1S051 Safety CDCs

¡Supera tus tareas y exámenes ahora con Quizwiz!

Class C, D, and E

A Single Investigation Officer would investigate what type of mishaps?

braces of 1 by 8 inches on both the front and rear sides

A bricklayer's square scaffold must have

Basic plan, table of contents, and annexes

A contingency plan contains which parts?

aircraft parking areas.

A cryogenic liquid oxygen (LOX} storage tank of more than 100 gallons must be at least 75 feet from

Cause

A deficiency which if corrected, eliminated, or avoided, would likely have prevented or mitigated the mishap damage or significant injuries is a

approved by the site supervisor

A fire or open flame'device can be used during construction activities only when

1/4 inch in 12 inches.

A hoisting chain must be removed from service when it has elongated more than

30 percent

A loader can be safely operated on a straight slope up to

restore, sustain,and modernize mission compliance at each installation

A primary objective of the Environment, Safety,and Occupational Health Compliance Assessment and Management Program (ESOHCAMP) is to

Job Safety Analysis

A procedure used by supervisors and employees to assess the hazards associated with a work procedure and determine the safest and most efficient means of doing a given task best defines

evaluate the exposure potential of a system that emits RFR against the permissible exposure limit.

A radio frequency radiation (RFR) safety program should

4,000 pounds

A safety belt and harness assembly must be capable of withstanding a tensile load of at least

75

A service cart must be at least how many feet away from a fueling operation?

180

A supplier may not end or reduce support without giving the receiver written notice within how many days?

very high

A toxic gas and vapor concentration of three percent is considered

a hazard report identifies an intersection with a high number of accidents

A traffic engineering study would be useful when

enlarge cored holes

A twist drill bit with four flutes should only be used to

15

Acetylene must not be used at pressures exceeding how many pounds per square inch (psi)?

air purged

After fuel residues have been removed through depuddling, fuel cells must be

5

After turning, the aircraft must be marshaled forward in a straight line at least how many feet to relieve the loads on the main landing gear?

Air Force Office of Special Investigations agents performing protective services.

All Air Force personnel must wear seatbelts at all times with the exception of

12 months

All members of confined-space rescue teams must have hands-on training in removing victims at least every

50 inches or less

An all-terrain vehicle is a three- or four-wheeled vehicle that has low pressure tires and a wheel base of

Operational Hazard Analysis

An analysis of the detailed procedures of an operation and how a deviation from these procedures could lead to a hazard defines

severity

An assessment of the expected consequences if a hazard results in a mishap is called

23.5 percent

An atmosphere is considered oxygen-enriched when oxygen content rises above

Commander

An effective awards program depends on the involvement of whom?

good intra-office discipline.

An effective mishap prevention program begins with

a positive electrode, negative electrode, and an electrolyte

An electrical cell consists of

6

An electrical outlet must be protected by a ground fault circuit interrupter (GFCI) when it is located within how many feet of a sink?

return wire attached to a ground in the earth.

An example of a system ground is a

when an electronics component tray is removed from its rack, releasing a button

An interlock interrupts circuit flow

mechanical ventilation

Any type of fan device that aids the flow of air in an area is known as

30

Approximately how many days prior to opening day must a pre-season inspection of the swimming pool be conducted?

25

As a general rule, wing walkers must be used when an aircraft is taxied within how many feet of an obstruction?

protecting government property and personnel

As a safety representative,your main concern with regard to contract surveillance involves

8 inches

At least how high must barriers or curbing be at the edges of excavations to protect vehicles that are loading and unloading?

At least 10 feet.

At least how long is a sufficient length of hose between the clip-on chuck and the in-line valve to allow the employee to stand outside the trajectory of an airline hose?

Two

At least how many people must be present when conducting live-fire operations?

brought before formal public hearings

Before the creation or revision of an Occupational Safety and Health Act safety standard, the standard must be

10 feet

Before the operator of a chain saw starts the engine, how far must the chain saw be from the fueling point?

Four

Bleacher seating must have guardrails if it is at least how many feet from the ground?

10.

Booms on construction equipment must be at least how many feet from overhead high voltage power lines?

Avoidance

Canceling a mission altogether is employing which risk control option?

alkyl lead compounds

Color is added to aviation and motor gasolines to indicate the presence of

4

Duckboards used in trailer and railcar loading and unloading should be capable of holding how many times its expected load?

nitrogen gas

Due to weight and speed of modern aircraft, the tires are often inflated with

refer the facility manager to fire prevention personnel

During an inspection,if you believe that the facility does not have an adequate number of fire extinguishers, you should

Site assessment activities

During which Environment, Safety, and Occupational Health Compliance Assessment and Management Program assessment activity does the team conduct record searches, interviews, and site surveys to determine the compliance of the installation to comply with regulations and instructions?

Post-assessment

During which Environment, Safety,and Occupational Health Compliance Assessment and Management Program assessment activity does the MAJCOM follow up on site activities?

explosion proof

Electrical equipment and fixtures in paint and dope areas must always be

6 months

Electrical resistance gloves that are in active use must be dielectric tested every

16 inches long

Emergency equipment required for high voltage areas must include rope that is 1/2-inch hemp and at least

Five

Energized circuits located within how many feet of emergency showers must be protected by a ground fault circuit interrupter?

six feet

Except in established storage areas, stacks of lumber at construction sites should not be higher than

every three years

External Environment, Safety, and Occupational Health Compliance Assessment and Management Program assessments are conducted at least

6 feet

Fall protection must be used during construction operations at a height of at least

45 degrees

Fighter aircraft must be parked at an angle of at least

Annually or whenever modified tasks affect exposure

For a shop where workers are exposed to bloodborne pathogens, when must the exposure control plan be reviewed and updated?

