5 Level CDC URE's

1.10 005 Which is the correct method for writing 30 January 2011? a.20110130 b.01/30/11 c.30/01/11 d.11/01/30

a.20110130

1.28 011 Which publications are considered working handbooks? a.Air Force Manuals B.Air Force Pamphlets c.Air Force instructions d.Recurring Publications

a.Air Force Manuals

1.26 010 What types of property responsibility can be charged to DoD personnel? a.Command and custodial b.individual and custodial c.command and supervisory d.supervisory and custodial

a.Command and custodial

1.07 003 Which flight is part of a maintenance squadron? a.Test, measurement, and diagnostic equipment b.Maintenance operations and programs c.Quality assurance d.Resources

a.Test, measurement, and diagnostic equipment

2.021 206 What do you use as junction points for circuits that are frequently disconnected? a.connector plugs b.terminal boards c.shielded wires d.splices

a.connector plugs

2.029 211 Prior to soldering electronic equipment, ensure the equipment is a.disconnected from the power source b.connected to the power source c.protected from voltage spikes d.properly grounded

a.disconnected from the power source

2.002 201 When striking an object with a hammer, the hammer face should be a.parallel to the work b.offset to the work c.slightly angled d.slightly open

a.parallel to the work

2.006 201 When filing aluminum or lead, you should use a a.rasp b.scribe c.mill file d.triangular file

a.rasp

2.005 201 Which wrench is usually the strongest, fastest, and safest in a tool kit? a.socket b.box-end c.open-end d.adjustable

a.socket

2.015 205 Wire insulation may consist of several layers of noncunducting material that provides a.thermal protection a fluid resistance b.a method of identification c.protection from freezing d.strength and flexibility

a.thermal protection a fluid resistance

1.09 004 The Integrated Maintenance Data System (IMDS) Training Management Subsystem can be used to monitor a.upgrade training b.optional training c.seasonal training d.qualitative training

a.upgrade training

2.018 206 Which color code and corresponding wire sizes are valid for a preinsulated terminal? a.yellow-12 and 10 b.brown-22 and 20 c.blue-20 and 18 d.red-16 and 14

a.yellow-12 and 10

1.56 024 Which AF form is used to report ground safety accidents involving personnel (not involving acft)? a. AF form 711 b. AF form 711B c. AF form 117 d. AF form 117B

b. AF form 711B

2.036 214 When making wire connections to turret terminals, wrap the wire around the terminal at least a.90 degrees b.180 degrees c.270 degrees d.360 degrees

b.180 degrees

2.038 215 What is the heaviest duty soldering iron you normally use in soldering a printed circuit board? a.20 watts b.27 watts c.30 watts d.35 watts

b.27 watts

1.24 009 Bench stock supplies should be replenished when the authorized quantity on hand drops below what amount? a.40% b.50% c.60% d.70%

b.50%

1.55 024 Which mishap prevention tag is used to warn personnel against POTENTIAL hazards? a.Danger b.Caution c.Out of Order d.Do Not Start

b.Caution

1.03 (002) Who is responsible for managing the wing's quality assurance program? a.Flight chief b.Quality assurance section chief c.Maintenance group commander d.Aircraft maintenance squadron commander

b.Maintenance group commander

1.17 006 Which is a thorough and searching inspection? a.Minor b.Major c.Postflight d.HSC

b.Major

2.028 210 You can best determine a soldered connections' quality by a.reheating it slightly b.prying on it with a soldering aid c.giving it a good thorough visual inspection d.pulling on it gently with your fingers

c.giving it a good thorough visual inspection

2.004 201 One advantage of box-end wrenches is that they a.are the fastest to use b.can be hammered on safely c.are not likely to slip off a nut d.are easy to use on recessed bolts

c.are not likely to slip off a nut

2.034 213 During soldering, apply the proper amount of solder directly to the a.iron tip b.component c.connection d.heat bridge

c.connection

1.13 005 The AFTO form 244 is used to document discrepancies and corrective actions for a.aircraft b.batteries c.equipment d.multimeters

c.equipment

1.43 017 When you are servicing an acft with LOC, DO NOT wear a.cuffless trousers b. BDU cap c.leather welders gauntlet cuff gloves d.shoes which fit loosely around the top

d.shoes which fit loosely around the top

1.22 009 The first part of a national stock number indicates the a.part code b.bureau code c.item identification d.supply classification

d.supply classification

2.007 201 What type of gauge would you use to measure an actuating switch clearance? a.gap b.thread c.pressure d.thickness

d.thickness

2.030 211 How should you test the heat of a soldering iron? a.submerge the tip in flux b.hold the tip near your face c.touch the tip to solder, near your body d.touch the tip to solder, away from your body

