Management Console (GPMC). Group Policy management tools also are included in the Remote Server Administration Tools pack to provide a way for you to administer Group Policy settings from your desktop. Windows PowerShell When the GPMC is installed on servers or client computers, the Windows PowerShell module is also installed. You have full Windows PowerShell functionality. If you install the Remote Server Administration Tools pack, the latest Windows PowerShell cmdlets for Group Policy are also installed. For more information about Windows PowerShell cmdlets and scripts that you can use to manage Group Policy, see Group Policy Cmdlets.