When studying or researching for an inspection

For best results, when should you prepare a safety inspection checklist?

Appropriate Air Staff agency

For hazard reports that involve military unique operations or equipment, what is the highest review level in the appeal process?

encasing the entire tool in a nonconductive material

For small-capacity electrical tools, double insulation can be provided by

Space

For which mishap is a promise of confidentiality authorized?

200

Generally people and vehicles should not pass closer than how many feet to the rear of an aircraft with its engines running?

there are no breaks in the grounding path

Grounding is effective when

both dynamic and static electrical charges

Grounding is used to control

sanitizing the report

Hiding the relationship between the identity of a mishap and the findings,causes, and recommendationsis called

10

Horizontal sliding hangar doors must be opened wide enough to permit clearance of at least how many feet at each wing tip?

By direct total dollar cost of damage and degree of injury/illness

How does the Air Force classify mishaps?

Three feet.

How far above a platform or landing must a portable ladder extend?

18 inches.

How far above the floor of aircraft hangars must spark-producing components be located when a hydraulic jack pumping unit is being used inside a hangar?

Prior to each use

How frequent are sling inspections done?

Milliamperes

How is electrical current measured when you want to describe its effect on the human body?

10 days

How long after a Class A mishap occurs must the status message be sent?

Until the hazard is corrected or for three days, whichever is longer.

How long must a notice of hazard remain posted?

30 minutes

How long must a worker wait after receiving fuel to manually gauge or measure a fuel tank?

11

How many months is the formulation stage of the budget cycle?

Two

How many parts does a privileged formal safety report contain?

six

How many steps are in the operational risk management

1 milliampere

How much current causes a normally harmless shock to be felt?

12 months.

How much time are safety students normally allotted to complete a career development course (CDC)?

Triennially

How often are support agreements reviewed for other than budgetary considerations?

Annually

How often is the Career Field Education and Training Plan (CFETP) reviewed to validate currency?

Annually

How often must barricades be inspected to determine the degree of settling erosion?

Daily

How often must cables and sheaves on cranes be inspected for defects?

12 months

How often must ground handling personnel be tested for proficiency on movement of aircraft?

Annually

How often must the safety staff evaluate a lockout/tagout program to ensure the requirements of the program are being followed?

After each meal period

How often should hood filters over a grill be washed?

On a continuous rotating basis

How often will the Air Force Safety Center conduct a staff assistance visit on a MAJCOM?

Executive Orders

How were federal agencies required to follow the Occupational Safety and Health Act?

50 feet

How wide must a firebreak be around a potential explosives site (PES)?

self-adjusting

If a machine guard opens when stock is moved into the danger area and returns to a rest position when the stock is removed, that guard is

90

If a magazine's earth cover erodes to less than two feet, repair it as soon as practical or within how many days?

cracked skin, severe burns, or blood poisoning

If a worker spills hydrocarbon fuels on the skin, he or she may experience

Report them to the fire prevention personnel at the fire department for action.

If during an annual inspection of the child development center you identify and document several fire deficiencies, what should be your next course of action?

85 decibels averaged over an eight-hour period

If you were working in a machine shop, your workplace would be designated as a hazardous noise environment when the noise in the shop equals or exceeds

the commander of the Military Traffic Management Command.

If your base has no traffic engineer,the installation commander may request assistance from

Chemical plants

In 1924, the first respirator appeared in what industry?

36

In a machine shop, how many inches wide should aisles be to permit free movement of workers and equipment?

Pour acid slowly into water

In battery shop operations, how should sulfuric acid and water be mixed together?

Red and green

In color coding, black lettering should not be used on which background(s)?

Civil

In construction drawing plans for blueprints, in which category are utilities and grading plans usually included?

Relays

In electrical work, what is generally used to control large, high-voltage currents with a low-voltage, low-current signal?

Where employees do not have to touch metal equipment to reach them

In food preparation areas, where should electrical switches for equipment be located?

made of wood.

In meat market storage areas, sawdust may be used on floors

have an effective training program in place

In reference to the supervisory roles in training, one of the best ways a supervisor can improve productivity and esprit de corps is to

dislike rules and regulations

In relation to human factors in the mishap prevention program, people who can be expected to generally dislike safety rules and regulations are those who

as long as the attitudes serve and satisfy their needs

In relation to human factors in the mishap prevention program, people's attitudes may be expected to remain unchanged

mishap areas that should be analyzed further

In the analysis process, the use of statistical charts and graphs is helpful in determining

conducts follow-up inspections to ensure program compliance

In the hearing conservation program, the safety professional

Raw mishap numbers

In what analysis limitation is exposure not considered when collecting the information?

The aircraft is also rearmed

In what respect does the combat turnaround operation differ from hot-pit refueling?

Rotating.

In-running nip points are a specific danger of which type of motion?

privileged

Information that is exempt by statute or case law from being released outside the Air Force community is known as

isolation

Installing a guard or barrier between the worker and the hazardous operation illustrates the hazard control method of

annually

Internal Environment,Safety, and Occupational Health Compliance Assessment and Management Program assessments are conducted at least

the equipment is moved about so much

It is hard to maintain an effective ground for portable electric equipment because

5000 lbs

Lanyards, D-rings, locking snap-hooks, and all components of a fall arrest system must be capable of sustaining a minimum tensile load of

activities that have jerky throwing motions

Lateral epicondylitis, or tennis elbow, is caused by

-297°F

Liquid oxygen (LOX) is stored at what temperature?

tips

Maintenance on soldering irons and guns is primarily centered on the

50

Maintenance work on other aircraft is restricted within how many feet of aircraft fueling operations?

a comprehensive and cohesive training program is available for each person in the specialty

Major command functional managers and supervisors at all levels use the Career Field Education and Training Plan (CFETP) to make sure that

Four

Mishap probability has how many categories?

ground and industrial - sports and recreation.