d.touch the tip to solder, away from your body

1.51 021 Which element must be included in the workplace written hazard communication program? a.Hazardous material inventory b.Hazardous waste disposal procedures c.Telephone number of hazardous material monitor d.List of routine operations performed in the work center

a.Hazardous material inventory

1.36 014 Which kind of TO contains ops check procedures? a.Job Guide b.Fault isolation c.General Vehicle d.Schematic Diagram

a.Job Guide

1.45 019 What type of tasks may you perform in the immediate area of explosives? a.Mission critical b.Routine c.None d.Core

a.Mission critical

1.30 012 Which TO explains how to maintain and inspect a particular weapons system? a.Operations and Maintenance b.Methods and Procedures c.Time Compliance d.Abbreviated

a.Operations and Maintenance

1.16 006 Reducing the time an aircraft is out of commission is an objective of which inspection? a.Phased b.Hourly c.Periodic d.Isochronal

a.Phased

1.12 005 When a new AFTO form 781A is initiated, what kind of discrepancies CANNOT be transferred to the AFTO form 781K? a.Red X b.Red dash c.Red diagonal d.Discrepancies with a supply document number

a.Red X

1.53 022 What should be the main concern when planning the layout of any shop area? a.Safety b.Lighting c.Adequate work space d.Location of equipment

a.Safety

2.001 201 Screwdrivers are sized by the length of the a.blade b.shank c.handle d.ferrule

a.blade

2.040 215 Unclinched lead terminations are of what type? a.special b.convex c.standard d.concave

a.special

2.013 203 When torquing a bolt assembly, what is the force applied to overcome friction? a.torsion b.tension c.tensile d.shear

a.torsion

1.44 018 LIN must be stored below what minimum temperature to remain in a liquid state? a.-310.8 F b.-315.8 F c.-320.8 F d.-325.8 F

c.-320.8 F

1.57 025 High Frequency radiation is NOT produced by a.radio equipment b.radar equipment c.nuclear weapons d.ECM equipment

c.nuclear weapons

2.037 214 To connect wires or component leads to flat perforated terminals, the wrap must be a.45 degrees b.60 degrees c.90 degrees d.180 degrees

d.180 degrees

1.38 015 Revisions are issued when changes exceed what percentage of the basic TO? a.50 b.60 c.70 d.80

d.80

1.18 007 Which is NOT one of the elements of the maintenance training program? a.Upgrade training b.Management training c.Qualification training d.Cross-Utilization training

d.Cross-Utilization training

1.52 011 Which Air Force publication is a source of info for the prevention of accidents? a. AFI 91-202 b. AFI 8-2 c. AFI 91-204 d. AFR 39-1

a. AFI 91-202

1.37 014 While troubleshooting, you are using a wiring diagram to help you locate a malfunctioning component. After determining which component is faulty, you want to determine its PN. To do this, you would check the wiring diagrams a.numerical index b.Reference designator c.LRU index d.LRU designation

b.Reference designator

1.04 (002) Who is responsible for ensuring compliance with the wing Environmental Protection Agency program? a.Wing commander b.Squadron commander c.Propulsion flight chief d.Maintenance superintendent

b.Squadron commander

1.01 (001) There are how many levels of maintenance? a.Two b.Three c.Four d.Five

b.Three

1.35 014 The MIDAS page number is a.a 2-digit numbering system expressed as 1 element of 2 digits b.a 6-digit numbering system expressed as 3 elements of 2 digits each c.a 4-digit numbering system expressed as 2 elements of 2 digits each d.an 8-digit numbering system expressed as 4 elements of 2 digits each

b.a 6-digit numbering system expressed as 3 elements of 2 digits each

1.31 012 A series of red X's printed around teh border of the first page of a TCTO sgnifies a.an inspection action TCTO b.an immediate action TCTO c.a routine action TCTO d.an urgent action TCTO

b.an immediate action TCTO

2.023 208 Never use cushioned clamps in any bonding or grounding connection, because the cushion acts as a.a conductor b.an insulator c.a semiconductor d.an alternative path for current

b.an insulator

1.19 007 The PRIMARY responsibility for formal upgrade training rests with a.training management personnel b.commander c.the supervisor d.the individual

b.commander

1.27 010 An airman who signs out a toolbox assumes which type of property responsibility for that toolbox? a.supervisory b.custodial c.individual d.command

b.custodial

2.033 212 What do you have when you have a cold solder joint? a.low resistance to current b.high resistance to current c.an acceptable solder joint d.a bright and shiny soldered joint

b.high resistance to current

2.035 213 Which choice best describes a good solder connection a.a dull gray appearance b.no pits or holes and has a good concave fillet c.no pits or holes and has a good convex fillet c.bright and shiny with a minimum amount of pits or holes