Mishaps involving injuries that occur during participation in some form of duty related athletic or recreational sport activity is categorized as

the interview is formal

Multiple interviewers can be intimidating and generally should not be used except for when

Self-rescue, centrally located rescue team, and organizational rescue team

Name the three primary means of rescue from confined spaces.

USAF surgeon general.

Noise exposure limits are established by the

3 1/2.

On a powder-actuated hand tool, the steel muzzle guard must be at least how many inches in diameter to protect personnel from flying particles?

must be securely anchored against the shank of the drill bit

On an electric drill,the chuck

to within three inches of the building wall

On an outrigger scaffold, planking must be laid tight and extended

the same point as the lock

On machinery, tagout devices used with energy isolating (lockout) devices should be attached at

Weight of the evidence, Professional knowledge, Investigator's best judgment

On what do you base mishap findings?

10

Once a non-imminent danger hazard report is received,it must be acted upon within how many days?

Commander and safety staff of the organization evaluated

Once a report of a safety program evaluation is written, to whom is it sent?

witness' memories degrade as time passes

Once you set up a time and date for the interview, it is important to avoid postponements because

two alternations of current (one in one direction and one in the other)

One complete cycle of alternating current (AC) is composed of

Wing, base, and squadron

Operational plans are most often written at what level{s)?

Transference

Opting to send an unmanned drone instead of a manned aircraft into a hostile fire environment is employing which risk control option?

19.5 percent

Oxygen deficiency is first reached when oxygen content is below

30

Personnel must be tested within how many days of being assigned to duties requiring their knowledge of marshaling signals?

positioned well back from the sidelines

Playing field bleachers must always be

propellant oxidizers

Proper handling of hydrocarbon fuels eliminates any possibility of them being spilled in the same area as

locations where the permissible exposure limit can be exceeded .

Refresher training for the radio frequency radiation awareness program will include all of the following except

have their own air supply

Regarding air flow within ventilation systems, laboratory hood exhaust systems should

Range control officer (RCO).

Regardless of the class of range, who has overall control over safety on the weapons range?

6 strands with 19 wires

Regular hoisting rope is made up of

opposes or restricts the flow of electricity

Resistance is any condition that

12 months

Rubber insulating gloves in storage must be dielectric tested every

500 pounds

Rungs on ladders must be strong enough to support at least

Two types, three classes

Safety helmets can be broken down into how many types and classes?

Provide complete protection against airborne toxicity and oxygen deficiency.

Self-contained breathing apparatus respirators

first-aid kits, repair kits, and emergency lights

Self-propelled construction equipment must be equipped with

Wing Commander

Site planning is based on the recommendation of the Facility Utilization Board (FUB) and approved by

Three

Space mishaps are divided into how many subcategories?

12

Storage magazines must have reinforced concrete walls that are no less than how many inches thick?

third workday of each month

Tenant units will provide the host safety office a summary of civilian and military occupational injuries/illnesses data by the

Air Force Special Operations Command.

The Air Force Manpower Standard 106A applies to

1 February; 30 April

The OSHA 300A, Summary of Work-Related Injuries and Illnesses, report must be posted not later than when and remain in place until what date?

Department of Labor

The Occupation Safety and Health Administration (OSHA) and Bureau of Labor Statistics (BLS) are organizations within which agency?

work places would be safe and healthful

The Occupational Safety and Health Act (OSHA) of 1970 was passed to ensure that

Private industry

The Occupational Safety and Health Act of 1970 applied mainly to which industries/agencies?

cost effectiveness index.

The abatement priority number (APN)is a code consisting of the risk assessment code (RAC) and the

follow-up action

The action taken to make certain that reported discrepancies have been or are being corrected is called

the purpose for which the location is used

The amount of light to be provided in a given location is based on

Man, media, machine, and management

The basic cause factors of mishaps fall into which categories as the contributors to successful missions?

where the witness was during the mishap

The best location to conduct an interview is

Target, monitor, and study

The best way to approach analysis is to divide it up into what three functions?

obtain lasting corrective action

The desired result of recommendations stemming from any analysis program is to

addressed to an action agency

The end result of an analysis is useless unless the recommended action is

installation civil engineer

The floor loading capacity of a machine shop is determined by the

water running through a pipe

The flow of electricity may be compared to

Accepting risks at the appropriate level to preserve mission accomplishment

The goals of operational risk management (ORM) include all of the following except

personnel and time

The ground safety manager must schedule inspections to make the most effective use of

rubber gloves, aprons, and face shields or chemical goggles

The handling of caustic solutions in liquid oxygen (LOX) plant operations requires the use of

provide technical support and consultation to commanders .

The main reason safety responds to all major accidents and disaster sites is to

5 mph

The maximum speed for a vehicle operated within 10 feet of an aircraft is

5 mph

The maximum speed that any aircraft may be towed at any time is

5 mph

The maximum speed that any two maintenance stands may be towed over a smooth, paved surface is

10 seconds and 100 feet

The maximum time and distance between hazardous operations or materials and an emergency shower and eyewash unit are

full face shield

The most appropriate eye protection device for pressurized spray painting is a

The material deficiency and reporting program

The most practical way of establishing an initial mishap notification system is

quantity of fuel needed and the time required to refuel the aircraft.