b.no pits or holes and has a good concave fillet

2.027 210 Thermal shunts are used in soldering because they a.make the part heat faster b.protect heat sensitive components c.keep the lead and component at the same temperature d.give good holding action to the component being soldered

b.protect heat sensitive components

1.08 003 Quality maintenance is the responsibility of maintenance technicians, supervisors, and commanders who work in concert with a.maintenance training b.quality assurance c.resources d.egress

b.quality assurance

1.39 015 Safety Supplements to TOs are identified with a border of a.black SS's on the title page b.red SS's on the title page c.black SS's on all pages d.red SS's on all pages

b.red SS's on the title page

1.23 009 The second position of the ERRC Designator code indicates a. expendability b.repair level c.supplier d.cost

b.repair level

2.010 202 Before storing a torque wrench you have used, you should a.lubricate it with a light oil b.set it at its lowest setting c.check it for accuracy d.set it at zero setting

b.set it at its lowest setting

1.29 012 The list of applicable publications (LOAP) lists TO's that apply to a.active acft TCTO's b.specific acft c.overhaul depots d.a specific tester

b.specific acft

2.025 209 Oxide film is removed from the surface of metals during the soldering process by the use of a.a bristle brush b.the soldering flux c.a soldering iron tip d.an approved solvent

b.the soldering flux

1.33 013 In the basic TO numbering system, what is the MINIMUM groups of numbers each TO will have? a.two b.three c.four d.five

b.three

2.031 211 How should you remove excess solder from the soldering tip? a.Give the iron a quick flip b.wipe the iron on a damp sponge or rag c.gently tap the iron on a trash can edge d.let the iron cool and file away excess

b.wipe the iron on a damp sponge or rag

1.48 020 For personnel ESD, you MUST use a skin contact wrist strap connected to the workbench surface. This strap MUST have a resistance of at least a. 1 ohm b. 10 ohms c. 1 megohm d. 10 megohms

c. 1 megohm

1.20 008 What TO explains the Material Deficiency Reporting System? a.00-5-15 b.00-25-195 c.00-35D-54 d.00-25C-234

c.00-35D-54

2.017 205 Wires and wire bundles should be supported by clamps or grommets at intervals no more than a.15 inches b.20 inches c.24 inches d.26 inches

c.24 inches

1.21 008 A Category II, Product Quality Deficiency Report that has been submitted for a defect in workmanship MUST be forwarded to the screening point within a.1 workday b. 2 workdays c.3 workdays d.4 workdays

c.3 workdays

1.41 016 Personnel at the ALC activity must act on an emergency AFTO form 22 report within how many hours of receipt? a.24 b.36 c.48 d.72

c.48

2.008 202 The last verification date on a torque wrench must not exceed a.60 workdays b.30 workdays c.60 calendar days d.30 calendar days

c.60 calendar days

1.42 017 How far away from a parked acft should LOX carts be stored? a.25 feet b.50 feet c.75 feet d.100 feet

c.75 feet

2.039 215 You should clean the circuit board connection within how long after it has cooled? a.30 minutes b.60 minutes c.90 minutes d.120 minutes

c.90 minutes

1.06 002 Who is responsible to the maintenance supervisor for the leadership, supervision, and training of assigned personnel? a.Shift leader b.Section chief c.Flight commander/chief d.Maintenance superintendent

c.Flight commander/chief

1.05 002 Who is responsible to the squadron commander for maintenance production? a.Maintenance group commander b.Maintenance flight chief c.Maintenance supervisor d.Flight Chief

c.Maintenance supervisor

1.02 (001) If you work on an aircraft on the flightline you are doing what level of maintenance? a.Depot b.Intermediate c.Organizational d.Off-equipment

c.Organizational

1.59 026 What is a temporary storage location designed to store nuclear materials in transit thru a base called? a.Pyramid Alert b.Safeguarding c.Safe Haven d.Tempest

c.Safe Haven

1.49 021 Which situation illustrates a physical hazard presented by a chemical hazard? a.Acute liver damage b.Irritation of the kidney c.Second degree skin burn D.Chronic exposure to vapors

c.Second degree skin burn

1.34 013 The first number group within a TO number identifies the a.specific equipment b.section of the TO c.TO category d.kind of TO

c.TO category

1.46 019 What MUST you ensure when you are transporting squibs? a.Not to exceed the maximum amount of squibs b.Other personnel are not in the immediate area c.The squibs are in a protective container d.The use of a specially designed vehicle

c.The squibs are in a protective container

2.020 206 When joining copper and aluminum terminal lugs together on the same terminal board stud, separate them with a.a steel washer b.a copper washer c.a cadmium-plated washer d.an aluminum alloy washer

c.a cadmium-plated washer

2.032 212 An acceptable tinned wire has a.no insulation clearance and wire strands covered in solder, but still visible b.no insulation clearance and wires covered in solder, but not visible c.an insulation clearance equal to the diameter of the wire and wire strands covered in solder, but still visible d.an insulation clearance equal to the diameter of the wire and wire strands partially covered with solder, and still visible

c.an insulation clearance equal to the diameter of the wire and wire strands covered in solder, but still visible