The number of refueling vehicles required to service an aircraft at any one time is determined by the

10

The office of primary responsibility (OPR) for a hazard report must return the report with action annotated to the safety office within how many work days?

amount of the current flow

The primary factor influencing the severity of electrical shock to the human body is the

your findings and recommendations.

The purpose of an outbriefing after an inspection is to discuss

Exterior hood

The push-pull system is an example of which local exhaust ventilation system?

10 gallons

The quantity of fuel permitted in a test laboratory is limited to

feasible and effective

The recommendations in a mishap report should be both

provide guidance for safety reporting, assign mishap prevention responsibilities, and specify chain of command

The safety annex to contingency plans must

all hazardous machinery be safeguarded.

The safety law passed by the state of Massachusetts in 1867 required that

findings and causes

The second part of an inspection report contains

four feet deep

The sides of excavations in loose dirt must be braced and shored if the excavations are more than

mitigating the risks involved with completing the task

The steps of conducting a job safety analysis (JSA) includes all of the following except

corrective actions

The third part of an inspection report contains

faultfinding

To be effective,safety inspections must be all of the following except

to permit an even flow of materials

To ensure proper layout, equipment and machinery must be arranged

engineer hazards out

To prevent mishaps involving machinery, the best action, which should be pursued first, is to

four inches high

Toeboards placed on scaffolds must be at least

receiver's needs and the supplier's ability to meet those needs

Ultimately, the support agreement is a negotiated contract based on

25 ohms.

Under dry conditions, electrode resistance to ground should not exceed

15 mph

Under normal circumstances general purpose vehicles may not exceed what speed when operating on the flight line?

The employer

Under the Occupational Safety and Health Act, who is accountable for employee violations of safety and health standards?

Annually

Unless otherwise directed, how often will workplaces and operations be inspected

separators.

Vehicle maintenance shop floor drains must be equipped with

Three

Vehicle mishaps are divided into how many subcategories?

8 hours of formal training in using the equipment

Warehouse workers who wear respiratory equipment due to handling chemical or toxic supplies require at least

90

Weapons safety managers (WSM) must complete the weapons safety course within how many days of appointment?

1118

What AF Form is used to identify the existence of a hazardous condition that could result in death, disability, or a lost-workday mishap?

979

What AF form is used to temporarily identify a hazardous condition?

Specialty Training Standard

What Air Force publication serves as a formal contract between Air Education Training Command and the functional user to show which of the overall training requirements for an Air Force specialty code are taught in formal schools and correspondence courses?

Veto the bill and return it to Congress with a message stating why it is objectionable

What action may the president take once Congress sends the appropriation bill?

Giving the trainee a pre-test

What action serves as an invaluable tool when assessing what the trainee already knows?

HQ AFSC

What agency prepares of the Memorandum of Final Evaluation for on-duty Class A and B formal ground mishap reports?

Bioenvironmental engineering

What agency reviews the initial design for any ventilation system to be used in Air Force environments?

Rates

What analysis limitation should not be used as the sole basis for determining the success of prevention efforts?

Interim control measures

What are temporary measures taken to reduce the degree of risk associated with an occupational hazard or deficiency pending completion of an abatement program?

Mishap reports

What are the basic source documents used to analyze mishap experience?

Not less than 2 inches and no more than 6 inches above the surface

What are the minimum and maximum height limitations for the forks of a travel ing forklift?

Six months upgrade training, completion of minimum core training tasks, and recommendation by supervisor

What are the prerequisites for a 7-level upgrade trainee to attend the craftsman resident course?

Severity and probability

What are the two criteria used in determining the priority with which a hazard should be abated?

Protect the health of the worker and reduce the fire and explosion hazard

What are the two main purposes of a spray booth?

Crowd control and souvenir hunting

What are two common hazards associated with weapons ranges?

Using the wrong kind of screwdriver for the task

What common behavior creates safety hazards when using screwdrivers?

Effectiveness of wartime plans

What do peacetime deployments test?

Base traffic circulation plan

What document describes the safest and most efficient way to use primary and secondary roads on an installation?

Small amounts of data result in large changes.

What effect does the limited availability of data have on the analysis function?

Fuel, heat, oxygen, and chemical reaction

What elements must be present in order for a fire to start?

Plows

What equipment is used to break up unimproved ground?

Set of the teeth

What factor controls the "binding" of hacksaw blades?

Budgetary constraints

What factor has forced a reduction in the number of general workplace safety inspections?

Spring-tooth

What harrow would likely be used to mix and stir soils during stabilization?

Spike-tooth

What harrow would most likely be used to smooth soil on a softball field?

The worker may be struck or caught in a pinch by the moving part

What hazard is commonly associated with a transverse motion?

Identification of activity,checklist items, and notation of reference material.

What informationis contained in Air Force Occupational Safety and Health (AFOSH) standard checklists?

Carbon

What ingredient present in most solvents makes them organic?

Perform a restraint usage survey before and after the program

What is a good way to gauge the impact of your restraint awareness program?

A device that communicates the information in a signal to another device.

What is a relay?

Probability.

What is an assessment of the likelihood that a hazard or deficiency will result in a mishap?

Operator 1 (01,AFSAS Person 2)

What is an example of the correct way to identify a person for the first time in a narrative?

Distributing appropriated dollars

What is apportionment as it applies to the third stage of the budget cycle?

Training

What is considered one of the best investments any safety office can make?

Financial plan

What is known as a financial blueprint for a specific period of time?

Distance learning courses

What is one of the more common ways to provide training and save money?

Create a mishap database

What is one of the most common uses of the computer in an analysis program?

The budget cycle.

What is referred to as the time phasing of pricing out and funding of the various programs?

Dozer

What is the best vehicle for clearing the sides of sloping land?

Early education in risk management principles and tools

What is the cornerstone of the operational risk management (ORM) program?

Associates degreegrade.

What is the desired education level for a safety craftsman?

Grounding

What is the easiest way to protect the operator of an electrically powered hand tool?

Ensure the handle is properly pinned and sealed

What is the first step when inspecting a flightline fire extinguisher?

Initial symptoms of poisoning are slight but become severe later on

What is the hidden danger in the fumes of nitric acid?

Secretary of the Air Force Award

What is the highest safety award in the Air Force given to the MAJCOM,DRU, or FOA with the most effective safety program?

The cab is stationary

What is the main disadvantage of using the mobile hydraulic crane?

120

What is the maximum number of gallons of Class I flammable liquids that may be stored in a storage cabinet at one time?

170°F

What is the maximum temperature for hot-pack machines in medical facilities?

2 feet wider than the widest vehicle used

What is the minimum allowable width of the aisles in a storage warehouse?

36 inches

What is the minimum clearance between a monorail and any obstruction?

Two feet

What is the minimum distance a strip of insulating matting must extend past each end of a work area?

25-50 feet

What is the minimum wing tip clearance for aircraft with wingspans greater than 110 feet?

Written tests

What is the most appropriate means used to measure knowledge-oriented objectives?

Kinetic

What is the most widely used and taught method of lifting?

To reduce the hazards and risk to personnel to an acceptable level while continuing to execute the required missions successfully

What is the overall goal of risk management?

To ensure that there is a need for training and to identify the nature of the content of the training program

What is the primary purpose of the training needs assessment?

To encourage open and frank communication with the witnesses.

What is the purpose of giving a witness a promise of confidentiality during a mishap investigation?

Equalization of static charges that may be generated

What is the purpose of placing bonding wire between two metal objects?

5 mph

What is the speed limit for forklifts inside of warehouses?

150 feet

What is the towing distance in between aircraft if the trailing aircraft has faulty brakes?

Standardized Air Force tracking system

What is used to track hazardous material (HAZMAT) purchases?

Directing the analysis at local problems for which functional managers have control

What makes a mishap prevention analysis program effective?

18 inches

What minimum distance must be maintained between a heat producing appliance and combustibles?

C

What mishap class requires a preliminary message report within six days after the mishap?

How the replacement promotes efficiency in time, manpower, money, and productivity

What must equipment justification describe?

Severity

What operation risk management (ORM) term describes the expected consequences of an event in terms of mission impact, injury,and property damage?

80 to 90 percent

What percentage of mishap causal factors is contributed to human error?

20.

What percentage of unmanned missile launch facilities must be inspected at least once a year?

It can freeze human tissue

What physiological danger does liquid oxygen (LOX) present to personnel?

Goggles

What piece of personal protective equipment (PPE) must personnel working on hydraulic systems wear?

The material deficiency and reporting program

What program (used for investigative analysis) was developed in order to ensure that everyone in the Air Force receives material and equipment which is of the highest quality and which will serve its intended purpose to the fullest extent?

Issues government-owned HAZMAT

What role does HAZMART play in the installation hazardous material management program (IHMP)?

Continue to ask "Why?" until you come to a dead end

What rule of thumb should you use to make sure you have identified the root causes of a mishap?

Personal protective equipment

What solution is a last resort for controlling exposure to hazards?

Execution.

What stage encompasses the distribution and administration of funds?

Mishap investigation kit.

What tool should every safety office have when responding to a mishap?

Program management and facilities

What two types of checklists should be available for a safety inspection?

Construction

What type of contract is used to modify existing facilities?

Gantry

What type of crane has a trolley that is rigidly supported on two or more legs running on fixed rails?

Storage cell

What type of electrical cell can be restored to a charged condition by passing an electrical current through the cell in the opposite direction of the discharging current?

Vaulted (self-diking)

What type of fuel storage tank can be located next to buildings?

Underground

What type of fuel storage tanks are used to store gasoline at base service stations?

Rubber apron

What type of personal protective equipment (PPE) must be worn in water treatment laboratories when handling acids?

Eye protection only

What type of protection is mandatory when playing racquetball?

Water proof apron and rubber gloves

What type of protective equipment should be provided for workers in the pots and pans area?

Open ended.

What type of questions should you ask to start an interview?

Amperes

What unit of measurement is used to measure electrical current?

A project book

What usually precedes the final specifications/blueprints to give base agencies a detailed explanation of construction?

25 feet.

When a hydraulic jack pumping unit is being used inside a hangar, what is the minimum distance that must be maintained between the pumping unit and the aircraft?

The Air Force at large

When a mishap occurs involving a foreign exchange student, what agency is held accountable?

Isolate the procedure or equipment from personnel

When a procedure or piece of equipment exceeds the limits of safe noise exposure, what is the best course of action?

50 lbs

When a tag is used during the lockout/tagout procedure, it must have a minimum unlocking strength of at least

16 inches apart

When a worker doing floor removal must straddle two planks, the planks must be no more than

foreign object damage

When an aircraft engine is being serviced in the shop, all openings should be covered to prevent

degreasing.