2.009 202 A precaution concerning torque wrenches is to a.never use an extension with a torque wrench b.never use another wrench to secure a bolt before torquing c.never use a torque wrench that has been dropped unless it has been verified d.always calculate the leverage advantage before using a torque wrench above its rated capacity

c.never use a torque wrench that has been dropped unless it has been verified

2.019 206 The indent type crimping tool should be used only on a.preinsulated splices b.preinsulated terminals c.noninsulated terminals d.noninsulated terminal boards

c.noninsulated terminals

2.022 207 When heat is applied to thermofit material, which is used in compact wire bundles, it will shrink by at least a.one and a half times its original diameter b.one fourth its original diameter c.one half its original diameter d.one time its original diameter

c.one half its original diameter

2.012 203 A properly installed bolt has a minimum of how many threads protruding through the nut? a.four b.three c.two d.one

c.two

1.47 020 How much electrical current does it take to cause muscle paralysis? a. .001 amps b. .005 amps c. .010 amps d. .015 amps

d. .015 amps

1.54 023 What is considered to be a safe distance in front of jet engine intake ducts? a.10 feet b. 15 feet c. 20 feet d. 25 feet

d. 25 feet

2.024 208 After a bonding or grounding a jumper is installed, it should read no more than a.0.02 ohms b.0.01 ohms c.0.2 ohms d.0.1 ohms

d.0.1 ohms

1.32 013 What TO explains the TO numbering system? a.00-5-1 b00-5-5 c.00-5-10 d.00-5-18

d.00-5-18

2.016 205 Which TO provides instructions for the Brady Wire Marking system? a.00-20-1 b.00-20-2 c.1-1a-8 d.1-1a-14

d.1-1a-14

1.40 016 Which deficiency report is used for a TO deficiency that involves safety or the unit mission? a.Interim b.Urgent c.Routine d.Emergency

d.Emergency

1.15 006 Which inspection is used to detect defects that could have developed during ground operation of an aircraft? a.Preflight b.Thruflight c.Postflight d.End-of-runway

d.End-of-runway

1.58 025 Which type of nuclear radiation is the most deadly? a.Alpha b.Beta c.Delta d.Gamma

d.Gamma

1.50 021 What is the minimum info required on a hazardous chemical inventory? a.Name, location, and detailed ingredient list of the material b.Name, location, and quantity of material authorized c.Name and location of material d.Name of the material

d.Name of the material

1.60 026 Which safety standard of the nuclear surety program includes a pre-task briefing? a.Weapons security b.Individual responsibilities c.Prevent nuclear explosions d.Prevent unauthorized or accidental actions

d.Prevent unauthorized or accidental actions

1.25 010 Air Force property responsibility is imposed by law on a.commanders only b.all military employees c.commanders and supervisors only d.all military and civilian employees

d.all military and civilian employees

2.011 203 Tubing used in acft oxygen, fuel, lubrication, fire extinguishing, instruments, hydro, and vent lines is a.stainless steel and teflon alloy b.stainless steel and copper tubing c.aluminum alloy and copper tubing d.aluminum alloy and stainless steel

d.aluminum alloy and stainless steel

2.026 210 In order to clean a plated soldering tip, use a.a fine file while the tip is cold b.a coarse file while the tip is hot c.an abrasive cloth while the tip is hot d.an abrasive cloth while the tip is cold

d.an abrasive cloth while the tip is cold

2.003 201 What kind of pliers are good for pulling cotter pins? a.snap ring b.vise grip c.long-nose d.diagonal cutting

d.diagonal cutting

2.014 204 When installing a cotter pin, ensure the prong that bends over the bolt shank does not exceed the bolt nut a.grip b.width c.length d.diameter

d.diameter

1.11 005 A symbol entered on a maintenance form reflects the opinion of the a.shop supervisor b.maintenance officer c.squadron commender d.individual making the entry

d.individual making the entry

1.14 006 The five authorized inspection concepts used by the Air Force are a.major, minor, phase, isochronal, postflight b.major, minor, shop, home station, postflight c.periodic, home station, postflight, isochronal, programmed depot maintenance d.periodic, phase, isochronal, programmed depot maintenance, airline/manufacturer maintenance

d.periodic, phase, isochronal, programmed depot maintenance, airline/manufacturer maintenance