When an engine is received in the shop after it is removed from an aircraft on the flight line, it probably requires

90

When an individual is appointed as a flight safety noncommissioned officer (FSNCO), they must have completed or be scheduled to attend the FSNCO course within how many days of assignment?

The objective

When conducting an evaluation of a new trainee, what is the first thing you should determine?

is performing tasks above and beyond those found on the process analysis survey

When determining the manpower needed for the base safety office, you can submit a variance request to the Air Force Manpower Standard 106A when the safety office

After release of the final message

When do follow-up actions start for mishap reports?

three feet

When electrical parts are exposed, the workspace clearance must have a radius of at least

an electrical cell

When electrical pressure is generated by chemical action, the device in which this occurs is called

vapors exceed the threshold limit value

When handling fuming nitric acids, respiratory protection is required whenever the

25.

When ladders are required in trenches, they should be placed so that workers must travel no more than how many feet in any direction to reach an exit?

One

When ladders are used during aerial work, how many people may ascend or descend the structure at any one time?

that causes the tracks of the equipment to leave the ground

When lifting loads with heavy equipment, the operator must avoid raising any load

695 times its original volume.

When liquid nitrogen is converted to gas, it expands to

10

When material handling equipment (MHE) is stored in magazines and warehouses there must be at least how many feet between any combustible material and the equipment?

When additional help is present and the safety guard is equipped with the prescribed respiratory equipment

When may a safety guard enter a tank in an attempt to rescue someone?

Air Force Records and Distribution Schedule

When mishap reports are no longer needed, dispose of them IAW with

containers or on racks

When not in use, meat hooks should be stored in

150 pounds

When removing materials from a demolition site, what is the maximum weight for any object being dropped through a chute?

Promptly

When should you arrange a personal interview with a witness?

command yardsticks

When tabulating statistics and determining mishap areas to be explored, the use of historical data is necessary to establish

2

When tag lines are used in materials handling, they should be how many times as long as the height of the crate they are being used on?

year

When there are no changes in procedures, process, or systems associated with the lockout/tagout program, retraining must take place at least every

six inches

When using a meat slicer to slice meat, a pusher plate is required once the meat becomes shorter than

Apply only light pressure

When using a portable sander, what should be done to protect the motor from overheating?

Failure to use a handle

When using files, what action frequently leads to puncture wounds?

75 feet.

When wearing a hose mask respirator without a blower unit (Type B),what is the maximum distance beyond uncontaminated air that a worker may go?

During the enactment

When will Air Force personnel make presentations for budgeting?

Conduct a familiarization walk through.

When you areinvestigating a mishap,what is the first thing you should do once you are allowed into the mishap site?

National Electric Code (NEC).

Where can you find the standard for Air Force electrical systems and operations?

Three.

Where explosives are concerned,the National Electric Code (NEC) places hazardous locations into how many classes?

Even with the nose of the aircraft and at a 45 degree angle outboard of the engine

Where is the fireguard positioned during an engine start?

50 feet.

Where security fences are not provided, how far from the diked areas of underground fuel storage tanks must danger signs be posted?

six months

Whether in use or not, belts, lanyards, and lifelines must be inspected atleast every

101 Critical Days of Summer

Which Air Force-wide campaign has run annually since the early 1980s?

Waiver

Which action is defined as a written authority for a specific short-term departure from a mandatory quantity distance (QD) requirement?

HQ AFSC and MAJCOMs.

Which agencies may direct preparation of a formal report for any mishap?

Bioenvironmental engineering.

Which agency assists unit commanders and shop supervisors with the development of radio frequency radiation training awareness programs?

HQ USAF/SE.

Which agency can approve the release of privileged information outside the Air Force?

HQ USAF/SE.

Which agency determines accountability when multiple MAJCOMs have assets involved in a mishap and cannot reach an agreement as to who is accountable?

Air Force Safety Center.

Which agency establishes inspection standards for radio frequency radiation safety programs?

The unit

Which agency is responsible for providing initial and annual refresher radio frequency radiation training?

MAJCOMs

Which agency or individual manages and tracks training for all safety personnel through the use of a computer database program?

Defense Contract Management Agency.

Which agency or office performs the pre-award survey?

Financial Analysis Office

Which agency prepares the financial plan and submits it to the MAJCOM?

OSHA.

Which agency requires higher headquarters to evaluate the safety program management of organizations at or above wing level?

Safety, civil engineering, and public health

Which base agencies perform a pre- and post-season inspection of the softball fields?

Civil Egineering.

Which base agency leads the hazardous material management process (HMMP) team?

Bioenvironmental engineering.

Which base agency should be contacted if the material safety data sheet (MSDS) is not available for a particular cleaning solvent?

Accept risks when the benefits outweigh the cost

Which basic principle of operational risk management (ORM) helps maximize unit capabilities by weighing risks against opportunities?

Intertocks

Which circuit control device works in reverse order?

IB

Which class of flammable liquid has a flash point below 73°F and has a boiling point at or above 100°F?

Class 75

Which class safety-toe shoe is the only one approved for use by Air Force personnel?

Orange. .

Which color code is used for designating electrical conduit and unguarded, dangerous parts of machines or energized equipment?

Magenta.

Which color code is used for piping system containers that contain radioactive substances?

Fuse

Which device is the simplest way to control an electrical circuit?

Transformers.

Which device is used to change power from one voltage to another?

Grounding sticks

Which device must be installed on high voltage equipment and used to discharge capacitors?

Statement of Work .

Which document can you use to get started when dealing with a particular contract?

Spats

Which equipment protects the upper part of the foot from hot metal splashes?

Reacting psychologically to situations according to previously habitual learned responses

Which example describes an attitudinal factor in relation to human factors in the mishap prevention program?

Methane

Which explosive gas commonly found in water treatment plants is not toxic but can cause thermal burns?

Mechanical compression.

Which factor contributes to work-related musculoskeletal disorders by creating pressure over a small area and interfering with blood flow and nerve function?

Location of the storage tank

Which factor is not considered when determining the size of secondary containment?

AF Form 979 and AF Form 1118

Which forms may be used to post notices of hazards in a workplace?

Systems Safety

Which function is not one of the three weapons program functions?

Sledge

Which hammer is made for heavy hitting?

Planning and engineering

Which hazard abatement measure is the most desirable way to eliminate hazards?

Procedural actions

Which hazard abatement measure recommends using protective equipment as a last resort?

that results in injury or illness to non-DOD personnel caused by Air Force operations.

Which incident would be an Air Force mishap? An unplanned event

Host safety staff.

Which individual is not a mandatory member of a formal hospital safety committee?

Spot

Which inspectionis conducted to check the day-to-day safety and health of an organization?

Operational analysis.

Which investigative technique is a reconstruction of the events and circumstances that led to the mishap?

System and subsystem analysis

Which investigative technique is used to look for too many parts, or evidence of foreign object damage?

Gamma rays

Which is an example of ionizing radiation?

To keep material from being thrown into the machine

Which is not a purpose of machine guards?

Outdated substances

Which items must not be allowed in pharmacies?

Oxidizers

Which kind of chemical may react vigorously at room temperature with carbon containing substances to produce fires or explosions?

3

Which laser class is of medium power and requires control measures to prevent viewing of the direct beam?

Time-critical

Which level of risk management is helpful in choosing an appropriate course of action when an unplanned event occurs during execution of a planned operation?

Strategic.

Which level of risk management should be used on high priority or high visibility risks?

B-5

Which maintenance stand has a variable height platform with a maximum platform load of 600 pounds?

C-1

Which maintenance stand is commonly known as the crew chief stand?

Bulletins

Which method of educating personnel should the safety office keep short, concise and to the point?

Man.

Which mishap-causing element of the 5-M model produces the majority of mishaps?

The presence of a flammable gas in excess of 10 percent of its lower explosive limit

Which of the following conditions creates a hazardous atmosphere?

Minimize dependency on hazardous materials

Which of the following is an objective of the AF Hazardous Materials Management Process (HMMP) program?

Satisfy Air Force Occupational Safety and Health concerns

Which of the following is not a primary objective of the vision conservation program?

Equipment grounds should never exceed two ohms

Which of the following is not a specific characteristic of effective grounds?

What if

Which operation risk management (ORM) hazard identification tool is the most powerful and is effective in capturing hazard data about failure modes?

National Safety Council

Which organization can provide consultant services on a safety problem?

Occupational Safety and Health Administration

Which organization's mission is to assure the safety and health of America's workers by setting and enforcing standards and providing training?

Investigation and analysis

Which part of the six-part narrative should follow the course of the investigation logically?

Brief synopsis or narrative.

Which part of the six-part narrative should give the reader the entire picture of the event without reference to any other portion of the report?

Commander

Which person is most responsible for carrying out the recommended corrective actions of an inspection report?

The steel wheel roller

Which piece of equipment is best suited to finish rolling flexible pavements and subgrades?

Safety plate

Which piece of equipment is used on the carriage of most saws for safely cutting the last piece of meat?

General

Which plan is easily updated and provides flexibility in response to command and installation changes?

Adequately secure the stock

Which precaution must you take to avoid possible injury, as well as damage to the saw, when you are cutting stock?

Local exhaust ventilation is usually preferred because it handles a smaller volume of air than general ventilation

Which principle accurately describes the difference between local exhaust and general ventilation?

It is worn to two-thirds of its original thickness

Which reason does not constitute a requirement to replace insulating matting?

Gate

Which safety device resembles an interlocked machine guard?

Pull-out

Which safety device uses operator wristbands to ensure a worker's hands are automatically withdrawn from the point of operation?

Extension cords must not be run through ceiling holes

Which safety rule should be observed where extension cords are used?

Off-set ratchet

Which screwdriver is especially useful in getting to screws under or behind pieces of equipment?

Process oriented description

Which section of the Air Force Manpower Standard 106A describes the duties of a wing safety office during normal peacetime operations?

Combat arms personnel

Which section of the security forces squadron implements weapons training for personnel on base?

Actions that correct the causal factors

Which selection best defines the results of a good mishap investigation?

Courtesy reports

Which service can other military services provide to your safety program?

Pneumatic-tire roller

Which soil compacting equipment can usually compact a four-inch layer of loose soil to 95 percent compaction in two to four passes?

The sheep-foot roller.

Which soil compacting equipment is best for compacting plastic soils?

Major command (MAJCOM) safety

Which staff is responsible for developing Air Force Occupational Safety and Health (AFOSH) standards supplements for unique operations for which safety and health guidance does not exist?

A flashing white light at a junction to the flight line indicates it is safe for vehicles to cross

Which statement is not true concerning vehicle operation on the flight line?

Analyze risk control measures

Which step of the operational risk management (ORM) process involves investigating specific strategies and tools that reduce, mitigate, or eliminate the risk?

Air Force Safety Automated System

Which system is used to transmit the majority of mishap reports?

Tab T - Investigation, Analysis and Conclusions.

Which tab in a formal mishap report is considered to be the most important?

Supervisors

Which tow team member(s) are authorized to give the "all clear to move" order when towing aircraft?

I.

Which traffic safety course improves driving by identifying and changing behavioral patterns that cause unsafe acts?

V.

Which traffic safety course may be commander directed for personnel who are convicted of serious traffic violations?

II

Which traffic safety course must be reviewed annually by the installation ground safety manager?

Type II, class G

Which type and class of safety helmet will offer protection against lateral blows to the head and reduce the danger of exposure to low voltage electrical conductors?

Flat

Which type of chisel should be used to cut sheet metal?

Mobile hydraulic crane

Which type of crane is considered the Air Force "workhorse"?

Leather

Which type of glove must be used as outer protection when rubber insulating gloves are being used?

Cnippers

Which type of goggles are designed to protect the eyes from relatively large particles flying from any direction?

Wire screen.

Which type of goggles should be used when ordinary goggles dust or steam over, affecting the wearer's vision?

ball peen

Which type of hammer should be used for heading rivets?

Fixed

Which type of machine guard is preferable to all others?

Long-nose

Which type of pliers is used for general electric work where space is limited?

Chemical cartridge

Which type of respirator offers protection against light concentrations only of gases and vapors?

Self-generating.

Which type of self-contained breathing apparatus is simple to use and requires less regular maintenance than the other SCBAs?

Steward

Which union official is responsible for enforcing the safety parts of the union contract?

Adjustable

Which wrench has the disadvantage of tending to round off the corners of hex nuts?

Commander

Who approves local written procedures as the authorization for operations involving licensed explosives?

Vice wing commander

Who chairs the Bird Hazard Working Group (BHWG) meetings?

The safety, bioenvironmental engineering, and fire prevention officials

Who conducts the evaluation and assignment of risk assessment codes

Supervisor

Who designates the electrical hazard areas that require the use of insulating matting?

Installation commander

Who determines (or designates someone to determine) when and where off road vehicles may operate on base?

Supervisor

Who determines that the placement of a danger tag is required?

Air Force Career Field Manager (AFCFM) for Safety.

Who determines training requirements and ensures implementation of training programs for Air Force Safety training?

Unit training manager

Who develops and coordinates training policy and program changes with work centers?

Group commander

Who ensures detailed local operating procedures covering safety precautions for hangaring aircraft are prepared and coordinated with installation ground safety and fire department personnel?

USAF surgeon general

Who establishes the monitoring program in the hearing conservation area to ensure compliance with federal laws?

Department of Transportation (DOT).

Who exercises final authority over the movement of explosives by common carrier?

Individual.

Who has the primary responsibility for identifying work place hazards that place workers at risk?

Commanders

Who has the primary responsibility for the mishap prevention program?

Commander

Who has the responsibility of making sure that off-duty safety briefings are provided to all personnel?

Air Force Chief of Safety (AF/SE)

Who has ultimate responsibility for AF safety programs?

Pilot

Who initiates signals regarding the operation of aircraft systems during marshalling operations?

MAJCOM.

Who is responsible for arranging external Environment, Safety, and Occupational Health Compliance Assessment and Management Program assessments?

Civil engineering personnel

Who is responsible for helping supervisors mark all circuit breaker boxes with the correct voltage?

Task-certifier

Who is responsible for identifying a trainee's strengths and areas needing improvements?

Safety supervisor

Who is responsible for maintaining AF Form 623,On-the-Job Training Record, or other approved training records of assigned airmen?

Interim safety board president

Who is responsible for preserving evidence during a mishap investigation?

Supervisor

Who is responsible for testing rubber insulating gloves and ensuring relevant records are maintained?

The manufacturer

Who is responsible for the initial classification of new lasers?

Commander of the mishap unit

Who is responsible to ensure toxicology testing is performed?

The Secretary of Labor.

Who is the approval authority for state safety plans?

MAJCOM commander

Who is the approval authority to deem an installation exempt from Environment, Safety, and Occupational Health Compliance Assessment and Management Program assessments?

President

Who is the final authority over the budget estimates before it is sent to congress?

Office of Management and Budget

Who issues a "call for estimates" each year to all agencies and departments of the federal government?

Ground safety manager

Who manages the mishap prevention program for the wing commander?

Base civil engineer

Who must approve the use of portable space heaters?

Fire chief

Who must approve welding done in other than approved areas?

Commanders, functional managers, and supervisors.

Who must notify the wing safety office of mishaps as soon as possible?

Functional Manager

Who must provide personnel with the approved eye protection required to do their job safely?

Supervisor and entrants

Who must sign the entry permit prior to workers entering a confined space?

Installation commander

Who regulates the movement of traffic and personnel on an Air Force installation?

Secretary of the Air Force.

Who takes the last official action to either approve or adjust the Department of the Air Force estimates?

Facility manager.

Who usually functions as the safety manager in a medical facility?

Base fire chief and security forces

Whom must the license requester coordinate with before submitting a license to the weapons safety manager (WSM) for approval of a request?

Supervisor.

Whom should you notify immediately if you encounter an imminent danger situation?

To protect privileged safety information in the report.

Why are safety investigations and legal investigations conducted separately

appropriate and feasible

Your hazard abatement recommendations should be

Local law enforcement

Your office has received a large number of complaints about the traffic flow at an intersection close to the base. Which non-Air Force agency or agencies do you contact as you try to solve the problem?

Massachusetts.

in 1867, which state began to use factory safety inspectors?


Conjuntos de estudio relacionados

Extra Conceptual Questions Chapter 15

View Set

Social Studies-life In The 13 Colonies

View Set